USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Radios & Receivers > Complete systems
> Radios & Receivers > 2.4Ghz HobbyKing

  RATED:

Hobby King 2.4Ghz 4Ch Tx & Rx V2 (Mode 2)

Hobby King 2.4Ghz 4Ch Tx & Rx V2 (Mode 2)
Hobby King 2.4Ghz 4Ch Tx & Rx V2 (Mode 2)

HobbyKing 2.4Ghz 4Ch Tx & Rx V2 (Mode 2)(THROTTLE ON THE LEFT)
Hobbykings T4A 2.4ghz system is an entry level transmitter offering the reliability of 2.4Ghz signal technology and a receiver.

The T4A makes a good backup transmitter or a take anywhere unit. Drop it, scratch it, leave it in the car and forget about it. This is what the T4A is all about.
Not suitable for the multi flapperon, mixer, vtail, FPV, robot controlling hobbyist.
 
Key Features;
4-channel 2.4GHz transmitter with servo reversing.
Easy to use control for basic models.
Includes 6-channel receiver
Trainer system option.
This system does not need a PC to program servo direction.

Included;

1 x 2.4Ghz transmitter
1 x 2.4Ghz Receiver
1 x Bind Plug.

Note: 
Only HK-T6A receiver is comptible with HK-T4A transmitter.
Only HK-T6Av2 receiver is compatible with the HK-T4Av2 transmitter.

PRODUCT ID: HK-T4A-M2

This product available from a warehouse near you!


Weight: 989g Quantity: 
United States Warehouse In Stock View Item
stock
10+
Price$23.02


Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
5408
crowns
  
 
Total of 553 discussions.
Yigit  1 points - 4/23/2014
 
Hi , i am using hk-t4a for a long time. After a winter break, i ve taken my quad from the garage. But there is a problem: I cannot arm my quad. When i get the stick to bottom left position nothing happens. I made receiver test, everything is OK, calibration is OK... What may be the problem? Any idea?..
 Trygve 3 points
Make sure that your rudder isn't reversed
andrea  1 points - 4/22/2014
 
Is good for electric car?
 Trygve 3 points
The throttle isn't spring loaded but otherwise it would be good.
Jon  4 points - 4/16/2014
 
Some that have the original “*t6config”* or “*Digital Radio”* config file for HK-T6A V2 ? /Joe
 NewToHobbyKing 13323 points
Joe both work but I like the T6 Config.
VINAYAKA  2 points - 4/13/2014
 
What type of battery does the transmitter need?
 1stAidan 178 points
Eight AA batteries.
BEST ANSWER CREDIT AWARDED
 NewToHobbyKing 13323 points
Vin yes 8 x AAs Side by Side (Either one use or Rechargeable ). Turnigy AA Ni-ZN 1500mAh High Voltage (ready to use) (SKU: 91690000030 are great. Or you can go LIPO: Turnigy 1450mAh 3S 11.1v Transmitter Lipoly Pack (SKU: T1450-TX-3) will FIT!
JohnnyCanada  94 points - 4/12/2014
 
I've been using this transmitter for all sorts of projects over the last few years. Most recently along with the Turnigy v-tail mixer for my small 30" wing
 NewToHobbyKing 13323 points
JC that is the answer. Use her on only one model and then I would never of worn out my programing socket on the back. THANKS nice video!
 NewToHobbyKing 13323 points
OOPs but if you were using a 6 ch that would work too!
 JohnnyCanada 94 points
The 4 channel has no programming socket. As you said, the 6 channel does. You could use this one on multiple models by using the switches on the front to reverse channels where necessary. I have a 9x for most of my models and a 9xr I use for my FPV, but it's nice to have this one that I can throw in the car or lend to a buddy.
 NewToHobbyKing 13323 points
Yes I must Concur!
Customer Reviews
Overall Rating
Drew
205 likes
ValueUNRATED
QualityUNRATED
104 thumbs up!
Great product, easy to bind and great range/response.

just because some people were having trouble,

TO BIND:
1. connect the Rx to a Battery notice the blinking led
2. hold down the bind button on the bottom of the controller
3. turn on the controller while holding down the bind button and watch the led
4. when it stops blinking you are done (less than 5 secs for me).
3. t


12 comments. Reply..

Overall Rating
Robachan
962 likes
ValueUNRATED
QualityUNRATED
78 thumbs up!
1. Batteries in transmitter, switch off.
2. Connect one side of the bind plug to the BAT slot on the receiver.
3. Connect an ESC (with battery attached) to one of the channels. Black line (-) goes to the far right. You will see a red LED blinking.
4. Push and hold down the bind button on the transmitter while switching on. Keep the bind button held down until the red LED stops blinking. You are now ready to enjoy your wonderful new 2.4GHz TX.


4 comments. Reply..

Overall Rating
Customer
109 likes
ValueUNRATED
QualityUNRATED
78 thumbs up!
After a range test the club members were impressed by its performance. Hand signals to confirm its function were hardly seen on the end of the test so we stopped it. No servo-vibrations were noticed during this test so the signal stayed clear overall. The 3 test flights afterwards only confirmed the first experiment. Five stars for doing its job but what a pity no instructions are available.
Very pleased with this purchase.


1 comment. Reply..

Overall Rating
Topcad
191 likes
ValueUNRATED
QualityUNRATED
24 thumbs up!
To Bind this transmitter use this manual and it works good i found it and it is the seem product as the Hobby King 2.4Ghz transmitters

this is the www.link Topcad


3 comments. Reply..

Overall Rating
Buggs
27 likes
ValueUNRATED
QualityUNRATED
14 thumbs up!
Awesome price! I love this radio and I also got 2 extra receivers. I am flying indoor and the receiver case can be easily removed to save weight. I also have another 6ch USB computer radio that binds to these recievers and workd with all 6 channels. Hobby City needs 6ch mixing version.


2 comments. Reply..

.....click here to see all reviews
Aff. Link