HobbyKing Online R/C Hobby Store : Hobby King 2.4Ghz 6Ch Tx & Rx V2 (Mode 2)

View all comments | (157 threads)

7/30/2010
steamhead19 (100%)
Is there only one receiver that will bind with the T6A v2 Tx? I have just bought one.
I would like to fly micros indoors so would like a very light weight Rx - is one available?
Any comments most welcome.

7/28/2010
Jose (100%)
I would like to ask how many positions the 3rd and 4th channel have. 2 or 3 position? Im looking for a radio with 3 position channels. Hope I made myself clear! Thanks! :)

Moss (100%)
2 for the switches.

Horacio (64%)
You can also use the knobs to get a continuous variation instead of fixed positions, if that suits you.

7/28/2010
Brunopracidiu (100%)
Hello is scheduled to have this radio when available?

7/27/2010
GOURA (50%)
How far does it send the signal to a receiver,for sure ?

7/26/2010
Ramen (0%)
How long it will take for you to have stock again? I'm a buyer from Europe.

7/25/2010
cole (23%)
can i use this on a 3d model

7/24/2010
DJFishinman (0%)
Does this not come with the dual receiver like the exceed one?

rcdragon (-121%)
no dual receiver

7/24/2010
ryan.perera22 (0%)
Is it just me or does it seem like after -20 stock the stop updating the number. I bought this when it was at -20 stock and it still is. So does this mean the actual stock could be -100 ? has anyone seen a stock lower than -20 on any item?

spartas phalanx (0%)
Yes i believe that that is the case or that it says back ordered after a certain time.

7/23/2010
FABIO GIL (0%)
I have bought this system a while ago and it came without the now included CD. Where can I down load the program from? Should I complain with HK about it? Thanks for any help.

7/14/2010
Adriano (0%)
I was wondering if the radio comes with battery for the RX and TX, thanks

ssacer (38%)
No, package includes Tx, Rx, bind plug, cable for programming and CD with software

Robert (0%)
Run like hell, this and the exceed rc version do not work with XP, Vista, or Win7.

No driver works and the computers never recognize the device.

carstent90 (67%)
No, for the Tx you might check that one: http://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=9787

7/13/2010
qualesh (67%)
How can i switch between rate mode and head hold mode with this transmitter, is it possible to assign a button for that?

ssacer (38%)
Add mix for variable A or B to channel 5, and when you turn the knob, gain change

Sam (25%)
The above is correct. Just plug the remote gain into the ch 5 slot on the rx, then mix knob a or b with ch 5 and set max and min to 100 and 0.

7/13/2010
bob74 (50%)
unable to program this transmitter:

I bought this 6 chanel system without the required USB cable... Then I ordered the cable.

I am still unable to program the transmiter from a win XP computer with the file available.

Does anyone know what to do ?

Robert

ssacer (38%)
Download this driver ***********silabs****/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx
And try this software: ***********sgr.info/usbradio/download.htm you must check what serial port is asigned to cable and select it in programming software

poffe_dk (50%)
THANKS ssacer.. I couldnt get the software that followed on the CD to work. But with the software just above, I have a connection.

7/13/2010
ssacer (38%)
I have problem with my HK-T6A v2. When throttle and throttle trim is all the way down, throttle on my throttle curve is on like 15%, and when it is all the way up, throttle is about 90%. At the moment I turn my Tx & Rx on, my motor starts. Throttle curve is 0,25,50,75,100 I have tried to callibrate it with T6recalibrate, but it is the same. Please someone help! Only thing I could do is put throttle curve 0,0,30,65,100 so i could fly.
Thanks!

Dillzio (98%)
you need to calibrate your ESC to the throttle range of the radio :o)

ssacer (38%)
My throttle range with ESC was calibrated, But I have solved it with digital radio sotware

Sam (25%)
I had the same issue. My esc had a programable throttle range though, so i calibrated it that way. Im still a little messed up in some of the programming but i can fly.

7/12/2010
berkay (50%)
Im planning to buy Hobby King 2.4Ghz 6Ch Tx & Rx V2 (Mode 2) but Im not sure I will find compatible receiver for it 3-4 months later. Do you guaranteed to supply its receiver? For example v1 receivers are out of stock and v1 transmitters are rubbish now.

7/11/2010
Ben (80%)
Hello
Im new to air planes and was wondering if i can buy a 6ch TX/RX and use it on a 4ch airplane

meatom (50%)
Yes you can!

Sam (25%)
Yep :)

cd_torr (20%)
Most definitely. Most people buy 6 or 7 channel radios to use on planes that require only 3 or 4 channels. It is always nice to have extra channels should you buy more complex planes that have flaps or retracts, which require those extra channels.

7/11/2010
e2tho (80%)
Hi, Can I use this Tx/Rx for my HK-450GT CCPM 3D..??
thanks

Gian_C (40%)
Yes. I am using with hk-450v2.

Sam (25%)
Yes u can. It is what i am using on mine.

e2tho (80%)
al last, I got my package today...what a dissappointed...when I open the box, I found the antena Broken, seem to me that they putted the broken Transmitter inside the box n send it out, when I received it, the box seem ok from outside....I didn't expect it, hobby king really disappointing......

7/10/2010
andres (75%)
I have a problem with my this RC. it has interference. It was demolishing my model aircraft and still has me without sign. To which this owes? Is it a problem of the RX or TX? And since can I avoid this??

Jacob (88%)
it is a low battery glitch not interference. never fly below 3.4 V per cell on the lipo in the plane.

7/10/2010
cole (23%)
can i use this bundle with the mini f86 sabre for sale

7/9/2010
Jacob (88%)
Has anybody (manually) tested the actual range of this transmitter and receiver?

7/9/2010
AEROBJ (75%)
Hello everyone, I wonder if this radio works with batteries or 8 and rechargeable battery. how many volts and charge him. Thank you.

Jacob (88%)
It will work with any 3s rechargeable lipo. you would have to open it and solder a positive and negetive wire out of it. 1800mah turnigy is a perfect fit. I would guess it also works with typical AA rechargables too that you can pick up off the shelf

UrsusRF (28%)
It need 12V. You can use any batts you want - NiCd\NiMh\Pb\LiFe\LiPo\LiIon

Sam (25%)
It takes 8 batteries, and calls for 12 volts. A non rechargeables is 1.5v so 8 equals 12v. I am using rechargeables and they work, but they only charge to 1.2v so 8 equals 9.6v This means that you have to charge them more than you would have to change batteries, but it is a lot cheaper to use the rechargeable kind.

ssacer (38%)
Yes you can, i am using them in all my Tx, including this one!

7/9/2010
Steven (37%)
Hi

I have purchased this controller & usb cable however i'm having issues where the controller is freezing in the software... I will not allow me to program and program keeps crashing..

I've installed the drivers/software on 2 computers and same result...

I don't know if the issue is the controller or if it is the usb cable causing the issue... can anyone please help me with my issue

thank you

frostbit (68%)
I had to use the one entilted
Driver for XP USB Cable (Not freeze with
The others frose keep at it,

Jacob (88%)
connect the cable using a 4 port USB hub.

MATTIASMTB (34%)
you have to instal the driver for xp first, driver for windows 7 after, and then plug usb cable, instal t6config, swich on the radio, open t6config, settings, choose COM port, and it will work.

7/8/2010
osherov79 (40%)
Hello! I recieved the HK-T6A V2 2.4ghz system and the cable for the simulator but it doesn't work. I have windows 7 and I have tried all the drivers that you recomended on your website but nothing works. How can you help me?

Shura (19%)
I felt different drivers, and only that is stable on any version of windows *******depositfiles****/files/a5nq2zbgi

This customer was awarded a credit for their answer.

Sam (25%)
Did set which com port the cable is plugged into and which one the software is talking to?

Shura (19%)
After installing the driver to select COM port number 3. T6config works with this. To work with the simulator except that the driver needs the program Virtual Joystick COM Driver PPJoy and T6sim. In the archives of these programs is specified as all set.

6/29/2010
kspuur (60%)
can i fly a heli with this, and if i can't, why??

lietuvys (70%)
Yes, you can. It has plane and heli modes.

killioughtta (-39%)
That depends on your ability :D

UrsusRF (28%)
Yes u can

6/28/2010
Conner (42%)
He's talking about the new version, not mode. I don't see any diffrence either.

6/28/2010
killioughtta (-39%)
I'd like to know what the difference between V2 and V1 of the HKT6a is. Nothing seems to have changed other than the fact only V1 Tx and Rx are compatible and V2 Tx and Rx with eachother.

zagonielod (55%)
Mode 1 has throttel on the right. mode 2 on the left

killioughtta (-39%)
Not MODE* Version 2 and Version 1. This is Version 2 and only Version 2 Rx is compatible with it. Why? What's the difference? I own Version 1 and I paid like $10 more for it so I want to know what the difference is.

Derick Z (34%)
I've got the same concern. I just bought the V1 right before this one came out, so I'm a bit miffed.

6/26/2010
BrentMatthews (34%)
Hi, Im using this for my quadcopter project. How do I program this to run all four motors off of one throttle? Brent

ssacer (38%)
For quadcopter you must have controller board, on witch you connect all four ESC, gyro etc.. Controller board connect to receiver.

6/9/2010
rewolff (18%)
It says HK-T6Av2 is compatible, where can I buy that? Searching for that string results in: sorry no matches were found.

6/7/2010
Jacob (88%)
***********>>> What is so special about "V2"?

Eaztah (43%)
I am wondering about the same thing. I have a V1 Tx, but I fried my Rx. May I use the v2 rx on a v1 Tx?

sseriy (60%)
2 Eaztah: Read description ->last 3 lines Note: Only HK-T6A receiver is comptible with HK-T6A transmitter. Only HK-T6Av2 receiver is compatible with the HK-T6Av2 transmitter.

mubariz (42%)
do they even sell v1?

G-areo (25%)
I'ts better than version 1 :)

BrentMatthews (34%)
the only difference between version 1 and two is the location of the throttle. On a version 1, the throttle is on the right stick, but on a version 2 the throttle is on the left stick.

j-bird (70%)
I have tested the the V2 and there is small range increase, and sends signal 0.023 times faster

6/7/2010
ohnjay (64%)
I do nor understand this system � if it is supposed to be a full range system I am surprised the Main Rx does not have dual antennas or, lacking that, that there is no satellite Rx?

6/5/2010
JAIME ALBERTO (34%)
HI FRIENDS. HOW CAN I BIND THIS TX-RX WITHOUT ESC? IF I CONNECT THE BATTERY TO THE BATTERY PORT IN TX, WHERE I HAVE TO CONNECT THE BIND CABLE-PLUG? THANKS
JAIME

zagonielod (55%)
When you are matching the TX with RX you have to connect the bind plug to the BAT port(channel), and the ESC cable to channel 3

mubariz (42%)
how does the rx get power without the batt?

JAIME ALBERTO (34%)
HI. I ASKED FOR BINDING WITHOUT E.S.C. THE CORRECT ANSWER IS: 1. CONNECT DE BIND PLUG-CABLE TO THE BATT PORT IN RX. 2. CONNECT RX BATT TO ANY CHANNEL PORT (CH1 TO CH6) IN RX AND CONTINUE THE PROCEDURE.
MUBARIZ. WHEN YOU USE E.S.C. TO BIND TX-RX YOU HAVE TO CONNECT BEFORE THE BATT TO THE E.S.C. THEN CONNECT E.S.C. TO CH3 (THROTTLE) THUS E.S.C. SUPPLY POWER TO RX. FOR THIS PROCEDURE E.S.C HAS TO BE TYPE B.E.C. BE CAREFUL WITH POLARITY. CONTINUE BINDING PROCEDURE.
JAIME

Lubis (50%)
You connect the battery to any channel and the bind plug to BAT

5/29/2010
Drone (20%)
Cant get the HK-T6A-M2 to work

1. Installed 'Win Vista or XP CP210x_VCP_Win2K_XP_S2K3.exe'
2. Installed 't6config.exe' from FS-CT6ADriver.rar (also tried the one from bmi-models)
3. Copied ser2pl.sys to C:\WINDOWS\system32 also C:\WINDOWS\system32\drivers
4. Reboot
5. Insert usb cable, check com port in device manager (was COM15)
6. cable adapter light glows
7. Plug other end to HK6, power on
8. start t6config
9. select setting->com15 (also tried with other ports)
10. Move HK6 stick

Also tried with Other USB ports
Try the entire stuff on Laptop (com4)

No matter what I do the Green bars on t6config just dont budge.
Any ideas..
I think my cable is fine. May be the HK6 ?? What say.
How to get this thing to work ?

Drone (20%)
Finally got it work with the usb cable.
(But doesnt work on my PC thou. Just my Laptop)
This is the driver:

***********4shared****/file/67056627/1766ee43/CP210x_VCP_Win2K_XP_S2K3.html

Lubis (50%)
Change the COM-port name to COM2 or something less than COM5. Mine didn't work with COM13 and I changed it to COM2 and it worked

HappyMan (29%)
Here www (dot) sgr (dot) info / usbradio you can find a driver that I successfully tested with Windows XP 32 bit and Windows Seven 64 bit and a better application (the demo version is freely downloadable) than the original (and very bad written) t6config software.

G-areo (25%)

I'm having a similar problem , I think the software may have a bit o a glitch ..

Drone (20%)
*Lubis
changed com to COM4 on my PC. Now it works fine on my PC too. (Driver is still CP210x_VCP_Win2K_XP_S2K3)
May be some time I will check with the driver from 1.
Thanks.

frostbit (68%)
Got mine 2 months ago, and pulled my hair out trying to get it to tack with PC. 7 hr of sun in laws time(he's a softwair writer) and 4 hr of brother in law's time (he dezines computor chips) and now it's tacking as of 2 days ago. great unit don't give up. My PC had a program on it that looked at the device and assined it the best driver. I had to take that program off my PC and strip out all usb drivers then put on 210x only. I get a choise of com1 or com3, only talks on com 3. Very finikey for us not so computor literet tipes. One thing I like most is control of Ch 5 &6 with the nobs. Reel fine radeo after you get it programing, but I swear I almost used it for Target Pratis.

frostbit (68%)
Hi agen, even thow it tock 3 months to get mine programing, I had instaled one of the 3 extrea recevers I ordered with the radeo in a cub. I instantly went out and flew it without rangechecking as soon as I had Ch. 3 & 4 reversed. So two days later I'm thinking I'm dumb as a stick! Range checked with a Futaba recever batery,( Key filed off ) recever, servo and 36" of penio wire all scoch tayped togeather to sinulate worst case senero. Over concreat and asfalt movement of servo started getting scatchy at 675 yards 617 meters. All field conditions, weather, and magnetic influences will proubly change that, but it's a reference that speakes well for an inexpencive system, Happy flying.

5/21/2010
Nickeystar (61%)
This guy from Hungary built this wonderful LCD for the T6, unfortunately he don't sell it.
HK, if you produce this one i promise to buy 10.
here is the link:
http://www.youtube.com/user/boldivi#p/a/u/1/5zSGVaPmMzY

5/20/2010
NASAAN101 (20%)
Guys, Will this Radio work for and RC cobat Cruiser? i've been looking at others and a friend told me about this? Thank you! Nikki

Tatnorway (0%)
I assume that is an old warrior boat? Of course it will :)

NASAAN101 (20%)
Tatnorway,
She was a WW2 Cruiser! She 3.5 units! And she she has 2 guns and a full unit pump! now i know this radio needs a PC cable, but can you program it and will it remember, what you have in it?
Nikki

Derick Z (34%)
Yes it does 'remember' what you've programmed. It only needs the computer for initial set up of servo reversing and throw limits, etc. After that it's good to go, unless you want to change models or adjust any quantities, at which point it's back to the computer.

NASAAN101 (20%)
Hey Derick,
I know this radio come with 1 x 2.4Ghz transmitter, 1 x 2.4Ghz Receiver, 1 x Bind Plug. Can you tell me a little more about this radio? Thank you,
Nikki

Derick Z (34%)
Well it's programmed through a computer only, which can be a bit of a pain in the field. Hope you've got a laptop! It's been working well for me, and no drops in signal so far up to 50m or so. What do you want to know? Or am I too late? Make sure you order the program plug! It does NOT come with it! You can set up mixing to use the two dials on top, and can set each of the two switches individually as well.

5/20/2010
NASAAN101 (20%)
Guys,
Will this Radio work for and RC cobat Cruiser? i've been looking at others and a friend told me about this? Thank you!
Nikki

5/16/2010
Derick Z (34%)
I just want them to be in stock alread! My HK450 is just sitting there waiting for a Tx to get her up! It's mid May, so I guess 2 weeks max and they'll come in.

So frustrating! :P

5/12/2010
zagonielod (55%)
I came also with a question: What simulator program would be compatible with this radio? Real Flight G5 is compatible? Or if you know about a freeware which would be compatible, would be much appreciated.
Thanks in advance!

dido41987 (69%)
The freeware FMS is compatible, just install t6sim, search google. Real Flight is compatible at the moment only the 4.5 version. You have to install a Dongle Emu (3.3) to let it work!(after the t6sim)

Lubis (50%)
Can't answer which it'll work on, but I can tell you this. It doesn't work with FMS or HeliSimRC

Tatnorway (0%)
I have not been able to get it to work wit RFG5, but it works perfectly with Aerofly, as long as you make a new configure as an "acro" plane without any other settings :)

5/8/2010
manfredo (15%)
In the video of the link,

http://www.hobbyking.com/hobbyking/store/HK_movies2.asp?idmovie=51e46014327f406eb9907c987c80e912

Show a T6 config card, Where I can acquire this card

dido41987 (69%)
You just need the usb Cable: Hobby King 2.4Ghz 6Ch Tx USB Cable for Win2000/XP to let it work

manfredo (15%)
Yes, I know it, but I think that the T6 config card is a nice solution when we are in the field

5/3/2010
Psycho Sidd (17%)
Still having problems with the same problem..... I have all the softwares downloads and I have a non-powered 4 port hub. I am useing XP and Vista on 2 different comptures(with downloads). On my Vista I click on Setting and it gives me one port (COM3 non responseive) and one my XP it gives me noting.... What am I doning wrong HELP PLEASE .....

dido41987 (69%)
Try to download the latest driver, just search for PL-2303 Driver. Then use this procedure: Install the USB driver first. (PL-2303 Driver Install.exe) Install the t6config.exe program next. Plug the USB cable into the Computer. Click through the hardware detection screens. After the USB hardware detection screens, turn on the power to the Tx (did you install batteries?) run T6config.exe Click the "Setting" button to select the serial port that was created by the USB install (likely the last on the list). If it is communicating, you'll see that moving your sticks make the green/black bars at the top move. Click "Get User" to get the Tx setup loaded into your PC. Click "Save" to save your settings (do this before you make changes so you have your defaults saved). Note: Do not edit or save your config files without the Tx plugged in and communicating. I have found at least on my system, if I do this, it does not always save the data right if you work w/ T6config.exe when the transmitter is not plugged in and communicating w/ the PC. I did not have any issues w/ installing my USB driver. I installed the driver BEFORE plugging in the USB device. But if you do, I heard this helps. Download the MS Windows serial USB system file, called "ser2pl.sys" from here: ***********floridaprobe****/usb_install.htm The cable uses the Prolific PL-2303 USB chip. Apparently it doesn't always get recognized by Windows, so the system file doesn't get installed correctly. Download the system file, and copy the file to your C:\Windows\System32 folder. Plug in the USB cable into your computer, then restart your computer with it plugged in. It "should" get recognized at startup.

Lubis (50%)
Check the COM-port name. Mine was COM13 and it didn't work, I then changed it to COM2 and it worked fine

4/30/2010
Psycho Sidd (17%)
Do you have to use the "Hobby King 2.4Ghz 6Ch Tx USB Cable for Win2000/XP" Cable to program it or can you use any ole cable???????? HELP

Bas123 (42%)
this cable is very cheap, so just buy 1, because you will need it!

dido41987 (69%)
The cable it's just a serial-USB conversion cable, you can use any serial-USB conversion but beware to find the right pins to insert in the serial port, i don't know them

komnata507 (15%)
Yes any usb cable

Tatnorway (0%)
You have to use that cable yes. Just by it! It is so cheap!

4/28/2010
marcos (95%)
this is standard futaba radio. I use a cable radio futaba trainer?

dido41987 (69%)
I think that the pins are different

Click here to see all comments