Please confirm your location:

USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Radios & Receivers > Turnigy


Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)

Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)

With v2 firmware update, correcting many flaws of the previous 9X, plus inbuilt 2.4Ghz (no daggy second antenna) this is a quality, reliable 2.4Ghz system suitable for beginners and pro pilots alike.
Get that locked-in feeling that only 2.4Ghz glitch free technology can provide.
Ultra fast reaction times and interference free control of your model is only achievable with this 2.4Ghz technology.

Without a doubt, the best value 9Ch system available!

Number of Channnel: 8ch ppm/9ch pcm
Display: 128*64LCD
Support Type: Heli/Acro/Glid
Support user: 8
Stick model: 4
Encoder type: ppm/pcm
Subtrim: Yes
Simulator Interface: Yes
Buzzer: Yes
Low Voltage Show: Yes
Turnigy 9x 9Ch Transmitter
Turnigy RF9X-V2 module
Turnigy 9X8C-V2 8-channel receiver
The TURNIGY 9X has been reflashed with the new v2 firmware, fixing previous menu and mixing issues. This firmware flash is only available from our TURNIGY 9X system as we flash each unit in our office before it is shipped.
Purchases of any other rebranded version of the TURNIGY 9X will not have the latest firmware and patches(even the OEM factory does not have these updates).
NOTE: "SWITCH ERROR" means you have one of the switches in the wrong position when you turn the radio on. It is not a fault.

* Special Offer Price, Limit of one per customer.


Weight: 1375g
International Warehouse
USA West Warehouse In Stock View Item
USA East Warehouse In Stock View Item
Price  $60.35

  • Turnigy 2650mAh 3S 1C Lipoly Tx Pack (Futaba/JR)

    Combo Price: $12.75   IN STOCK

  • Turnigy 9X Replacement 2 Way Switch A (Short)

    Combo Price: $0.78   BACKORDER

  • Turnigy 9X Replacement Switch B (Long)

    Combo Price: $0.94   BACKORDER

  • Turnigy 9X Replacement Reset / Trainer Switch

    Combo Price: $1.00   BACKORDER

  • Turnigy 9X Replacement 3 Position Switch

    Combo Price: $1.02   BACKORDER

  • Turnigy 9X Replacement Switch Retainer

    Combo Price: $0.04   BACKORDER

  • Turnigy 9X Replacement Mother Board

    Combo Price: $9.11   BACKORDER

  • Turnigy 9X Replacement LCD Screen

    Combo Price: $5.35   BACKORDER

  • Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)

    Combo Price: $59.95   IN STOCK

Further discounts available for registered & logged-in customers.
 Customer rated
Total of 1563 discussions.
Hector  1 points - 9/27/2015
I am buying this article and after i programmed him several times continue with the same problem so I request the refund of the money thanks.
 anikeev 1394 points
You should contact HK-staff by live-chat to get more help. This discussion page is for customers Q&A, there's no HK-representatives.
Chris  1 points - 9/21/2015
Is this combo CPPM capable?
 Hector 1 points
Is the "turnigy 2.4G 9 channel
paul1  5 points - 9/7/2015
i bought this transmitter and receiver and HK 401B gyro to set it up in Align 450 helicopter. Everything are fine except the Gyro is not working properly, first the red light on Gyro will turn off as soon as the transmitter is turned on. second the helicopter will spin round when throttles up. just wonder what exactly setting I need to set on the transmitter?
 anikeev 1394 points
Please note, that you have only 4 channels work out of the box. If you use more than 4 channels you need to set em up properly. If you made that - make sure that all channels works right way. Sometimes you need to reverse 5th channel or any other. ps - people buy this radio for absolutely ANY model. So it's better to ask your questions where Align-heli users gathering. On a forum or Align 450 discussion page. You'll get help there much quicker.
melaluka  9 points - 9/5/2015
how do you get channels 5 an 6 to work
 anikeev 1394 points
Read the manual, please. So you will find out how to set up that channels in desired way. I use 5ch as gear switch and 6ch as 3-position switch, but some heli-pilots use that channels for mixing (plane pilots use for elevon mixing). You can also find a lot of videos on youtube - just specify your question.
Timothy  1 points - 8/19/2015
What simulator cable can i use to be able to run Phoenix RC simulator with this transmitter if pssible? Thanks!
 John Banion 157 points
Just search for "SIM Cable". I use the blue one with windows 7 no problems. However I have seen a few 9x's with flaky trainer ports. cold solder joint.
Customer Reviews
Review Blogs for this item
Bind Addtional Turnigy 9X 2.4 GHz 8Ch Receiver (V
Bind the HK-GT2 3ch 2.4 GHz with the Turnigy 9X
Bind Turnigy 9X V2 with HK TR6A V2 6Ch
How To Increase Your TURNIGY 9X Radio Stick's Ten
Turnigy 9X REVIEW and SPECS
Overall Rating
Straight Up
53 thumbs up!
I bought this to supersede the HK-T4A transmitter. It comes as a bare transmitter - no batteries, no charger, no instruction manual, and no module (not even 72MHz). This is all OK, as I only use Lipo batteries, hate the cheap transmitter chargers, and ordered an Assan 2.4GHz JR-type module along with the order. Hobby King were up-front with all of this from the start, except the lack of a manual. The manual is available online, as the IMax 9, and the lack of a manual saved me further shipping dollars - a big factor in ordering something cheap.

The good news, it's not a cheap-feeling radio. The gymbals are really smooth, almost to the same standard as my Futaba 9C. Even the throttle ratchet is quite smooth, which is essential for heli flying. The case is plastic, but it feels nice in my hands.

Control with the Assan module was absolutely locked in. The availability of exponential restored my Shocky back to the smooth flying wonder I had originally built (with the HK-T4A I could not get it to fly smooth - I've become addicted to expo). The precision was also really noticable as I fed in gentle "tickles" on the sticks. Outstanding!

The misses (deduct one star):
IF YOU USE EXPO YOU CANNOT USE DUAL RATES!!!! Even 1pcnt of expo disengages any dual-rate settings, even though the rate settings are still there on the screen. I was initially really disappointed about this, until I realised that I hardly ever use dual rates. If you depend on dual rates, this is a FATAL

32 comments. Reply..

Overall Rating
21 thumbs up!
This 9 Channel Transmitter is excellent, I am using this unit with the FRFRY 2.4Ghz module (JR compatible) and it work smoothly, I prefer the FRFRY over the Corona because the FRFRY is a TRUE Frequency Hopping system (very much like the FUTABA FAST) and is smoother on the servos, Also tested the Dual Rate and Expo and contrary to some reviews in my case work perfectly, remember to channel one at the time (expo or dual rate) and get out of the me

16 comments. Reply..

Overall Rating
12 thumbs up!
The transmitter is super. He works with Graupner / IR modules 35MHz/40MHz and Corona / TGY 2.4 GHz einwandfrei.I 've seen here

6 comments. Reply..

Overall Rating
Jonas Mar
4 thumbs up!
Today I received my Turnigy 2.4 G & Assan module, really very nice & good quality, I binded the two receivers to the module following the Assan instructions, it was very easy, excellent sistem at a very good price, thanks HK

3 comments. Reply..

Create an account
Overall Rating

3 thumbs up!
Great transmitter for the money. I bought a Mode 1 and switched it to a mode 2. (HK was out of Mode 2 tx) Very simple to do.

8 comments. Reply.. here to see all reviews
Aff. Link