Please confirm your location:



USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Electric Motors > Outrunners by size
> Electric Motors > Outrunners by size > Bell Type

  RATED:

hexTronik DT750 Brushless Outrunner 750kv

hexTronik DT750 Brushless Outrunner 750kv

Looks can be deceiving. This outrunner is around twice the size of a towerpro bell motor, and swings a much larger prop. Its the motor used on some of Art-techs new plane kits, which is testiment to its durability, ease of use and quality.
The DT700 will swing an 11x4.7 SF prop nicely, to produce more than 900g of thrust.
Its great for larger GWS foamies or parkfly planes.

Spec.
Required Voltage: 11.1v
Suggested Battery Capacity: 1300mAh +
Suggested Prop: 11x3.8 or 11x4.7
Max current draw: 18A (with 11x4.7 prop)
Max thrust: 1000g+
No Load Current: 1.4A
Shaft: 4M (perfectly suited to Towerpor/GWS SF Slow Fly props)
Weight: 78g
Diameter: 41mm
Overall length: 77mm
Kv: 750rpm/v
Comes with mount as shown in Image

Test Report.
We used the DAT700 outrunner to power the an Art-tech Pitts. Run with a 1300mAh 3S1P 20C pack, 18A BESC and 1147 GWS/Towerpro prop, the Art-tech pitts ran nicely. Excellent climb rate, though not hoverable, and with 13minute flight times or more, we were very impressed.
A very efficient outrunner for slower flying models of up to .15 size.



PRODUCT ID: DT750

This product available from a warehouse near you!

Kv(rpm/v) 750
Weight (g) 78
Max Current(A) 18
Resistance(mh) 0
Max Voltage(V) 11
Power(W) 0
Shaft A (mm) 4
Length B (mm) 37
Diameter C (mm) 40
Can Length (mm) 10
Total Length E (mm) 77
Update/Add my own data
Customer Data

Weight: 79g
Quantity: 
International Warehouse
stock
10+
USA West Warehouse In Stock View Item
USA East Warehouse In Stock View Item
Price  $13.65

Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
5213
crowns
  
 
Total of 384 discussions.
ferdovs  5 points - 4/19/2015
 
Hallo, Can I use 7.4 Prop with this Motor ? than u
 ferdovs 5 points
I mean 7x4
Dave Drone flier  3 points - 4/16/2015
 
I use 20amp Afroslim ESC. Tried 2450mAh 3S 25C, 3600mAh 3S 40C and Multistar 5200mAh 3S 10C All works no problems with this motor with a 10x4.5 prop. I tried a 11" prop but they had very bad vibration so I switched back to the 10" . Its enough to lift quite a bit of weight with my tricopter so your quad should have no problems.
bernardo  1 points - 4/10/2015
 
what battery/esc should i use if i want to make a quadcopter with these motors?any suggestions would be appreciated!
 VQuad_nl 4 points
I use Turnigy Plush 25A ESC's, and a 2200mAh 3S 25C. Works fine, plenty of power, and ESC's or motors don't even get hot.
Abdullah  29 points - 3/11/2015
 
Where can i find mounts for this model?
 Alexey Dmitrievich 1 points
What kind of mount you mean? Black round mount as on the picture goes in a set
 Callum 44 points
there is a mount on the motor (that plastic black base). You can just screw or zip tie it down.
ARISTIDIS  1 points - 3/10/2015
 
Hi ! My plane is a trainer 750grams it is compatible with a 20A speed controller, 2s 7.4 180mah Lipo.... It will flow and what prop adapter I can use ? Please help me ..,,also I have gws 1047 proppele....
 Devin 9 points
1800mah sure. Not 180mah. Too small. Best to use 850mah high c rating and above.
 Callum 44 points
you can use M3 nuts for the props. or cut the motor shaft down and fit a prop saver.
Customer Reviews
Review Blogs for this item
HexTronic DT750 in the test bench
Jan A
Overall Rating
DAVID M NORTH
likes
ValueUNRATED
QualityUNRATED
50 thumbs up!
Because of the price and reasonably accurate description, I'll give it five stars. Modest 8mm (!) bearing tube and bearings don't sound all that great, but the power efficiency is pretty darn good if you can carry the nearly 3oz weight.

For example, a 10x4.7 APC SF plus TP 1320 3S produced about 34oz thrust using 13.96 amps. Both Drive Calculator and Badcock's web page put this as 84-86pcnt efficient. 11x4.7 APC Sf produced over 40oz thrust for a bit over 17 amps. That's still very good efficiency!

Again, if the weight and 4mm screw shaft don't scare you, it will definitely pump out the stuff even if it sounds a bit like a coffee grinder. Added bonus: very nice motor mount that will work great with your MicroDan.


9 comments. Reply..

Overall Rating
Sascha Fritz
likes
ValueUNRATED
QualityUNRATED
27 thumbs up!
This are the results of my test, measured with my eagel tree:

11 x 7 GWS HD (not the slowfly version)
peak: about 13.5 A
after 20 sec about: 12.0 A
on 3 S with on 10.5V

11 x 4,7 GWS
peak: about 15.0 A
after 20 sec about: 13.0 A
on 3 S with on 10.4V

12 x 6 GWS HD (not the slowfly version)
peak: about 15.0 A
after 20 sec about: 13.0 A
on 3 S with on 10.4V

I couldn't measure trust but from my feeling the trust with 11x4,7 and the 12x6 are nearly the same. The speed with the 12x6 is higher. This will be my choice.

I will put the motor into my selfmade Extra with about 700g, I hope it is a good choice.

I think the motor could spin a bigger prop, next time I try the GWS 12x8 HD and the GWS 11x8 RS.

I don't no if I have get a lower Kv version. I read in the rcforum about measurements which are close to Davids.


4 comments. Reply..

Overall Rating
Robert Pacheco
likes
ValueUNRATED
QualityUNRATED
18 thumbs up!
Wow. This motor is such a great value. It pushes my 2lb Das Ugly Stik around with authority. I got 34oz thrust with 11.1v 20c 1600 Lipoly and 11X7 SF APC prop. This puts me into larger RC planes at a modest cost.
**Neons** Bob


2 comments. Reply..

Overall Rating
Shawn Anderson
likes
ValueUNRATED
QualityUNRATED
18 thumbs up!
I think Dave got a dodgy motor because mine doesn't make any grinding noises at all. I don't know if I'd call it completely silent but it's no louder than any other outrunner of this size. And while I haven't tested my motor yet I do trust Dave's numbers post above. So, it's cheap, quiet and very efficient. And all for under $11. A bona fide bargain in my book.


2 comments. Reply..

Overall Rating
FOKKER DVII
likes
ValueUNRATED
QualityUNRATED
13 thumbs up!
Bought this for my Lanier Fokker biplane.
It is a good motor for this slow-flying WWI bird.
With this motor and APC 10*3.8 prop., the Longmax 1300 3S Lipo doesn't get hot and not even warm after 6-7minutes flight.
For this price, I like it very much!


8 comments. Reply..

.....click here to see all reviews
Aff. Link