USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
A fun and easy to fly paraglider. The motorized paraglider hovers like a helicopter in a gentle breeze and can perform basic stunts.
The kit assembles is 10 minutes and includes a simple radio. Don't expect fantastic performance from this model, rather, hours of stress free hovering and floating around your local park or hillside.
Hola, no esperaba gran cosa de este modelo. Pero no he conseguido conectar la emisora con el receptor de ninguna forma. Imagino que el mó*dulo receptor/variador está* roto, pues se queda parpadeando continuamente. Si lo llego a saber, compro un variador por si me pasaba esto, y usaba el receptor de mi emisora.
Saludos.
hola diego ..eres españ*or no????una pregunta sobre la aduna este articulo me gusta pero tengo miedo k melo paren an la aduana ..tu as tenido algun probrema con eso???? unn saludo
Hola Salvador, pues segun el valor del paquete te lo paran o no (al menos eso tengo entendido). Me lo pararon, pero los de correos se encargan de todo y te cobran el IVA y los gastos de aduana, te llega a casa sin problemas.
Suerte.
Hi Matthew, have you tried resoldering your bullet connectors? The other possibility is that you're overloading your speed controller, sometimes the mounting screws are too tight warping the rear motor mounting caseing causing the rear bearring to bind, the motor should turn freely.
Where can i get a brushless motor for this? I have one from years ago and i set it up to use a hyperion 2850 kv motor geared and worked great, but now it glitches like crazy and everything has been replaced but a motor and I CANNOT find a motor (inrunner or outrunner) to fit in the limited space! Does no one make a ~3000 kv 24mm dia, 2mm shaft with a weight of 50 grams, capable of 10 amps anymore??
Otherwise, why does this thing glitch so much? I cant imagine why the motor went bad or if it is, but what else could it be?
Prop has no markings but it is very close to a 9070 Reverse Pitch SlowFly prop which makes sense as it has a brushed gear drive system. Check out the multirotor section for the reverse pitch propellers.
I have bought the HK 30A brushed ESC, can I straight soldering the motor to the brushed ESC and connect to my my RX? If I use my own RX I only connect the servo to elev then I can control left n right.
The unit has a all in one RX-ESC unit with a proprietary 2.5 Ghz radio system. Using your own Radio Tx/RX/ESC will work but why stop there, why not convert to full brushless which will last longer and provide more power and flight time.
yes, because there says ARF but the descritipons says:
Required:
8 x AA batteries (for the Transmitter)
800~1000mah 7.4v 2S Lipoly
like all is included what do you think
Orlando, creo que va a quemar los 3s CES, además de que no caben dentro del compartimiento de la batería, como cambiar la esc, la radio y el motor, esta posibilidad existe, sólo tienen que observar el diámetro y la longitud del motor de modo que es posible usando la misma caja de cambios que está instalado en el parapente, y preferiblemente un brushlless motor. He buscado en Google para el futuro de caja de cambios en caso de rotura de la vela a llegar, y esto:
http://www.hobbyking.com/hobbyking/store/__15 244__Gear_Box_3mm_22T_64T.html
Tomando nota de que la cinta tendrá que ser una adaptación.
Cleyton
Cleyton: Muchas Gracias por tu respuesta. La radio me da 200 metros de alcance, lo comprobé* alejando el Transmisor y funciona perfecto, hasta esa distancia.
Alguien sabe si puedo utilizar una bateria Lipo de 11,1 voltios (3S) con este mismo motor y receptor? o quemarí*a todo? ¿*Y una baterí*a NiMh de 9,6 voltios? Desde ya muchas gracias en lo que puedan ayudarme.
Caso contrario deberé* cambiar motor, ESC y radio. El tema es que voy a tener que desarmar todo. Orlando
Orlando, el problema debe ser el alcance de la radio, que es muy pequeño, me recomiendan cambiar la radio y esc para poner fin a este problema. Siga las sugerencias:
http://www.hobbyking.com/hobbyking/sto re/__6468__Turnigy_30A_BRUSHED_ESC.html?strSearch=br ushed
http://www.hobbyking.com/hobbyking/store/__83 38__Hobby_King_2_4Ghz_4Ch_Tx_Rx_V2_Mode_2_.html
Cle yton
Compré* el producto desde Argentina y lo recibí* en perfectas condiciones, todo funciona ok. Vuela perfecto, responde excelentemente a los mandos. Solo que pareciera que le falta potencia, no puedo hacer que se eleve mas de 8 o 9 metros. Le doy potencia al má*ximo pero queda siempre a la misma altura. ¿*Como puedo solucionar esto?. Gracias.
You put a esc for brushed motors, but you also have to put the receiver rx, because the original receptor already have the built-esc. It may be a esc 30A. Have here in the hobbyking store. The ideal is to put brushless kit complete with 2s battery
get a reciever from a complete radio system (not the stock one), this new radio must have "elevons" or delta wing programming capabilities just plug one servo to aileron, the another to elevator (with the mix already programmed in radio) and esc to the throttle channel, of course the other leads from esc go to motor, set it up as for movement (in case you need to reverse) and you are done.
sidd ... why use elevon or delta mixing? This only uses the yaw servo to turn and throttle to go up and down. What other servo would you connect on the other channel to and why mix rudder to aileron or aileron to elevator for that matter? Three channels will be perfect and two channels will work.
Olá* Cleyton, Infelizmente a Hobbyking nã*o vende peç*as separadas deste modelo. Neste caso eu partiria para a adaptaç*ã*o de um motor brushless, assim como uma gearbox, mas para isso teria que pesquisar e ver o que existe no mercado que pode ser adaptá*vel.
do you have the p-glider-arf in the usa the shipping from china is verry expensive im ready to buy this unless i can get a shipping discount they quoted around $30 if i can pay around $15 i can purchase this
for this case since the motor seems to be brushed a 3s would burn esc and motor, so stay with 2s. If it was brushless it would fly with 3s with proper throttle management.
I bought two and one of them did not work. The radio controls do not respond, neither the acceleration nor the direction command. Anyone have any solution?
Daniel,
Bom dia, o recptor que vem neste sistema serviria????
http://www.hobbyking.com/hobbyking/sto re/__8338__Hobby_King_2_4Ghz_4Ch_Tx_Rx_V2_Mode_2_.ht ml
Olá* Rafael, Infelzmente o Range do radio é* muito pequeno... somente 15 metros.... Se vc possui outro rá*dio , sugiro que compre um receptor parkfly mais potente e troque o sistema de RX/TX.
Se vc nã*o possui outro sistema de RX/TX, vc pode verificar aqui no site mesmo... existem opç*õ*es excelentes da linha ORANGE que vã*o certamente resolver seu problema.
eu comprei um deste mas nã*o funcion.
algué*m pode me responder porque ele começ*a a voar e sinal do controle acaba metros depois? as pilhas estã*o ok. obrigado.
Got this para-glider to take off from the ground. Surprisingly tough given the rough landings. The wheels pop out but are easy to put back on for the next flight.
2 comments. Reply..
Overall Rating
mike99ca
15 likes
Value
Quality
Like it?
Just got it yesterday. Over all it looks nice but it feels all too fragile. Maybe it will fly ok and I'll not break it on first landing. One complaint I have is that kit is missing servo horn. Can't fly it before I figure out what to install instead. Other then that good value for money I guess.
Yes! Beside heli and plane, you will need this one during the summer~ Easy to fly and easy to control. To order one for you and your kid right now~
No comments. Reply..
Overall Rating
WazzaG
18 likes
Value
Quality
Like it?
Endless fun, with 1000mah battery I get 13-15 minutes of flying. This paraglider can take a beating! I have managed to do a loop one time, I have tangled it up at twice the height of the football stadium light posts and slammed it into the ground with only a broken prop, hit barbed wire, poles, fences, people (me! Stitches in my hand :( ). One thing you need to know is the prop will push into the motor housing and the gear drive will be chewed out if not careful a simple homemade spacer will suffice I can upload images if anyone needs. Best fun i've had. Also this can carry heaps of weight e.g. camera, soon I will try FPV.
PS I have bought 3 (2 for spares encase they stop manufacture)
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg)
.jpg&width=48)
.jpg&width=48)
.jpg&width=48)
.jpg&width=48)
