Please confirm your location:

Arkansas warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the Arkansas warehouse even better value!
  Item found in the following categories;
> Batteries & Accessories > Li-Poly (All brands)
> Batteries & Accessories > Airsoft Batteries
> Airsoft & Accessories > Lipoly Batteries


Turnigy nano-tech 1400mah 3S 15~25C Lipo AIRSOFT Pack (US Warehouse)

Turnigy nano-tech 1400mah 3S 15~25C Lipo AIRSOFT Pack (US Warehouse)

When it comes to putting rounds down range, no one wants to compromise on fire power! thats why the legendary Turnigy nano-tech batteries are now available for Airsoft combat. Higher motor RPM, less voltage sag and extended operating times equal better performance from your weapon of choice.

The nano-tech Airsoft series also feature 5C charge ratings putting you back on the front line faster!

Get an unfair advantage and make sure your opponents know that they have been taken out by nano-tech!

Capacity: 1400mAh
Voltage: 3S1P / 3S Cell / 11.1V
Discharge: 15C Constant / 25C Burst
Weight: 115g (including wire, plug & case)
Dimensions: 128x7x20mm (Each)
Balance Plug: JST-XH
Discharge Plug: Mini-Tamiya (Mini Molex)

The nano-core technology in lithium ion batteries is the application of nanometer conductive additives.

 1) The nanometer conductive additives form ultrastrong electron-conducting networks in the electrodes which can increase electronic conductivity. 2) These additives create a superstrong ability for imbibition in the carrier liquid to supply more ion channels. This improves the ability of ion transmission and ion diffusion. Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.

Advantages over traditional Lipo batteries:
-Power density reaches 7.5 kw/kg.
-Less Voltage sag during high rate discharge, giving more power under load.
-Internal impedance can reach as low as 1.2mΩ compared to that of 3mΩ of a standard Lipoly.
-Greater thermal control, pack usually doesnt exceed 60degC
-Thickness swelling during heavy load doesnt exceed 5%, compared to 15% of a normal Lipoly   during heavy load.
-Higher capacity during heavy discharge. More than 90% at 100% C rate.
-Fast charge capable, up to 15C on some batteries.
-Longer Cycle Life, almost double that of standard lipoly technology.

*The length of balance charging wire may vary


Capacity(mAh) 1400
Config (s) 3
Discharge (c) 15
Weight (g) 115
Max Charge Rate (C) 5
Length-A(mm) 128
Height-B(mm) 20
Width-C(mm) 7
Update/Add my own data
Customer Data

Shipped from:
USA West Warehouse



  • Graphene Velcro Battery Strap 200mm (US Warehouse)

    Combo Price: $2.49   IN STOCK
    Add to Cart

  • MultiStar Velcro Battery Strap 300mm (US Warehouse)

    Combo Price: $2.15   IN STOCK
    Add to Cart

  • MultiStar Velcro Battery Strap 200mm (US Warehouse)

    Combo Price: $1.94   IN STOCK
    Add to Cart

Further discounts available for registered & logged-in customers.

Enter your email address to get an email the second new stock arrives.
Estimated factory delivery date;
 Customer rated
Total of 2 discussions.
travis  6 points - 5/2/2014
how is it that I am pulling 47 amps out of this? 35 should be the max...
 Alex 1 points
You can pull a whole lot more out of the battery actually* maybe up to and over 60 amps on a short circuit. The battery would die very quickly however and doing so would not be a safe thing to do. The 35 amp maximum rating is there to let you know, that pulling more than 35 amps out of the battery, you will damage it. The load will draw precisely as much current as it needs. From the way things sound, this battery is under powered for your application.
ATLOO1  1 points - 6/18/2013
Does anyone have experience with fitting this in a kwa or similar mil spec aeg buffer tube?
Customer Reviews
Overall Rating
Like it?
Quite the little punch from such a small lipo. I ordered both this, and the 1200mah version of this 3s lipo. The only major difference is a VERY slight, and almost unnoticeable thickness difference. I would opt for this lipo. Uses: Light-moderate upgraded AEGs. If your smart you'd use this lipo in an efficient setup. This rips when paired with a decent AEG, but SHINES when used with a fine tuned gun. This being a lipo, I'd recommend, as I always do when it comes to airsoft replicas and lipos, to invest in a Mosfet. The best mosfet units are actually the hand made ones by people whom know what they are doing, at the time of this review I recommend any unit using the IR3034. Fitment: Yes, this fits perfectly in Crane stocks. Two cells on one side, and another on the other. There is ample wire, so when you do change the connector to Deans or TX60, I'd recommend shortening the wires. That is preference however. I've also had success fitting these in pretty much every AEG I've tried it with. That includes all types of G36, M4s, Mp5s, etc etc. Very versatile battery pack. Performance: With an average AEG with an M120 expect solid 20-25RPS, depending on your setup. A tuned AEG can push 30 it all depends on your setup. Being a tech for 6 years I am very confident that this pack can and will meet your needs and expectations. Extra notes: I personally use this as my go to pack

No comments. Reply..

Overall Rating
Like it?
(continued) for tight fitting AEGs. To date, the most extreme setup I have is inside my PDW's rail (After much, MUCH modification) so almost anything is possible. If one had the time you could easily cut and dremmel material to fit inside any rail system. In said PDW, I've ran it 25-30RPS at 360FPS no problem, however I'm currently finishing a DSG build that includes a riot spacer'd SP150 and Lonex titan A2. These should put me at 40-50RPS @ 400FPS if all goes well. I will post another review to see how this little pack handles that setup! Overall, HIGHLY recommend pack!

1 comment. Reply.. here to see all reviews
Aff. Link