Please confirm your location:


USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Robotics & DIY > Arduino

  RATED:

Arduino Nano V3.0 Microcontroller Board

Arduino Nano V3.0 Microcontroller Board
Arduino Nano V3.0 Microcontroller Board

The Arduino Nano is a small, complete, and breadboard-friendly board based on the ATmega328. It has more or less the same functionality of the Arduino Duemilanove, but in a different package. It lacks only a DC power jack, and works with a Mini-B USB cable instead of a standard one.

The Nano 3.0 has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega328 provides UART TTL (5V) serial communication, which is available on digital pins 0 (RX) and 1 (TX). An FTDI FT232RL on the board channels this serial communication over USB and the FTDI drivers (included with the Arduino software) provide a virtual com port to software on the computer. The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board. The RX and TX LEDs on the board will flash when data is being transmitted via the FTDI chip and USB connection to the computer (but not for serial communication on pins 0 and 1).


*Note: This is not an original Arduino brand product, it is manufactured with the same components and functionality by a different manufacturer.


Specs:
Microcontroller: ATmega328
Operating Voltage (logic level): 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 14 (of which 6 provide PWM output)
Analog Input Pins: 8
DC Current per I/O Pin: 40mA
Flash Memory: 32KB (ATmega328) of which 2 KB used by bootloader
SRAM: 2KB (ATmega328)
EEPROM: 1KB (ATmega328)
Clock Speed: 16 MHz
Dimensions: 43 x 18 x 19mm
Weight: 6g



PRODUCT ID: 009000007

This product available from a warehouse near you!


Weight: 17g Quantity: 
International Warehouse
stock
0
USA West Warehouse In Stock View Item
Price $10.55

acc.
  • Arduino USB Cable

    Combo Price: $1.53   IN STOCK



Further discounts available for registered & logged-in customers.
STOCK ARRIVAL ALERT

Enter your email address to get an email the second new stock arrives.
Estimated factory delivery date;
 Customer rated
423
crowns
  
 
Total of 39 discussions.
Nir  1 points - 8/17/2014
 
I have the same RESP=0x00 problem. I got 8 arduino nano units, all with the same problem. I tried both with arduino 1.0.5 and 1.5.7 beta. I have a new PC, windows 7 64Bit. When i connected a unit for the first time, the driver was installed automatically. When I try to update the driver to the driver on the arduino's library, I get a message "Windows already installed the latest drivers for this device". What can I do to be able to work with my devices?
Adrian  5 points - 7/21/2014
 
Nano on Win 8 problem solved Needs to use _older_ FTDI drivers: 2.8.24.0 4/10/2012
 Gerry01 4346 points
Adrian, thanks for sharing it, I still have w7 but I'll be using a new computer soon with this.
Adrian  5 points - 7/11/2014
 
I can’*t get my Nano to talk to my Win 8.1 laptop, the infamous: avrdude: stk500_getsync(): not in sync: resp=0x00 No problems with my Uno board and this laptop. The Nano will talk to my Mac OSX box. I started with standard Arduino install and have since upgraded drivers as noted below Arduino 1.5.6-r2 Device Manager: Ports (COM & LPT): USB Serial Port (COM8) Status: This device is working properly Driver FTDI 2.10.0 1/27/2014 Device Manager: Universal Serial Bus Controllers: USB Serial Converter Status: This device is working properly Driver FTDI 2.10.0 1/27/2014 Any suggestions would be much appreciated!
Herbert KC  4 points - 5/11/2014
 
Many thanks Dries, it works great. It works on my 32 bits laptop, how about on 64 bits? Have try those files loaded here but sad to say it doesn't work. Appreciate all help and advice. Thanks again.
 r_g_r 1288 points
I'm running Win7 64bit and I use Arduino IDE 1.0.5r2 without problems. Just note that you need to install two drivers for the Nano (only one driver needed for the Arduino UNO). When I first plugged the Nano a new device was detected but driver auto-load failed. I opened the device manager and clicked the device and selected update software, then manually choose the path to the drivers folder in the arduino IDE installation. After this first driver is installed a new device pops up in the device manager. No do the same, select update driver and manually point to the drivers directory. Now you should have some COM-Port device. You need to switch your IDE to that COM-Port.
Herbert KC  4 points - 4/23/2014
 
Hi, all selection is correct. It seems as there is a driver issue. The com port detect the uno board once it was plugged in. As for nano v3, it took very long to detect it. Do you have the driver for nano? Or could you help by telling me where to get it. Thanks.
 Dries 2 points
Finally got my Arduino nana v3.0 to work make sure that port driver is ver.2.8.30.0 with driver date 2013/07/12 and check under Universal serial bus Controller for USB serial Converter this Driver should be 2.8.14.0 Driver Date 2011/08/11 .All drivers came with Arduino software. hope this will solve your problems
Customer Reviews
Create an account
Overall Rating
flyandi
920 likes
Value
Quality
Like it?
Ahh I wish those are back in stock. This is the same as the Nano but without the heavy price. I run a full camera control on this chip and it works Aplusplusplusplus! Thank you HK for bringing the Arduino World to us!


1 comment. Reply..

Overall Rating
SAMolzen
13 likes
Value
Quality
Like it?
The three Nano's I bought all work perfectly. Great value. Very good quality soldering and build. I have them talking to one-another via I2C. Great stuff! : )


3 comments. Reply..

Overall Rating
Igor Zhydanov
8 likes
Value
Quality
Like it?
www.link Ардуино для www.link www.link на моделях www.link www.link


No comments. Reply..

Overall Rating
mikeythev
21 likes
Value
Quality
Like it?
These are totally worth the money. I've used the Duemilanoves for a few years and now I want to go smaller. These nanos plug in nicely to any standard breadboard, and program just like any other "duino" product. I purchased two and both are working great. I'm using these with students in an electronics course and they enjoy the ease of a breadboard-ready product. I've driven servos with the PWM, blinked LEDs, and transmitted analog and digital signals over the serial line. Nice work HobbyKing.


No comments. Reply..

Create an account
Overall Rating
Andry_
39 likes
Value
Quality
Like it?
?????? ??????? ??? ????????.
??????.


No comments. Reply..

.....click here to see all reviews
Aff. Link