Turnigy 5mm Heat Shrink Tube - RED (1mtr)

 Andreas 95 points

Because they are sold?

 Herman 38 points

Yes. But it's a little weird that every single kind of them are sold out.

 David 2 points

Any date of resupplying ?

 Andreas 95 points

No, but i think thay will be back in stock soon *-)

 Hussain Joharji 204 points

because it is helpfu of course :) .. the most importatnt thing is that it in stock now ... :)

 Giovani 22 points

because it is a very good product and has a lot of output, so it is recommended to buy a larger quantity and store not to run out!

 sharkey9 792 points

It should be fine.

 NewToHobbyKing 6341 points

Mark yes if you are only fitting 3.5mm bullet connectors. Anything 3 to 4mm it is great for.

 Blue__Rocket 63 points

won't fit!!! Far to small!

 NewToHobbyKing 6341 points

Yes far to small to fit over the whole ESC but fine for the Esc to Motor connectors. Also on for the other end to the battery.

 Andreas 95 points

? What is this for?

 Blue__Rocket 63 points

Was a buddy code. It was deleted... Unfortunately.

 NewToHobbyKing 6341 points

Well it is as long as you have spare grams in your shipment. I you are only buying 1m and nil else the price goes up a LOT. It's base price is great!

 __nayr 51 points

i tried mine on hobby kings servo connectors and the shrink sleeve is to small. the male servo connector hobby king sells is 7mm wide and 2mm thick

 abdulahad100 363 points

No. A servo connector will not fit through this. You will need a 10mm heat shrink (PRODUCT ID: WHS10-RED)

 AeroEscolaFly 86 points

It will enough if you take all the small steel conector from the plastic in order to pass them through the heat shrink tube. I use a small needle to take them from the plastic.

 Nathaniel 7 points

I agree you should definitely use the 10mm heat shrink

 billum2 172 points

Only if you remove the pins from the housing and replace after pushing the wires through the heatshrink.

 tianshuang 2 points

No, this is too small for the servo connector, you may want to try 10mm one.

 tobias 13 points

no, you have to buy a bigger one!

 Marc 1 points

tke the 6mm

 Andrej 8 points

no, take bigger

 MPSAMPA01 5 points

no, need bigger

 shahwaiz 33 points

Try to use a gas one the ones used for cigars they don't spoil it.

 nguyentran 21 points

yes.i dont own a heat gun and as such i always shrink it with lighter. but make sure you dont keep burning at one spot, keep the lighter a bit further away and move around so the heat is distributed evenly

 Nathaniel 7 points

If you use a cigar type lighter make sure to move it around evenly or you could burn a hole in the tubing

 tobias 13 points

yes it will work, i always shrink it with a lighter

 PeepsDayz 18 points

Use only the blue part of the flame, yellow will burn it. Hope this helps

 Timymimus 44 points

after shriking it will be around 2.5-3.5mm

 Kellyann 16223 points

DerDepronTyp after the shrinking 3mm. I hope this helps.

 MP3_tilaco 26 points

encoje a la mitad del diametro original.

 okie_1 11 points

most all heat shrink tubing will shrink to approx. 1/2 of it's original size

 LUNDY 282 points

It depend's on how much heat you gone use,if you have a hot air blower of 1500 Wath and go close to the object the tube will shrink to about 2mm to 2,5mm add the heat bit by bit not a full blast of hot air in one time is giving the best results . If you use a lighter, you are burning the shrink tube and damage it use a good hobby hot air gun.

 Richard 15 points

If you use to much heat it will split. other than that it works very well.

 Dillzio 403 points

2.5mm after shrinking. Perfect size for terminals on XT-60 plugs.

 Angelo 1 points

Use 5mm. Is suficient.

 henry 4 points

it shrinks half its size and is perfect for most connectors you can also stretch it out with a pear pliers put them in the middle then open them

 Vulture231 59 points

It will shrink to the size of the connector/wire inside the heat shrink tube with a minimum of 2 or 2.5 mm. Electronic stores have shrink tube that shrinks a factor 3.

 Kirill 72 points

General rule of thumb is: the shrinking tube shrinks to 2/3 of it's original diameter.

 luigi 9 points

just 2 or 2.5

 AeroEscolaFly 86 points

2.5 mm diameter after shrinking.

 Roman 252 points

Kvalitní dobre zpracovatelná samosmrštovacka.

 futurebreeze 35 points

It is the diammeter.

 Rinaldo Salmazo 9 points

The 5mm is the diameter. After you warm up it, it gets 3mm.

 Kellyann 16223 points

Rinaldo thank you I got that from futurebreeze I wish I could reward more than one person Sorry.

 ThatNinthGuy 9 points

It's the before-heating diameter

 Richard 6 points

diameter before heating, will shrink to approx 50pcnt

 Uberfest 31 points

montei uma dessas em um bobcat com 2627edf, certamente o motor fica voltado para traz mais funcionamento é perfeito....

 slypo 11 points

It is the diameter NOT squashed flat.

 sciambola 1 points

è il diametro

 GUIX 5 points

top pour faire des montages propre.

 Josh 3 points

yah, the size before heat has been applied.

 Bas123 64 points

I think before?

 Jaromir 36 points

before.
after shrinhing about 40-60% of diameter before

 sweetstik 55 points

this is the PRE shrinkage diameter

 jmaja 55 points

before shrinking it - its 5mm.

 Tony_Pham 33 points

after shriking it will be around 3-4mm

 othmar 70 points

before *-)

 hakank 33 points

Before.

 regwojt 39 points

Before

 Dan 17 points

Before

 tnt jet 89 points

before shrinking!!

 Blaze4711 52 points

before shrinking

 Denyo 54 points

before shrinking!

 scott74dog 54 points

before

 __Riff 179 points

Before, after is ~2,5...3mm

 scott74dog 54 points

Before, they are 5mm big unshrunk

 Gehad 12 points

Theas are very nice never had problems with them i have ordered in many meteres very usefull

 lemmens 36 points

before shrinking

 Ludwig from DE 60 points

yes, before!

 SmartExpert 24 points

Mine "5mm" tube has a round inner diameter of 5.28mm before shrinking. They fit very well on "4mm gold connectors" wich have an outer diameter of 4.90mm. After shrinking the minimal inner diameter is about 2.60mm.

 Hady Esta 207 points

5mm before shrinking

 Jean-Luc 20 points

Before

 FRNFRN 139 points

Before

 danny 21 points

before

 brushlesspower 39 points

Before, it shrinks down to about 2-3mm.

 chapier61 169 points

Before, of course !

 Mike28 14 points

Hi, 5mm before shrinking!! Greetings

 thunderchicken 90 points

before

 chrisn 69 points

Before

 Davor 90 points

before

 buffmanmarc 38 points

Before shrinking.

 waldesbuehl 40 points

before

 Master_22 41 points

before !! *)

 Meehly 27 points

before shrinking

 hartley 68 points

5mm diameter before shrinking. will shrink nicely around 3mm wire. note 5mm diameter, NOT 5mm across when flat.

 MegaTesla 576 points

before

 HellyFlyer 1249 points

Before shrinking

 Leon 13 points

before

 Bartman493 24 points

This is 5mm before shrinking, good quality.

 Kai 17 points

before. At shrink i have used it with 1,5mm and it's perfect

 Kai 17 points

before. you can shrink it on a 2mm Gold Contact.

 Vova.St. 81 points

before!!!

 Wout.S 325 points

5mm before shrinking

 Marocco 88 points

5mm is before shriking, after shrinking it will be 2/3mm

 daniel 10 points

5mm before

 reduans 41 points

before

 vivazapata 20 points

It's 5mm BEFORE shrinking

 Alex B 9 points

Before shrinking

 Jordan 16 points

before

 The Rooster 19 points

Before shrinking

 math 10 points

before before schrinking it is 5mm