Turnigy TrackStar 1/10th Scale 60A Car ESC Version 2 (AUS Warehouse)

Total of 5 discussions.

Brett

1 points - 2/12/2013

Can any one tell me which is better the version one or two in this 60 amp esc.Version one will take a 4s is that correct ?

smiley

19 points - 8/21/2012

I have the version 1 and program card. Does this new version 2 use the same programming card?

smiley

19 points

It has different software to the version 1 esc. Needs a different program card, but works much better. Goes hard in a slash running the Traxxas velenion motor

Biss74

1 points - 8/9/2012

Could you use this in the 1/16 SCT

seehuusen

21 points

it's a bit overkill, but it would work :)

Biss74

1 points

Thanks my son keeps frying 25A esc

troy

4 points - 3/31/2012

hi guys. i have this esc and a 13.5turn motor. it starts up very rough (stuttering) until it gets a bit of speed then goes good. my motor runs perfect with a 25amp esc. is this esc no good for a 13.5turn motor? thanks

Michael

3 points

Which 13.5t motor are you using. A 60amp speed control should have no problems with a standard 13.5T 540 size brushless motor unless the programing is incorrect. You may need the Turnigy Trackstar 60A ESC Programing card to set the ESC up with the appropriate settings. If you have changed the gearing however to a very tall gear setup, you may need to gear it back to an appropriate level. Please provide further information.

troy

4 points

The motor is a bullistorm thing I got off eBay. The gearing is standard. I think I may need the program caRd because my hk25amp esc runs it no worries.

Michael

3 points

Hi Troy, I would be pretty confident in saying that its a programing issue and that you will need the programing card to rectifying the problem.

mrmat01

2 points - 1/10/2012

Hi guys what is the best program card to use for this speedy mort important voltage cut off wont to be able to set at 3.5v ser cell.
Thanks in advance

Daniel

2 points

Hello . How many turns is possible for an Motor . Or have you some recommendation.

mrmat01

2 points

Hi im running a 10 turn but would be good from 9t to 13t

Customer Reviews

Overall Rating		BUGgYNuT 3 likes
Value
Quality

Like it?

Went hard while it was going but the tiniest bit of water caused it to fry itself and a Ni-Mh battery pack i had hooked up to it in my brush-less buggy

6 comments. Reply..

Overall Rating		ryeboy10 3 likes
Value
Quality

Like it?

recived one for my slash fitted it lasted one minute,then smoke poured out and now dosent work...iv orded another one hope it lasts MUCH longer other wise i will go for a bigger brand name.....i will repost when i recive next one...

1 comment. Reply..

Overall Rating		david 1 likes
Value
Quality

Like it?

Great value for money use it in my xray t2 with a ezy 9t with a turnigy lipo and i easily keep up with the big brands curently running 3 with this setup h

No comments. Reply..

Overall Rating		smiley 17 likes
Value
Quality

Like it?

I bought 3 of these, one was faulty from new; no low/middle power and no reverse (still useful as BEC when setting up electronics). The other 2 went well, although the reverse delay is quirky. One experienced moisture from a muddy track and died. The third is still doing strong in my Traxxas Bandit. It has since been filled with epoxy to make it waterproof. I'll repost when/if it dies.

No comments. Reply..

Overall Rating		Redfrog 1 likes
Value
Quality

Like it?

My particular combination with Speed passion RTR motor cogged badly then the magnets dislodged from the motor. Bought two of these units but have since sold them.

2 comments. Reply..

.....click here to see all reviews