13T/5mm M1Steel Pinion Gear

 phdpasso 101 points

What do you mean ?

 grimmjow 1690 points

yes, need more choice of theeth number !

 phdpasso 101 points

Definitely is steel and seems to have been hardened. Didn't install it in the car yet.

 Petr 5 points

I have this Pinion Gear and is hardened steel. Very good quality.

 phdpasso 101 points

14.86 mm

 Mikalai 6 points

You can use pinions from 2wd desert buggy. It 3.17mm motor shaft and 48p - perfect for yor traxxas www.link

 Robert 20 points

No, this is mod 1.

 IgonoZ 1 points

Sorry for the "No Credit given". Clicked wrong btn

 Robert 20 points

No, this is MOD1

 Outbreak 18 points

what is mod 1 means ?

 Robert 20 points

Mod 1 is Module 1. Used in metric which is basically by formula, Module = (25.4/DP). DP is the diametral pitch(english). Say 32dp = 0.8 Mod. So basically MOD 1 has a bigger tooth than 32 pitch.

 Outbreak 18 points

tnx so much..

 gouldie 401 points

i dont think your be able to do it with out any fancy equipment. what do you need to harden it more for. it comes hardened and im using a few of these with steel spur gears and they are still like new. nearly 2 years use

 Arsya 161 points

yes, this is a Mod1 13T pinion

 Arsya 161 points

of course you can. Thise pinion maden by steel, so it will be fine to use it like that

 gouldie 401 points

yeah these are fine to use with steel gears. i use a couple hobbyking pinions with steel spurs gears and they are still like new. just make sure you fit the pinion with the correct gap and your have no problems

 gouldie 401 points

no the standard motor that comes with the A2016T has a 3.175mm shaft and this pinion is for a 5mm shaft hobbyking dont sell car pinions to fit 3.175mm

 Iain 1 points

Is there anywhere you know I could get one - or is there a way of adapting? Would the teeth work with the spur gear on the diff at any rate - if that works, there is probably some way to shim it.

 gouldie 401 points

you can get brass tube that fits over the motor shaft and has a 5mm outside diameter and drill a hole in it so the grub screw fits throw and clamp onto the motor shaft. and have a look on ebay for pinions that fit. the size you need are normally pinions used on 540 brushed motors as brushed motors have a smaller shaft hope this helps

 Iain 1 points

Thanks a lot, very helpful

 jordsnissannx 19 points

you can buy a sleeve adaptor but i dont think hk**** sell them, i got mine at a local hobby shop to put this pinion on a hpi bullet, 3mm shaft but it uses m1 pitch, this gear works perfect with the adaptor sleeve

 troy97 100 points

Yes, it will, Mod1 is the correct pitch for trooper. But note, that stock trooper pinion has 14 tooth, this one is 13T, your car will become a bit slower.

 Germano 42 points

That pinion is made for 550 class motor with 5mm motor shaft diameter and module 1M(used in 1/8 cars). Trooper's motor is 540 class motor with 3.17mm motor shaft diameter. Trooper's pinion is module 0.8M. That means it doesn't work in the trooper. Sorry. But there is the original pinion here. []'s

 troy97 100 points

Yes, it fits Trooper, I have it, and seems, that Germano does not! Mod1 pitch and 5mm shaft is exactly what you need for that truck.

 troy97 100 points

I pulled out the stock pinion from my trooper today and was really amazed, motor shaft has 5mm diameter, but it reduced to 3.175 on the end where pinion is fixed. So I was wrong, stock pinion is 3.175mm. I think, it's better to change motor for a normal with 5mm shaft, because there is no mod1 3.175mm pinions anywhere.

 Vassili80 141 points

I tink not. The trooper have the motor shafs much thinner. This pinion is for 5 mm motors.

 Germano 42 points

I have this pinion gear and it works with 1/8 brushless motors and mod 1 pitch.

 1111mavrick 151 points

The trooper IS a 5mm shaft right?

 Germano 42 points

That pinion is made for 550 class motor with 5mm motor shaft diameter and module 1M(used in 1/8 cars). Trooper's motor is 540 class motor with 3.17mm motor shaft diameter. Trooper's pinion is module 0.8M. That means it doesn't work in the trooper. Sorry. But there is the original pinion here. []'s

 lubos5 18 points

where i can buy the original trooper pinion?
thanks

 troy97 100 points

What are you all talking about, trooper has 5mm shaft and mod1 spur gear, this pinion fits like it was made for trooper!

 troy97 100 points

motor shaft is 5mm, but it reduced to 3.175mm on the end, I was wrong. This pinion fits only if You use 3.175 to 5mm shaft adapter.

 NeoNot 54 points

It fits my 32pitch spur without issues.

 Purple 6 points

I think 24 -2 becose its 2x bigger than 48P

 Vassili80 141 points

is the metrical p1 module,I don t tink it will fit non metrical gears.

 Outbreak 18 points

so its 32 pitch or not ??

 Outbreak 18 points

NeoNot hi. im gone use this on slash.. will it work ?? spur is 32 pitch :S

 Crumbshark 9 points

I am also curious...will this be restocked soon?

 rizky_p 214 points

1 Jason will this be restocked soon?

 Vassili80 141 points

is not harded,so it wear very fast if work whit steel spur gear.

 Crumbshark 9 points

Coming into stock again soon??? Been waiting a while on my order, Ill cancel this item if it isn't expected soon.

 Grzegorz 198 points

Yes, since all those good motors are only for 5mm shaft.

WE NEED 0.6MOD (TAMIYA) PINIONS FOR 5MM!!!

Sorry for shouting, but honestly all those hobbywing/ezrun motors (3.17mm shaft) are horrible for offroad. Only good motor I have found are with 5mm shafts :/

 catalin_RO 229 points

when is going to in stoc. i have it in an order. i need it as soon as possible. thx eduard romania

 Psyho 254 points

www.link

 catalin_RO 229 points

we need more teeth pls.