Please confirm your location:


Arkansas warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the Arkansas warehouse even better value!
  Item found in the following categories;
> Hardware & Accessories > Spinner/Adapters > Adapters

  RATED:

Propeller Adapter (Collet Type) 3mm

Propeller Adapter (Collet Type) 3mm

Propeller Adapter (Collet Type) 3MM

Spec:
Motor Shaft: 3mm
Prop Shaft: 6mm
Prop Shaft length: 24mm
Weight: 13.2 grams



PRODUCT ID: GON-D3T6

Shipped from:
International Warehouse

Price

$1.24

Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
5128
crowns
  
 
Total of 65 discussions.
TRAMOYON  1 points - 6/29/2016
 
Hi Chri5k4t, I think I have found the problem - if I just firmly push the collet onto the motor shaft without collar, washer or nut/spinner and slowly rotate the motor can with the now extended threaded shaft, the "out - of - round" rotation of this "new" threaded shaft is quite obvious. No matter what I try, I cannot eliminate this obvious "out - of - Round" rotation. I have ordered another two to test (why not at this price ?). Thank you for your interest and assistance.
TRAMOYON  1 points - 6/28/2016
 
Hi Chri5k4t - Don't want to draw this discussion out too much, but did you cut off (shorten) your motor shaft? I think my vibration may be due to cantilever effect of long motor shaft ?
 Chri5k4t 52 points
Hi. No I didnt, but it is a very long shaft and the further it is from the can of the motor, any vibration will be exaggerated. If you bolt the spinner onto the motor without a prop and slowly run it up, do you get a large amount of vibration. I might have just been lucky with the ones I have, but the spinner section of the collet should all be turned on a threaded mandrel. It will take some pretty poor machining to **** it up that badly.
TRAMOYON  1 points - 6/16/2016
 
I flew this morning and it flies beautifully with the nut locking the collet onto the shaft - I don't think the spinner is sufficiently well balanced to try on my very light "Clouds Fly". I changed from the rubber "O" ring prop - saver because I didn't trust the rubber "O" rings - they have a tendency to fail.
 Chri5k4t 52 points
I have one on my AXN, it work fine.
BEST ANSWER CREDIT AWARDED
TRAMOYON  1 points - 6/14/2016
 
My motor shaft diameter is 3.0mm, but it is about 15mm long - which may contribute to the problem ? If I use the spinner to lock the collet onto the shaft, I get too much vibration. If I use the small nut (supplied) to lock the collet and propellor onto the shaft it seems OK, but I haven't flown it yet !
 Chri5k4t 52 points
Have you balanced your prop and does the problem happen when just the collet is on?
TRAMOYON  1 points - 6/13/2016
 
My spinner also caused a lot of vibration. Not worth returning. Seems to work OK using the supplied nut to lock the collet onto the shaft - haven't flown it yet though.
 Chri5k4t 52 points
Just want to say that mine was perfect. I clocked it and the accuracy was certainly acceptable, what size motor shaft did you put it onto, if the shaft is too big for the original machined hole it will not fit and will twist.
Customer Reviews
Create an account
Overall Rating
*Mac2*
32 likes
ValueUNRATED
QualityUNRATED
2 thumbs up!
Perfetto , ha una filettatura abbastanza lunga che permette di inserire qualunque elica.


No comments. Reply..

Create an account
Overall Rating
Herbyaespen
325 likes
Value
Quality
1 thumbs up!
Top Spinner für alle 3mm-Wellen. Damit kann ich bei meiner Dynam-Catalina, der Cessna 350 Corvalis von ST-Model und der Canadair von GuanLi die wenig präzise Prop Befestigung auswechseln. Gewinde mit der Flex abschneiden, Prop-Adapter drauf und schon passt's


No comments. Reply..

Create an account
Overall Rating
Olegator
17 likes
Value
Quality
Like it?
Good card, well compressed, balanced. 5 stars.


2 comments. Reply..

Create an account
Overall Rating

277 likes
Value
Quality
Like it?
Gewicht ca 13g mit Scheibe, der Spinner davon ueber 6g!
Die Scheibe ist noetig bei sehr dünnen LS oder bei Mutternbefestigung (da kann amn sich den schweren Spinner sparen!)
Gesamtlaenge 35,5mm
Lufschraubenaufnahme 23,5mm
Spinner 24mm 17,7mmD
Anziehbohrung 3mmD


No comments. Reply..

Create an account
Overall Rating
v8surf
4 likes
Value
Quality
Like it?
Good centering, and not too heavy. Will buy more indeed if I need them


No comments. Reply..

.....click here to see all reviews
Aff. Link