Please confirm your location:

Arkansas warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the Arkansas warehouse even better value!
  Item found in the following categories;
> Speed Controllers (ESC) > All Speed Controllers (ESC)
> Speed Controllers (ESC) > TURNIGY ESC
> Speed Controllers (ESC) > 20 to 39 Amp
> Multi-Rotors & Parts > Speed Controller (ESC) > Turnigy Plush


TURNIGY Plush 25amp Speed Controller

TURNIGY Plush 25amp Speed Controller

Plush 25 Brushless Speed Controller
The Plush series ESC are a very good quality controller. They have a broad range of programming features and a smooth throttle response compared to other BESCs in the same price range.

Our TURNIGY speed controllers come with a 14 month warranty. We guarentee these are the best Brushless Speed Controllers you can purchase at this price.
These speed controllers are sold in western countries under various names at tripple the price.
We are certain you will find these to be the best BESC available from Asia.

Cont Current: 25A
Burst Current: 35A
BEC Mode: Linear
BEC : 5v / 2A
Lipo Cells: 2-4
NiMH : 5-12
Weight: 22g
Size: 24x45x11mm
Supported motor speed for all TURNIGY ESCs is;
(Maximum): 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).

User Programmable, both via controller and optional programming card. The programming card is an excellent item as it instantly tells the user the current settings and with a few simple clicks of the buttons, the user can change the settings and have graphical reassurance of those changes.
The programming card is an excellent Item and simple to use!


Weight: 47g
International Warehouse
USA West Warehouse In Stock View Item
USA East Warehouse In Stock View Item
Price  $13.45

Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
Total of 200 discussions.
James  1 points - 9/24/2015
I recently built another foamy and installed the Turnigy Plush 25A running a Propdrive 28-26 1200KV motor. The reciever I am using is an Orange R620. With this setup the servos for rudder, aileron, and elevator does not return back to center after movement to full extent. Example if I turn left it will center ok, but turning right it is a little right of center each time. Changing servos did not fix it. So, I changed the ESC out with one from another plane and everthing is centering correctly. Put the Plush 25A back in the plane, problem centering returns again. I think there is a problem with the ESC. It causes a lot of control issues. HELP!!
 anikeev 1407 points
ESC can cause this when servos take too much power, or when something is wrong with electronic fields. You can try to mount RX as fas as possible away from ESC. You can also screen all servo wires with foil.
ken  74 points - 9/11/2015
does this have a yellow xtc battery connector,thanks
 anikeev 1407 points
This ESC comes without any connectors. You need to buy some bullets to connect motors and some XT60 or whatever to sonnect it to the battery. That requires soldering skills, of course.
Dion  3 points - 8/24/2015
When they say user program "by controller", what does that mean? Will I need any other peripherals to program?
 EricBR 404 points
it means that you can program the esc using the sticks on your radio transmitter. you start with the throttle stick to the max, plug the battery to the esc and wait for specific beeps.
 anikeev 1407 points
You can use specific program board that will show all settings with LEDs. The board lets you program ESC more easily and obviously but it works only with specific ESCs. I can't find any programming card designed for Plush-series. But you still can program it with your transmitter. When you buy this ESC you'll get a paper card where all programming scheme shown.
 craig 1 points
you didn't look very hard did you!
David  3 points - 6/22/2015
Do these ESC's come with any connectors soldered onto them?
 BuBu1 317 points
No, as I remember they come with no connector at all. You have to solder your own connectors on both sides.
 anikeev 1407 points
It comes in semitransparent grey antistatic bag with manual papercard inside. No connectors provided - you need to buy your own.
Francois  1 points - 6/1/2015
Bonjour, Quel est le diamè*tre des câ*bles d'alimentation et - svp? Franç*ois.
 anikeev 1407 points
Diameter 12-14AWG (2mm-1.6mm). Je ne me souviens pas.
 anikeev 1407 points
Il é*tait un fil. Hors isolement.
 Francois 1 points
Ok, thank you very much.
Customer Reviews
Overall Rating
27 thumbs up!
I hooked my 25A Plush up to a 3s 2200mAh Zippy & Turnigy C2830 brushless outrunner and the ESC doesn't beep, doesn't start the motor, nothing. I can move the servos that are connected to the Rx, but I can't get any throttle response or the beeping that the manual references. Any thoughts on how to get my motor going, or why the ESC isn't beeping?

18 comments. Reply..

Overall Rating
William Thesing
20 thumbs up!
The newer version includes another plug which will connect to the charge port of your Lipo for pack monitoring (low voltage protection). This is not shown in the photo. It is not mandatory to connect this. Unfortunately I cannot use these in my GWS 38 due to the size and extra . I will reserve this pair for other projects or replacement in existing planes. The photo should be updated, as the extra wiring causes more space limitations and should not be cut off.

5 comments. Reply..

Overall Rating
20 thumbs up!
I bought 2 of these to put into 2 HK450 Heli's with KD KA450H motors and Zippy 3s 2200 battery. One smoked on the first flight. The other has been performing perfectly. It was very easy to program with the programming card that Hobby City also sells. I think I just got one that was a dud.

8 comments. Reply..

Create an account
Overall Rating
20 thumbs up!
good esc but some problem with programmable option. sometimes it's reset or don't power up in proper condition.

1 comment. Reply..

Overall Rating
17 thumbs up!
This esc is really good. Compared to other china-made esc is really much better. Lots of very useful programmable options. Better throttle curve etc.

On the other hand it has a little problematic startup with my motor POT 200W. I tried every possible setting, but even with the one with best results i crashed due to the fact that motor went out of synchronism with esc. Czech made esc i used before were always ok.

2 comments. Reply.. here to see all reviews
Aff. Link