Please confirm your location:

Arkansas warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the Arkansas warehouse even better value!
  Item found in the following categories;
> Electric Motors > Outrunners by size > 28 to 34mm
> Electric Motors > TURNIGY SK3 > 28mm


Turnigy Aerodrive SK3 - 2822-1090kv Brushless Outrunner Motor

Turnigy Aerodrive SK3 - 2822-1090kv Brushless Outrunner Motor
Turnigy Aerodrive SK3 - 2822-1090kv Brushless Outrunner Motor

Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.

The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.

Turns: 50T
Voltage: 2~3S Lipoly
RPM/V: 1090kv
Internal resistance: 0.235 Ohm
Max Loading: 7A
Max Power: 80W
Shaft Dia: 3.0mm
Bolt holes: 16mm & 19mm
Bolt thread: M3
Weight: 31g
Motor Plug: 3.5mm Bullet Connector


PRODUCT ID: SK3-2822-1090

Kv(rpm/v) 1090
Weight (g) 31
Max Current(A) 7
Resistance(mh) 235
Max Voltage(V) 11
Power(W) 80
Shaft A (mm) -
Length B (mm) 21
Diameter C (mm) 28
Can Length (mm) 8
Total Length E (mm) 33
Update/Add my own data
Customer Data

Shipped from:
International Warehouse



  • T-Prop Adaptor Set for SK3 Motors (Direct Bolt)

    Combo Price: $8.76   IN STOCK
    Add to Cart

  • Turnigy Aerodrive SK3 2822 Series Replacement Shaft Set

    Combo Price: $0.86   IN STOCK
    Add to Cart

  • Turnigy Aerodrive SK3 - 28-XX Spare Accessory Pack

    Combo Price: $4.28   BACKORDER
    Add to Cart

Further discounts available for registered & logged-in customers.
 Customer rated
Total of 30 discussions.
Austin  3 points - 5/25/2016
(New to the RC world) Any suggestions on a prop for this? I'm building a replica that would work perfect with a 3 inch prop, but any suggestions would be helpful.
VERHAEGHE  16 points - 4/12/2015
Hi, Can I use this motor in 4S ?
 Abhilekh 261 points
yes, I have tried it in my Dualcopter with 4S. But the prop size was reduced. It works fine.
Sandro  2 points - 11/13/2014
Hi the motors arrives with the accessories in the second photo or I have to buy the spare accessory pack separately?
 Anthony 61 points
Yes, and a nice little box too. :)
bstarkey54  10 points - 9/2/2014
Any suggestions for a airplane for this motor?
 Björn 40 points
PRODUCT ID: 9420000003-0
bstarkey54  10 points - 9/2/2014
Any suggestions for a airplane for this motor?
Customer Reviews
Overall Rating
Like it?
The engine is manufactured in a good quality! All in all a satisfactory product. Price performance is top! The screw propeller holder is attached with three screws 2M. The gap between the stator and the bell is small and the detent torque is low - normal for a 14 pole motor with 12 slots. The cables of the phases are not enamelled copper wire, 20-24 AWG wire instead. Great for soldering. I run the engine in a 8x4, 5 prop with a 12A blue HK series with a 3S lipo - without any errors. cu

1 comment. Reply..

Overall Rating
Blue Angel
Like it?
Very nice little motor. It is a comparable motor to the KDA 20-50S. 33g with 2mm gold connectors and the prop holder (fixed with 3 screws). The 3 screws are not the best quality, so don't screw them too strong, or the winding will break. I have measured this motor (and the KDA 20-50S) with my Eagletree gear and uploaded the data to drivecalc. You can use this program to try different props. and find the right configuration. (Turnigy SK3 2822-1090 - timing high) perfect motor for small quadcopters: measured for example following combination: Turnigy Plush 10A Maxx Pro. EPP0845 Prop. Voltage: 11,15V Current: 8,30A RPM: 7132 thrust: around 425g

1 comment. Reply..

Create an account
Overall Rating
Like it?
vraiment tip top ses moteurs,
un ptit bemol, les 3 phases ne sortent pas toujours du même côté par rapport au fixation du moteur. Ou ptète la faute à pas d'chance

No comments. Reply..

Overall Rating
Like it?
Bought 2 pcs, but only bench tested them so far: 7.4Amps at 10.4Volt (semi charged 3S LiPo) with 8x4.5" prop. Quality seems fine.

No comments. Reply..

Overall Rating
Like it?
These motors where what I used for a quadcopter build a year ago and lets say they are a great choice. Flight time wise, I'm flying around 10 mins with a 0845 prop, 3s 2200 mah lipo, and 10amp escs. These motors are great for the price, they do get a little bit warm but not close to hot. As for build quality, there is nothing to complain about except that one of the motors did get bent from a 25ft fall, as the bottom plate (the plate from where the shaft protrudes) seems to be the weakest part of the motor but then again it was 25 feet. These motors are Over all, I will buy these motors again as they are cheap, preform well, and look good on my quad. Note-If you are going to get this motor, get some higher rated esc's because my 10 amp escs do get fairly hot, even at winter time.

No comments. Reply.. here to see all reviews
Aff. Link