USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Electric Motors > TURNIGY SK3 > 63mm
> Electric Motors > Outrunners by size > Above 50mm


Turnigy Aerodrive SK3 - 6374-192kv Brushless Outrunner Motor

Turnigy Aerodrive SK3 - 6374-192kv Brushless Outrunner Motor
Turnigy Aerodrive SK3 - 6374-192kv Brushless Outrunner Motor

Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today. The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time. The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise. Specs.Turns: 14TVoltage: 10~12S LipolyRPM/V: 192kvInternal resistance: 0.016 OhmMax Loading: 80AMax Power: 2750WShaft Dia: 8.0mmBolt holes: 32mmBolt thread: M4Weight: 858gMotor Plug: 4.0mm Bullet Connector

PRODUCT ID: SK3-6374-192

This product available from a warehouse near you!

Kv (rpm/v) 192
Weight (g) 858
Max Current (A) 80
Resistance (mh) 16
Max Voltage (V) 44
Power(W) 2750
Shaft A (mm) 8
Length B (mm) 86
Diameter C (mm) 59
Can Length D (mm) 61
Total Length E (mm) 113
Update/Add my own data
Customer Data

Weight: 1288g Quantity: 
United States Warehouse In Stock View Item

  • Turnigy Aerodrive SK3 - 63-XX Spare Accessory Pack

    Combo Price: $5.76   BACKORDER

  • Turnigy Aerodrive SK3 6374 Series Replacement Shaft Set

    Combo Price: $4.85   BACKORDER

Further discounts available for registered & logged-in customers.
 Customer rated
Total of 17 discussions.
KajoTheAfro  2 points - 2/19/2014
Hello...I need the right measures of the adapters ...I have a spinner that uses a 4mm bolt that I want to use with this engine...tx a lot,best regards
visioneer_one  104 points - 2/4/2014
FYI all of the listed specs are incorrect. I just measured mine - the bare motor is 82.4mm long and 877g, motor bolt-on adapter and X-mount is 95.5mm long and 941g.
Amos  19 points - 1/7/2014
What timing to use normal or high ?
 thomas 2 points
Hard to answer without knowing the weight and gearing\prop you are using but generally Start with low\normal timing and move up if the motor get hot or seems to cog at low speed then move the timing back down. Lower Timing = Torque Higher Timing = Top end power and speed
 thomas 2 points
Lower Timing = Torque
Higher Timing = Top end power and speed
 Amos 19 points
Hi I conect the motor to hk 150A car esc on electric skateboard. With 6s 5000 40C (bit old) I can not clim the road 6 deg on full throtle(I get cell protection cutoff). I can climb the road with 60% throtle with normal timing. So if I will lower timing I will have more Torque ?
 thomas 2 points
What ESC are you using i have this motor on a electric skateboard and can go up 10-12 percent grades easily. I would be suspect of the battery. I am running a 6s 7500mah setup
Carl  2 points - 12/5/2013
Looking to put this on an e-scooter. Can someone suggest what ESC and batteries I should use? Would I need anything else besides batteries, esc, and the motor? Thanks
 Brussless 25 points
you need a servo/motor regulator tester to control the speed
 Amos 19 points
Hk 150a car esc. Chain sprokets. Motor mount. Battrry depened on your need but you need 6s 5000mah at least for about 10 minutes
Gabe  9 points - 8/31/2013
hi, can any one thell me what any 4 outrunner motor is = to this outrunner motor??????
 Mike K 126 points
Take a look at the Hacker A60-14L 192kv
Customer Reviews
Overall Rating
Like it?
Ordered one 2 weeks ago (paid a fortune for delivery in 7 days), Speedpost lost the parcel and HobbyKing says that the investigation could take two (2) months and until then I could not get any indemnisation!!! I have also bought other things, total $390. Worst service ever, it's a pitty!

2 comments. Reply..

Overall Rating
Like it?
Finally tested the motor with the Turnigy dlux 160HV ESC. So far I have done measurements without any load to the motor. The motor seems to work OK so far (I hope it will continue to do so!). I use 12S LiPo to power it. The motor draws 4.5-5.0A of current at 45-49V of voltage at room temperature without any cooling. I will repeat the measurements for longer times (those values are for 10-20s running time). For quality I put 3 crowns for the reason mentioned in the discussion about the fixation of the stator which seems to be bit doubtful.

3 comments. Reply..

Overall Rating
Guy Hanoch
Like it?
I love this motor!!! ordered 2 of them , one for electric scooter and the other for electric skateboard. on 6S setup with 10 km range it work great and not overheating it's copy of the great Hacker A60 and really good one!

5 comments. Reply..

Overall Rating
Like it?
Good motor. I made 20 to 30 flights on 12s and there are absolutely no issues. Havent measured any watts yet, but it gets pretty warm with a 18x12inch prop. Seems not to be a problem...

No comments. Reply..

Overall Rating
Like it?
Great motor
Using it on an electric scooter with 8s 16A/h battery pack. Have put down 150miles on the motor. So far no issues. Great buy.

7 comments. Reply.. here to see all reviews
Aff. Link