Please confirm your location:

USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Radios & Receivers > Complete systems
> Radios & Receivers > JR
> Radios & Receivers > FrSky > Modules


FrSky DJT 2.4Ghz Combo Pack for JR w/ Telemetry Module & V8FR-II RX

FrSky DJT 2.4Ghz Combo Pack for JR w/ Telemetry Module & V8FR-II RX
FrSky DJT 2.4Ghz Combo Pack for JR w/ Telemetry Module & V8FR-II RX

FrSKY ACCST technology is proven, approved by many model associations, tested and reviewed as the leading Chinese 2.4Ghz R/C Technology. If you think DSM2 or FASST is the best, think again!
New FrSKY ACCST (Advanced Continuous Channel Shifting Technology) gives you secure radio communicatios in 2.4Ghz band. ACCST 2.4GHz system shifts 80 channels around hundred times per second in the 2.4GHz band. This means that the system is completely resistant to interference in that band. 
Advanced Continuous Channel Shifting Technology (ACCSTis our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility.
Easy to bind and very fast link-up. 
Excellent reboot time. 
True Diversity with two antennas.
All channels can be programmed with Failsafe, quickly and easily.
Quick and extremely stable in performance.
Precise and smooth servo response.
Extended range (1.5km-2.5km).
FrSky DJT is compatible with JR transmitters following:
JR: 347, 388, 783, U8, PCM10, PCM10S, PCM10SX, PCM10IIS, 8103, J9303, PX, 9XII, 11XZERO
Receiver Specification:
Operating voltage: 3.0~16V(HV Version)
Power consumption: 30mA
Resolution: 3072
Latency: 22ms
Number of channels: 8
Range: 1.5km-2.5km
Dimensions: 44 x 24 x 14 mm
Weight: 9.3g
Module specification:
Operating voltage: 6.0V-13.0V (can handle 3S!)
Power consumption: 50mA
Output Power:: 60mW
Resolution: 3072 (11bit)
Dimensions: 63.9x48.5x36.5mm

1 x 8-channel Telemetry Transmitter Module DJT
1 x Transmitter Antenna
1 x 8-channel receiver V8FR-II (HV Version)

* Transmitter Module is compaitble with all V8 NON-telemetry Recievers


Weight: 147g
International Warehouse
Price  $39.99

  • 2.4Ghz 7DB Antenna for FrSky Modules (And compatible Radios/Modules)

    Combo Price: $5.51   IN STOCK

Further discounts available for registered & logged-in customers.
 Customer rated
Total of 758 discussions.
Sam  1 points - 2/24/2015
If I get these Taranis, do I need any other product's to read the voltage data on the Taranis?
 Sam 1 points
Everything didn't seem to come through. I meant if I get these modules combined with a Taranis, if there is any other product's needed to read voltage data from the multicopter on the Taranis.
 v_max 4553 points
This module is NONTELEMETRY one.. It do not able to send any data back from RX to TX. You need to choose other combo (Product id: DJT) or use D series receiver (any one frsky rx with D in first letter of model ) with TX module from this combo. All frsky telemetry receivers (D series) has analog input for battery voltage sensor.RX has analog input for voltage signal input ... All you need is resistive divider to scale full lipo voltage to this input range.
 Justin 78 points
You will need the additional sensors along with the sensor hub to use the full telemetry. If you get a telemetry Rx with this module you can have the battery voltage displayed by connecting the Rx to the fc as long as its compatible. Just remeber this Rx is non telemetry only the module itself is telemetry capable. I got this combo for my 250fpv and put the d4r-ii rx into my bigger quads with GPS so I can use the telemetry.
 Matt 1 points
As stated above you would need the Telemetry RX. If you wanted a cheaper alternative way to monitor voltage I would recommend a Voltage alarm. They are under 5$ and are indispensable
 v_max 4553 points
Matt, it's not alternative... what's the sense in beep-beep when it's 1km away from you * )
Tomas  1 points - 2/24/2015
Do not fit in my Turnigy 9X. I had to cut some plastic from transmiter
 v_max 4553 points
There is a simplier way I use... cut out plastic separators around sockets on this MODULE
Can  1 points - 2/23/2015
Can I use this with flysky 9x
 fjmb58 510 points
I assume you mean Turnigy 9X, Flysky is a different manufacturer to Frsky and uses different modulation/ encoding systems. But yes this module will work with a 9x with a small mod(check Vmax's post below) or will fit straight in to a 9XR or 9XRPro, a better choice than the 9X.
 v_max 4553 points
Assuming you are asking about Flysky TH-9XB... Sure you can. But you need to change both : tx module and rx. as it's not crosscompatible with stock RF module/receiver as . fjmb58 mentioned above.

fjmb58 , Flysky TH-9XB is absolutely the same turnigy 9x..
stoc005  15 points - 2/20/2015
I installed this module into a JR 783 and was able to bind it to the receiver. But, all the controls were at the ends of there travel. The sticks were unable to return the servos to neutral. Installed the module into an X9R w/ OpenTX. Worked perfectly without having to rebind. How come it won't work in the JR Tx? The X9R works flawlessly.
 v_max 4553 points
this more likely means problems with PPM signal input to module. As I can see from fotos of JR 783 it has selectable modulation type PPM/ZPCM/SPCM More likely it currently in one of CPM modes and you just need to change setting to PPM
 stoc005 15 points
Duh! That's it. I forgot I was using PCM. PPM will work fine.
polykarpos  5 points - 2/16/2015
hi if i put this module do i have to change the software of the 9x?
 fjmb58 510 points
In short No.
 v_max 4553 points
fjmb58, right. I'd like to add that on 9x you would need to do 2 mods... First unsolder antenna from inside stock module, then untighten antenna fixing screw and pull out stock antenna with wire... Second.. due to some extra plastic around module pins on tx body frsky do not fut module dock completely. So you need to remove this plastic around connector pins ... This requires disassemble t9x to take off backplate pcb to get free and safe acsess to cut this plastic. The alternative simplier solution I use - cut out plastic separators between frsky module connector socket. Mach earier to do.
Customer Reviews
Review Blogs for this item
need help with fr sky mod
Frsky blink
Overall Rating
3 thumbs up!
The JR 3810 is the same radio as the 8103. For marketing reasons it is labelled as the 8103 when sold in the USA, and as the 3810 everywhere else. Modules are interchangeable. The numbers stand for 3 model types, 8 channels, 10 model memories. So yes, it will accept the FrSky module.

2 comments. Reply..

Overall Rating
3 thumbs up!
Guys, I been using this modules since their first beta system , and I can tell you is the BEST SYSTEM YOU CAN GET here is the main Thing I can say:
a) True FHSS system (equivalent to Futaba FAST Frequency hopping)
b) True Fail Safe setup (and easy to setup)
c) Range test perform in our clud give better than 1.2 miles and this under heavy noise (we had 5 Spektrum and 5 Futaba systems ON plus one wireless system plus a noise generator on the 2.

11 comments. Reply..

Overall Rating
3 thumbs up!
c) Range test perform in our clud give better than 1.2 miles and this under heavy noise (we had 5 Spektrum and 5 Futaba systems ON plus one wireless system plus a noise generator on the 2.4GHZ spectrum) and the system perform w/o a problem.
d) Very tolerant to low voltage (put down the voltage under 3V and still was working)
In few works VERY GOOD SYSTEM, much better than any DSM system (Like Spektrum DSM2 or Corona DSM etc.), Ve

No comments. Reply..

Overall Rating
Hong Soon
2 thumbs up!
Very attractive module with proven track records. I have yet to try this out on JR 3810 transmitter. I would do it and keep you guys posted.

6 comments. Reply..

Overall Rating
2 thumbs up!
I have this in a Flysky 9x(same as turnigy 9x on here) ans it's excellent.

49 comments. Reply.. here to see all reviews
Aff. Link