Please confirm your location:

USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Radios & Receivers > Turnigy


Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)

Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)

With v2 firmware update, correcting many flaws of the previous 9X, plus inbuilt 2.4Ghz (no daggy second antenna) this is a quality, reliable 2.4Ghz system suitable for beginners and pro pilots alike.
Get that locked-in feeling that only 2.4Ghz glitch free technology can provide.
Ultra fast reaction times and interference free control of your model is only achievable with this 2.4Ghz technology.

Without a doubt, the best value 9Ch system available!

Number of Channnel: 8ch ppm/9ch pcm
Display: 128*64LCD
Support Type: Heli/Acro/Glid
Support user: 8
Stick model: 4
Encoder type: ppm/pcm
Subtrim: Yes
Simulator Interface: Yes
Buzzer: Yes
Low Voltage Show: Yes
Turnigy 9x 9Ch Transmitter
Turnigy RF9X-V2 module
Turnigy 9X8C-V2 8-channel receiver
The TURNIGY 9X has been reflashed with the new v2 firmware, fixing previous menu and mixing issues. This firmware flash is only available from our TURNIGY 9X system as we flash each unit in our office before it is shipped.
Purchases of any other rebranded version of the TURNIGY 9X will not have the latest firmware and patches (even the OEM factory does not have these updates).
NOTE: "SWITCH ERROR" means you have one of the switches in the wrong position when you turn the radio on. It is not a fault.


This product available from a warehouse near you!

Weight: 1375g
International Warehouse
USA West Warehouse In Transit View Item
USA East Warehouse In Transit View Item
Price  $59.99

  • Turnigy 2650mAh 3S 1C Lipoly Tx Pack (Futaba/JR)

    Combo Price: $12.75   IN STOCK

  • OrangeRX DSMX/DSM2 Compatible 2.4Ghz Transmitter Module (JR/Turnigy compatible)

    Combo Price: $29.95   IN STOCK

Further discounts available for registered & logged-in customers.
 Customer rated
Total of 4436 discussions.
Rui  1 points - 3/2/2015
Hello. When is it going to be available in Europe again? Thanks!
 v_max 4564 points
subscribe for email notification under product description and you will be notified by email.
Griffith  1 points - 3/1/2015
I have two of these and I want to use the buddy cord to help a mate of mine..... Ive followed all the correct procedures on setting it up and it still doesnt work? any ideas and also can the switch be reversed...hold the switch to be the mastr seems abit **** about face
 Ronaldo 29 points
I had a 9X and reversed the training switch wires, worked perfectly. Open the transmitter and locate the trainer switch. You'll notice it has 3 pins (2 soldered). Unsolder the outside wire and solder it on the opposite pin, leave the center pin where it is. Your switch should work like in any other radio. For the settings check this video: Hope it helps
 Griffith 1 points
Thank you very much for your reply !! I will give this a go tomorrow :)
Sasa  6 points - 2/28/2015
When I turn it on the transmitter turns auto off after two or three sometimes five seconds?? Why
 Miguel FP 1658 points
This transmitter doesn't have auto off. Are your batteries fully charged?
 glenn_mech 566 points
i encountered same problem too with my 9x...i opened it up and tighten the lose switch.
 Sasa 6 points
I will send you tomorrow when my batteries will be fully charged
 Miguel FP 1658 points
Thanks for the credit. Hope to hear good news from you.
 Sasa 6 points
Yes the news are good,thank you very much,glenn_mech thanks ,you at least tried
Matneymodels  34 points - 2/27/2015
Is there a way to use this TX to just run a set of lights for Pylon at ! pylon. All I want to do is run 4 lights at #1 pylon. I will use the switch that HK sells to turn on the lights.
 v_max 4564 points
Yes, just connect switch to free channel on RX and assign desired t9x switch to this channel in mixer menu
 Matneymodels 34 points
I want to just put 4 push buttons switches, How would I wire it?
 v_max 4564 points
you need 4 power switches each connected to own channel on RX. t9x has enough 2pos switches to control 4 channels so you only need to assign it in mixer menu.
 Matneymodels 34 points
I need to find out how to wire 4 switches off the TX box it self. I will 4 people at 1 table doing this work at the same time. That way they need 4 switches for each 1 person at 1 time.
 v_max 4564 points
Just extend switches wires out of tx box I guess..
Garry  1 points - 2/27/2015
what is the range of 9x
 v_max 4564 points
Safe range vary from 100 to 300m... on line of direct view. (due to not stable quality of RF part ) and depending on surrounding conditions (like EMF noise around fog, clowds and even humidity) Max range is about 800m...some people reports over 1km... but it's unsafe. Chance to loose signal (and yor craft is too high)
Customer Reviews
Review Blogs for this item
A very god radio !!!
Bind Addtional Turnigy 9X 2.4 GHz 8Ch Receiver (V
Bind the HK-GT2 3ch 2.4 GHz with the Turnigy 9X
Bind Turnigy 9X V2 with HK TR6A V2 6Ch
Turnigy 9x stock levels
Attention! Lot with display problems.
Total crap
Overall Rating
14 thumbs up!
I am using an ASSAN hacker modulewith the 9X Tx.
With no recievers available I hooked up the Hacker as follows:
1- Top Pin signal
2- no connection
3- Red plus
4- Black -
5- no connection.

You can see photo's at only gave it 4 stars as the TX did not work as recieved, one of the wires to the dual rate switch was not connected, an easy fix.

19 comments. Reply..

Create an account
Overall Rating
9 thumbs up!
I'd give this radio a 5 star rating but there are a few minor things that subtract points.
-One is that putting the batteries is a hassle, the 8 AA cell holder is OK, but the cable gets on the way of the cover and it takes a while to be able to close it, there's a lot of pinching of the cables involved so I shouldn't wonder if the insulation fails sooner or later requiring a replacement of the cables.
-Second is the very annoying and loud BEEEEP!!! you get with every-single-click you do on the buttons, seriously stressing to set up the radio at home, not good for conjugal life. To fix that I cut the leg that goes from a transistor to the speaker and added a 220 Ohm resistor in between.
-Third, no manual comes with the radio.
-Fourth setting up a V-Tail was a mind bending affair, I succeeded but I couldn't grok the logic of the procedure.

Besides those things it's a good product.

25 comments. Reply..

Overall Rating
8 thumbs up!
I have one of those and i have kinda problem with display, there is some cold conract, on mainboard, ans still bordering me all the time( otherwise seems ok the menu and functions.

7 comments. Reply..

Overall Rating
8 thumbs up!
I purchased this transmitter & Assan XJ8 module from HC. First I got around the switch error bug (thanks to that reviewer)
For me the Assan XJ8 just flashes red once on start up, but gives no steady red LED & will not go into pairing mode.
Assan say they don't know the problem & suggest putting XJ8 in another TX (I don't have one)
Anyone know how to test if TGY 9X or Assan is the problem? Thanks

11 comments. Reply..

Overall Rating
7 thumbs up!
Great range - over 3000m, but realy to big receiver. Also dont like to small battery compartment, and antenna linked with wire.
You Also can't mix with AUX cahnnels - you can oly mix first 4 cahnells. No manual - It could be at least link at this product to download manual for Turnigy 9x. Also don,t like that this transsmiter in almost never in stock, or that there smaller 6 ch receivers I waiting for more 3 months So from me only 3 stars.

25 comments. Reply.. here to see all reviews
Aff. Link