Please confirm your location:


Arkansas warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the Arkansas warehouse even better value!
  Item found in the following categories;
> Electric Motors > TURNIGY
> Electric Motors > TURNIGY EasyMatch
> Electric Motors > Outrunners by size > 45 to 50mm

  RATED:

Turnigy G46 Brushless Outrunner 670kv (.46 Glow)

Turnigy G46 Brushless Outrunner 670kv (.46 Glow)
Turnigy G46 Brushless Outrunner 670kv (.46 Glow)

Designed to be a direct swap out for your .40 to .46 size glow engine. This brushless outrunner will provide more power and with it's high efficiency, long run times.
A quality motor, built specifically for planes designed to fly with a .40 ~ .46 glow engine.
Spec.
Battery: 4~5 Cell /14.4~18.5V
RPM: 670kv
Max current: 40A
No load current: 10V/3.9A
Current capacity: 55A/15sec
Internal resistance: 0.04 ohm
Weight: 303g  (not including connectors)
Diameter of shaft: 6mm
Dimensions: 76x50mm

Required; 
60A ESC
4S~5S Li-Po / 12 ~ 16-cell Ni-MH/Ni-Cd
12x8 ~ 14x10 prop
Suitable for sport and scale airplanes weighing 4 to 7 pounds (1.8–3.2 kg).


PRODUCT ID: G46-670

Kv(rpm/v) 670
Weight (g) 303
Max Current(A) 40
Resistance(mh) 0
Max Voltage(V) 19
Power(W) 741
Shaft A (mm) 6
Length B (mm) 55
Diameter C (mm) 50
Can Length (mm) 24
Total Length E (mm) 76
Update/Add my own data
Customer Data

Shipped from:
International Warehouse

Price

$52.31

acc.
  • Turnigy EasyMatch G46 Series - Replacement Shaft

    Combo Price: $2.10   IN STOCK
    Add to Cart

  • Turnigy G46 & G60 Series Accessories Pack

    Combo Price: $3.99   IN STOCK
    Add to Cart



Further discounts available for registered & logged-in customers.
 Customer rated
557
crowns
  
 
Total of 98 discussions.
ATAN #1  90 points - 2/7/2016
 
What if put this on a foam P47 Thunderbolt 1600mm w/span, 3.3kg~4kg auw, 4s 4000mah 30c, 17x8 or 17x10 prop, Turnigy Plush 60A, additional external BEC.. What will happen? What is the estimated amphere load, thrust achived,and watt at max?
 bigtiii 69 points
You want to use the 80-120W per pound rule for scale/sport flying and go from there. So with a 14.8 volt battery to achieve 120Watts max you'd be pulling just over 8 amps.
Peter  29 points - 2/2/2016
 
Is .04 ohm internal resistance a lie or is that actually right?
 Hobbyking Ian 62 points
According to my notes its correct.
 Peter 29 points
Thanks Ian
F-HG-  1 points - 1/30/2016
 
This motor has 14 poles - if somebody likes to know.
Adam  1 points - 1/3/2016
 
Can anyone comment on the thread size for the collet adapter. I want to add a closed/rounded hex nut to the end of the shaft. I am guessing it is either M8x1.0 or M8x1.25, but that is just based on other collet adapters for 6mm shaft in the store. Thanks in advance for any help.
Robert  1 points - 12/1/2015
 
Can someone tell me if this motor is drilled and tapped to accept a bolt on prop adapter instead of the billet connector?
 Robert 1 points
Sorry, I meant the collet prop adapter.
 CHRISTOPHE 1 points
No only the collet prop adapter is suitable. Be careful the Motor Shaft is 6mm, and the Prop Shaft is 10mm. You have to drill your prop. You may also find a 6mm prop adaptor, with a prop shaft of 8mm. A lot easier to adapt your prop, specially wuth a Tapered reamer for propellers wich goes from 5 to 9mm.
Customer Reviews
Overall Rating
pulsery2k1
64 likes
ValueUNRATED
QualityUNRATED
1 thumbs up!
I just recived this and it's well made seem's much better then
there sr line has an excllent feel to it ,bearing's feel good

I tested it with a master 13X 6 prop

on 4S it gave 28 amps 410watt's
on 5s it gave 40 amps 830 watts

plese note the above numbers is the avarage of running the motor
60 second's at full throttle .
it does seem to like 5 S motor was only slightly warm after each
run


12 comments. Reply..

Overall Rating
Carlos JR
34 likes
ValueUNRATED
QualityUNRATED
Like it?
Alone queria to ask if this motor is better than the TR50-55B, the specifications technos are seemed among both although the TR50-55B has the axis of 8mm, They weigh practicamente the same thing although the G46 is but long. The TR seems to deliver but power that the G46 being the first one of smaller price, some 10$ 7.
I am very interested in acquiring a motor of these, but before he wanted that personal qualified of HK he removed me of r


6 comments. Reply..

Overall Rating
Carlos JR
34 likes
ValueUNRATED
QualityUNRATED
Like it?
I am very interested in acquiring a motor of these, but before he wanted that personal qualified of HK he removed me of referring doubts to these two good motors. My question is the following one: the G46 is better than the TR5055B?, and if is affirmative, because motive?. The questions in cuestion I carry out them for the difference of price among both motors.
It is possible that the G46 this manufactured with better materials, himanes, t


5 comments. Reply..

Overall Rating
Carlos JR
34 likes
ValueUNRATED
QualityUNRATED
Like it?
It is possible that the G46 this manufactured with better materials, himanes, thread, Steel etc? Agradeceria a lot that answered to these questions since in this way ayudarian to all the buyers to take better and but rapidamente their decisions of purchase.
Excuse for the English, I am utilizing a translator.
A cordial greeting and thanks.


2 comments. Reply..

Create an account
Overall Rating
grets
60 likes
ValueUNRATED
QualityUNRATED
Like it?
Its now November probably wont be using this motor until next Spring. I hav at least 10 other Turnigy mototrs of various sizes and havent been disappointed yet!


4 comments. Reply..

.....click here to see all reviews
Aff. Link