HobbyKing AP-02 7000kv Brushless Micro Motor (2.3g)

Total of 6 discussions.

jetson3000

28 points - 1/22/2013

Is it good for Walkera CB100 tail BL motor?

Fadii

1 points - 12/18/2012

Hi Guys, I am using a micro receiver with built-in ESC. The motor connection point on the receiver has only two holes. Would it be possible to use this motor on my receiver, or have I just bought the wrong motor? If it's possible, how do I know which two wires to connect to the receiver, and what do I do with the third wire that's coming out of this motor? Many Thanks!

one-flight

55 points

Hi Fadi - wrong motor. Your receiver suits only brushed motors ( e.g.Micro Power system w/ Gearbox GPS-7. Depends one size /weight of your model)If you want to use this brushless Motor you need an TGY DP 3A 1S 1g Brushless Speed Controller and a spare channel to connect this esc.

BEST ANSWER CREDIT AWARDED

Fadii

1 points

Thank you one-flight, I know i could really use the ESC you mentioned in the future. It's pretty light! For now, I shall try to refine my model more. So far, I've just finished building a 18g AUW model, powered by a brushed 7mm direct drive motor, and I managed get it to cruise at 75% throttle. I'll try the GPS-7, it could give me more liberty. Cheers..

adammooren

616 points - 5/12/2012

does anyone have the static test data for a 5x3 or 4x3 prop?

Wolfgang

1 points - 3/22/2011

I have two questions to the motor:

1. How to fix the propeller to the shaft?
2. Is the BR3A speed controller right to operate the motor?

Thanks

SouvenirOrigami

2 points

I use AP-02 from HK for my cb100.. for fix the propeller or tail blade you can tied/binding blade using sewing thread...

Thanh

10 points - 11/17/2010

Anyone has photo of the back of this motor? Thanks

Alexander Alexeevich

3 points

You can see the back side of the motor with prop www.link

JamesBandid

6 points

I will take the photo today, may send out this afternoon.

Camboui

134 points

Look for the AP03 4000KV or, better, the NTM 13-12 2400KV. You'll see how the back looks like. (credit please)

SteveM

13 points - 11/22/2009

please advise if this motor is ballraced...rgds

magnusEl

1215 points

Yes, there is ballbearings in it.

Customer Reviews

Overall Rating		Tapio L 35 likes
Value	UNRATED
Quality	UNRATED

3 thumbs up!

A nice motor. I had bought the 2g hexTronic motor before, but never got that really run nicely. Might have been a problem with the ESC, but then again, read in the net about bearing problems of that one, too. This AP-02, OTOH, works smoothly with the HK mini-ESC. The 1.5mm shaft could be fitted with a prop adapter, but the 3020 prop can also be slightly reamed to snugly fit the shaft. Just need to build a model for the power train... :-)

1 comment. Reply..

Overall Rating		Ar 22 likes
Value	UNRATED
Quality	UNRATED

1 thumbs up!

Excellent upgrade for 4G3 micro heli- tail motor. More power than original brushless motor, fits motor holder with only 1 small adjustment (cutting away 1 bar for motor axle).

No comments. Reply..

Create an account

Overall Rating		haddad 84 likes
Value	UNRATED
Quality	UNRATED

Like it?

Amazing motor for 1S lipos. I got 36g thrust with a GWS3030.

No comments. Reply..

Overall Rating		Fliegerbieger 8 likes
Value	UNRATED
Quality	UNRATED

Like it?

I use this motor in a small depron-glider. 1g ESC, 2xToki servos, 5ch pene reciever, 1S 138mAh Lipo and GWS 3x2 porpeller. Flightwight 37.5g (wingspann84cm). Its a little bit noisy but it's ok. The power of the motor is super!

1 comment. Reply..

Create an account

Overall Rating		donaldsnephew 134 likes
Value
Quality

Like it?

Use it as micro heli tail motor. Different kind of mountings (screws beside axis) would be good.
Good motor, not that cheap, but very good.

No comments. Reply..

.....click here to see all reviews