Please confirm your location:


USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Multi-Rotors & Parts > Flight Controller

  RATED:

Hobbyking KK2.0 Multi-rotor LCD Flight Control Board (US Warehouse)

Hobbyking KK2.0 Multi-rotor LCD Flight Control Board (US Warehouse)
Hobbyking KK2.0 Multi-rotor LCD Flight Control Board (US Warehouse)

Designed by the Grand father of the KK revolution, Rolf R Bakke, exclusively for HobbyKing, the KK2.0 is the evolution of the first generation KK flight control boards. The KK2.0 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft types are pre-installed. simply select your craft type, check motor layout/propeller direction, calibrate your ESCs and radio and your ready to go! all of which is done with easy to follow on screen prompts!

The original KK gyro system has been updated to an incredibly sensitive dual chip 3 Axis gyro and single chip 3 axis accelerometer system making this the most stable KK board ever and allowing for the addition of an Auto-level function. At the heart of the KK2.0 is an Atmel Mega324PA 8-bit AVR RISC-based microcontroller with 32k of memory. An additional 2 motor output channels have been added to the KK2.0 allowing for a total of 8 motors to be controlled (Octocopter). A handy Piezo buzzer is also included with the board for audio warning when activating and deactivating the board.

If your new to multi-rotor flight or have been unsure about how to setup a KK board then the KK2.0 was built for you. The 6 Pin USBasp AVR Programming interface ensures future software updates will be quick and easy.

Specs.
Size: 50.5mm x 50.5mm x 12mm
Weight: 21 gram (Inc Piezo buzzer)
IC: Atmega324 PA
Gyro: InvenSense Inc.
Accelerometer: Anologue Devices Inc.
Auto-level: Yes
Input Voltage: 4.8-6.0V
AVR interface: standard 6 pin.
Signal from Receiver: 1520us (5 channels)
Signal to ESC: 1520us
Firmware Version: 1.2

Here are some How-to Vids:

Part 1

Part 2

Part 3

Part 4

Part 5

Pre-installed firmware.
Dualcopter
Tricopter
Y6
Quadcopter +
Quadcopter X
Hexcopter +
Hexcopter X
Octocopter +
Octocopter X
X8 +
X8 X
H8
H6
V8
V6
Aero 1S Aileron
Aero 2S Aileron
Flying Wing
Singlecopter 2M 2S
Singlecopter 1M 4S
(Custom Mix via the "Mixer Editor" option)

The Mixer Editor allows you to adjust where and how much signal the motors receive from stick input and sensors. This allows you to create any configuration possible with up to 8 motors or servos.


Whats is a Multi-Rotor Control board you ask?


The HobbyKing KK2.0 Multi-Rotor controller is a flight control board for multi-rotor Aircraft (Tricopters, Quadcopters, Hexcopters etc). Its purpose is to stabilize the aircraft during flight. To do this it takes the signal from the three on board gyros (roll, pitch and yaw) then passes the signal to the Atmega324PA IC. The Atmega324PA IC unit then processes these signals according the users selected firmware and passes control signals to the installed Electronic Speed Controllers (ESCs). These signals instruct the ESCs to make fine adjustments to the motors rotational speed which in turn stabilizes your multi-rotor craft.

The HobbyKing KK2.0 Multi-Rotor control board also uses signals from your radio systems receiver (Rx) and passes these signals to the Atmega324PA IC via the ail, ele, thr and rud inputs. Once this information has been processed the IC will send varying signals to the ESCs which in turn adjust the rotational speed of each motor to induce controlled flight (up, down, backwards, forwards, left, right, yaw).

Note: A user manual is available under the files tab.
*Royalties paid on each unit sold to Rolf R Bakke, the original KK Designer.



PRODUCT ID: 9171000073


This is an archived page. This product is no longer available and has been replaced by a newer product.
CLICK HERE TO VIEW THE NEW PRODUCT


Weight: 55g
Quantity: 
USA West Warehouse
stock
BK
Price $30.68

Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
STOCK ARRIVAL ALERT

Enter your email address to get an email the second new stock arrives.
Estimated factory delivery date;
 Customer rated
510
crowns
  
 
Total of 187 discussions.
Daniel  1 points - 10/17/2014
 
I recently built an SK450 using this KK2.0 FC. I am using Turnigy 25A Hexafet ESCs. The craft flew fine many times. Recently broke it down and rebuilt it. The KK board if FRYING ESCs and MOTORS!!! What is going on??? I replaced all the motors and all the ESCs and double checked all polarity and solder connections and EVERYTHING. WHAT could be happening??? either the motor or the ESC decides to start getting crazy hot and smoke starts pouring out of it! The ONLY thing that I haven't changed is the KK board???????? Any help???
Diego Vera  14 points - 10/15/2014
 
Hi everyone, I hope you can help me, one of my motors does not work properly, it looks like does not want to spin same fast as the others, also If I try to stop it with my hands I can do it, others are impossible to stop with my hands because they work as expected, I already tried to calibrate my esc and nothing happens, I tried to replace the motor input from the board and looks that fix the problem for the broken motor but breaks the one I plugged in motor 1 kk2 input, that's why I assume esc, and motors are ok, but I don't know what can I do with my kk2, I'm really tired because I cannot fix it, does anyone here can help me please? thanks!
chuckk  5 points - 10/15/2014
 
where can I find the programs to update the KK2,1,5
Dave  41 points - 10/9/2014
 
With this board and the original firmware, I was flying my tri and lost sight when I took a wrong turn and crashed. It was working perfectly. Well, from all I could tell it hit the first motors arm and chipped off the ends of the blade. But now when I try to fly, it only spins in circles when I try to take off. Does anyone know if it damaged the gyros or some other internal parts ? I tried to reset the board and start over on the settings but I am not making it any better.. Any suggestions ? Thanks
Dave  41 points - 9/29/2014
 
Hi, Does anyone know where I can find the same firmware 1.2 since it is not displayed in the file above. When ever I tried to go to the lazyzero website and find the original firmware by KakpteinKuk it always shows error reading the device. But if I used the updated firmware by Stevies it copies fine. Is it the firmware or my usbsdp device bad.? Any way I just bought one from another site which I am shocked I found and has the older firmware which I feel is the best and most stable. Any help would be grateful. Thanks
Customer Reviews
Overall Rating
winginman
26 likes
Value
Quality
Like it?
I just finished setting up my second one of these on a quad. I have tried 3 other flight control boards and this is by far the best. Very stable with auto level on and very agile with it turned off. The setup using the LCD display is the way to go. You can change settings in the field without having to connect to a computer. Download the flash program and purchase the USB adapter and upgrade to the 1.5 or 1.6 version of the flash. The instructions are in the files section as well as the programs. Also check out RCGroups forum for additional tips. I followed the tutorial and it's easy.


No comments. Reply..

Overall Rating
__D308
52 likes
Value
Quality
Like it?
I purchased this unit for my dji f450. I did a fair amount of searching the web before I bought it. It was very easy to set up. I did have to tune it down a bit due to I'm a noob when it comes to multi rotors. I also have the f550 running the 3dr apm board. I like the kk2 better than the APm board. No flyaway and feels like I have control on the multi. It doesn't have all the cool stuff that the APM has but it's more reliable. I've shelved the f550. I don't trust it anymore. I fly the f450 with the kk2 almost every night. I don't think you will be discouraged if you are new and buy this board. It's a winner!!


No comments. Reply..

Overall Rating
chris
3 likes
Value
Quality
Like it?
I use this board for a multirotor, and also as a flight stabilizer, and camera stabilizer using OpenAero2. It has none of the GPS supported features, but aside from that, it is fantastic. I had high expectaions reading the reveiws, and once I figured out the details it has been a delight. I broke on board learning to fly my tricopter, but it was my fault. All that broke was the LCD screen because it took a direct hit. Even with the damaged LCD, it still worked just fine. There is a learning curve to making it work perfectly, but works reasonably well right out of the block. Be sure to upload the most current firmware, and it is even better.


No comments. Reply..

Create an account
Overall Rating
RC2211
361 likes
Value
Quality
Like it?
This is a preliminary review. This FC is super cheap and super easy to install, now I just hope it performs well! I will post another review with The KK2.0s flight performance.


No comments. Reply..

Create an account
Overall Rating
jaylevine
28 likes
Value
Quality
Like it?
I have purchased 4 of these boards and never had a problem getting any of them to work properly. They are so simple to use that it is hard for me to consider using anything else. If you want a no hassle flight controller, get one of these. There are many other boards that have more flexibility than this one, but if you just need a solid controller to fly around with a camera, this is the one for you.


No comments. Reply..

.....click here to see all reviews
Aff. Link