Turnigy 5000mAh 3S 25C Lipo Pack

 rahulvyas 311 points

yup:)thx

 Roger 2245 points

You need a 4mm Bullet-connector for the accucel6, or you can use the alligator clips to XT60 connector that comes with the charger.

 KaSoAn 1 points

Roger, thanks for your contribution. I was more thinking like a picture of the battery hooked up to the charger. Which wires go where. And then a step-by-step guide for this battery and the Accucel-6 together. Like,1: do this, 2: do that, 3: do this, 4: watch out for this...

 Roger 2245 points

Hi Kasoan, do you already have these items or you just want to know how to connect it? Cause when you have the items already, I think you will be able to figure out how to wire it yourself. Will take a picture of the 4mm bullet connector later to show you how.

 KaSoAn 1 points

I have already received the items. I can see that the bullet connectors go into the discarge plugs on the charger (I have already soldered a new cable) and that the JST-XH plug fits into the charger. My question (among many) is, should I connect both cables at the same time? Which charger settings are suited for this battery pack? In which order do start the process? What about all the warnings I read in forums, will the whole thing blow up and how to prevent it?

 Roger 2245 points

You should plug both the JST-XH and the bullet connector. Even when doing just the regular charge, balance charge or the fast charge. This way, you will be able to monitor the individual charge of the cells. This battery pack can be charged up to 2c (10A) but I charge mine with just 1C (5A) since that's the capacity of my charger. Don't worry too much about the warnings about exploding lipo, it is true but I don't think you will be able to over-charge this lipo with the accucel 6, it has auto cut off safety features so your safe, you can choose, current limit or time limit. It also stops charging when the lipo is full. As a newbie I was alarmed by those warnings too, but if you see the videos in you tube, deliberate overcharging of lipos to let it explode involves a few amps more than the limit of the lipo. Read more from forums and learn some safety precautions and your gonna be fine. :)

 Christopher 49 points

about 10 mins

 Christopher 49 points

Yes depending on the plane and the power draw. Give some details on what you are using.

 Gary 2974 points

2C is perfectly ok,personally when I am out flying and want to recharge my battery I will charge at 2C,when I am at home and time is not so much of an issue I will charge at 1C or less.

 Roger 2245 points

Yes it will, a bit loose but adding some protective foam or something will make sure it won't move around during flight.

 Lanius 110 points

You've over-discharged your battery. Charge it in Nimh program first. You must charge the battery in Nimh mode until it reaches 9.6 V. You must be present during the operation because it may overheat. When you get to 9.6 V using 3S LiPo balancing mode. On the next flight be careful, surely you've lost some battery discharge capacity. I recommend using a voltage warning buzzer (P. Id: DL-Volt-Alarm)

 Almm# 1 points

comprei um bateria igual demorou 1 mes pra chegar

 ANDRE_SAMPA 7 points

olá* amigo aqui é* para descutir sobre o produto, voce nao vai ter nenhuma informaç*ao sobre seu pedido neste campo.

 Lanius 110 points

El tiempo de entrega es variable. Pero normalmente entre 12 dí*as y 1 mes es lo normal.

 Akshat 55 points

When you set Your Charger To 3s,it will automatically charge the pack at the rated voltage but when it comes to the current..you have to specify that in accordance with your pack..as in this case any value bellow or equal to 5 amps should charge your lipo safely..good luck

 cavok 1 points

Thanks a bunch Akshat!

 Germano 42 points

Oi amigo. Infelizmente não cabe, a não ser q faça algum tipo de alteração no compartimento de bateria pois a dimensão máxima para baterias é 140mm x 47mm x 33mm. E a bateria em questão tem 146 x 50 x 25mm.[]

 Dinukap4 253 points

Yes i too bought it for my Rustler and it fits perfectly..

 Joao Paulo Francis 1 points

Exelente bateria, uso no meu traxxas Slash e roda 100pcnt Alto torque alta duração com bons carregadores. recomendo a todos a HobbyKing Excellent battery, use it on my traxxas Slash and runs 100pcnt High torque high boots with good length. I recommend everyone to HobbyKing

 山田 1 points

jcbcado???????????????????????????????

 justforfun 84 points

yes, but obvioulsy you will need two.

 Peder 1 points

I know i need two batteries *)
Since they wil fit i the savage. I ask about it is a good batterY?

 FluxNZ 6 points

Height and length is fine but the 25mm width stops the lid from closing due to the little bit extra width. These will fit: www.link are a little bit thinner which makes the difference. To be fair I haven't noticed any difference between the non nano and these ones performance wise.

 hawn1 10 points

yes it will fix the savage flux along with the 1/10 traxxas trucks

 Peder 1 points

So wil it fit or not?
Rhys your link did'nt work.

 FluxNZ 6 points

Sorry Peder didn't know Hobby King masked links in the replies. The linked was for the Turnigy nano-tech 4500mah 3S 25~50C Lipo Pack, it's 22mm wide and fits the standard Flux box fine (use the size of this pack so you can compare others on here that will fit the Flux battery boxes). I have used the packs on my Flux and they work well and only puffed a little after heavy use the Flux throws at it. I tested the Turnigy 5000mAh 3S 25C Lipo Pack your looking at on this page in the Flux box before and the lid doesn't shut due to the little bit extra width and height they have as the sides hit the cover. I'm using the Desert Boy 17 TVP's so I mount all my packs inside the chassis that's how I can use these batteries.

 Gustavo 28 points

this slim pack will fit in all radios that use 8AA batteries.

 Danen 10 points

Yes it will fit in the Savage flux. I removed the tops of the battery boxes and just use two straps of velcro all the way around to hold them in. One strap even fits perfect into the old plastic clip holder. Just make sure you have the foam in as well and you are good to go. The battery box on the savage flux is a ***r design and most people use velcro straps of some kind to help out.

 Coy 16 points

i've seen people with this battery, not sure if it needed to be modded

 Henky 5 points

yes it is

 MasterB 105 points

Yes, but you may need to remove the foams to close the lid.

 E-Conversion 27 points

You need a lipo compatible charger (GET ONE WITH A INDIVIDUAL CELL BALLANCER!) In fact, hobby king sells some really good ones so click on batteries and at the bottom of the the list the is 'chargers' over there you can find lot of good ones, I will be getting this: www.link the connector, you will have to buy a connector for a 4mm bullet plug to the traxxas plug or you can solder either the battery or the esc to get a fitting connector (if the battery, solder the traxxas plug on, or if its the esc solder 4mm bullet plugs on) Hope this helps and remember to get this too: www.link

 cireone 7 points

Thanks, I appreciate it.

 nen27 26 points

muy buenas para el mentor de multiplex te brinda mucha potencia y ademas mas horas de vuelo

 Lata2002 9 points

You can get the IMAX charger discharger and balancer. Any lipo charger that has an AMP of the size for your lipos batteries. I mean if you have a 5000mah lipo batteries you should have a charger with 5.0A rate or higher.
The connector for Slash is traxxas connector. but you can buy an adapter for it
thx

 Gustavo 28 points

I'd suggest a great charger from TURNIGY. Product ID Accucel8150

 Danen 10 points

I use the Turnigy A-6, I have the old one that only did 5A max. So the new one at the link here will charge them just a little faster. And i would just use the Traxxas High Voltage plugs for it, they work very well. Any of the Turnigy Lipos, will be a direct fit on the balance plug for the turnigy chargers.
www.link

 Coy 16 points

well from experiance, this pack may not even fit the slash, it doesn't fit the 4x4 or the rustler stampede bandit. if you have ordered it, you will need a traxxas high current connector. Any charger lipo compatible that can put out around 6 amps is most efficiant for this battery. Hope this helped.

 savage xl 3 points

Yes they fit but the lids dont close so I also use velcro straps. I would caution these packs as I had one swell after the first use. It cost more to ship it back for warrenty than a new pack costs!!! :-(

 nen27 26 points

muy buenas para el mentor de multiplex te brinda mucha potencia y ademas mas horas de vuelo

 Coy 16 points

Theres a way that you can put them. You need to slide the bottom corner of the pack into the tray, then slide it back as far as you can. Then simply take some electric tape and wrap it around the whole chassis right in front of the antennae. You can also take a 1 or 2 foot long piece of Velcro and cut the chassis where the lip on the side forms a right angle with the chassis deck, still in front of the antennae on both sides, and loop it so that it secures the battery.

 Joseph 10 points

i cut mine off and solder on the ones i wanted it wasn't that bad

 Nigel 9 points

yeah i did the same...just have to be careful of short circuits!

 spitfire2010 640 points

Cut it off but take care to cut one wire at a time. Sounds silly bit I've seen it done BANG!

 Peter 8 points

Good battery. took 4 pieces for his e-revo. the size of the wires sticking out a bit. so I had to solder them suddenly at the side of the battery. But after everything was super.

 Richard 5 points

Cutttttttttttttt offffffffffffffff

 Danen 10 points

Cut them off, and start new. You could make an adaptor for them, but it would just add weight and resistance that is not needed.

 Coy 16 points

I havent seen any adaptor for the bullet conectors so soldering would be the best way to go. (make sure you cut ony wire at a time so they dont short)

 savage xl 3 points

If you change the ends I am led to believe that it will void your warrenty

 Michael 1 points

Does anybody have a declaration of (CE)conformity, prferably in German? If yes, please answer me and upload it. I need one to get my order at the custom office. It is urgent. Thank you very much.

 Almm# 1 points

cut off dude, you'll not have any kind of problem with that

 Coy 16 points

yeah I used them on a traxxas spartan. Great batteries

 Almm# 1 points

this batterys its so good man, had a lot of autonomy

 Joseph 10 points

yes it will with a little trimming for the wires

 Lata2002 9 points

no, it wont fit on that.
ITs for a revo or a t-maxx.
thx

 Coy 16 points

it wont. However you can wedge it into the tray and tape the part sticking out. The only problem is that the discharge rate is possible to fry your esc

 steve 56 points

sorry for the spellng just worked a 14 hour day

 Joseph 10 points

with a little work they fit just fine

 Lata2002 9 points

yes, those are bigger than the rustler
thx

 Coy 16 points

no, too long. plus discharge rate can damage speed vxl esc

 Joao Paulo Francis 1 points

Exelente bateria, uso no meu traxxas E-Revo e roda 100pcnt Alto torque alta duração com bons carregadores. recomendo a todos a HobbyKing Excellent battery, use it on my traxxas E-revo and runs 100pcnt High torque high boots with good length. I recommend everyone to HobbyKing

 Coy 16 points

this battery wont fit. The dimentions accually come out to be around 53 mm wide.

 Joao Paulo Francis 1 points

Exelente bateria, uso no meu traxxas E-Revo e roda 100pcnt Alto torque alta duração com bons carregadores. recomendo a todos a HobbyKing Excellent battery, use it on my traxxas E-revo and runs 100pcnt High torque high boots with good length. I recommend everyone to HobbyKing

 Danen 10 points

I have just started using the Castle Creations 6.5mm bullets. I love them, and they support 200A. I have used deans in the past, but the were getting warm on my Savage flux so i wanted to upgrade. I strongly recomend the 6.5 Castle Creations Bullets

 Coy 16 points

I use traxxas, when you solder it, put some heat shrink tubing around the part where the connector and wire are soldered. It will compact the wires therefore making it easier to assembled.

 Joao Paulo Francis 1 points

Exelente bateria, uso no meu traxxas E-Revo e roda 100pcnt Alto torque alta duração com bons carregadores. recomendo a todos a HobbyKing Excellent battery, use it on my traxxas E-revo and runs 100pcnt High torque high boots with good length. I recommend everyone to HobbyKing

 Coy 16 points

www.link agreed

 山田 1 points

?????????????????????

 Clint 68 points

I just trimmed a little bit out of each battery door. Nothing major just a bit and they work perfect.. I swear they run just like my maxamps, you cant tell the difference.

 Coy 16 points

if your talking about the erevo, its definitely worth it. it does nothing to effect durability and all you need is 1 square inch out of the door

 Sean 28 points

Clint you are correct... the batteries fit perfect* HOWEVER the wires are so fat that the battery door doesnt want to close... you will have to trim off the top rear of each side of the battery trays to get the doors to completely fit. i havent put ends on mind just yet, so i dont know how the performance of the batteries are.

 Clint 68 points

I been running these Turnigy 11.1v 5000mah 25 c and they perform awesome. I also have maxamps 11.1v 5250 mah 30c lipos and I cant tell the difference performance wise between the two no joke.

 Neu_racer 33 points

I am a MaxAmps dealer and since this is fairly anonymous I will say compared to them, these are just as good if not better in every way, Performance is amazing, price is unbeatable, and they have a pretty long life. I have 2 of these batteries and running them in series in a MMM 2200 powered Revo makes it haul ***
I will never buy another MaxAmps battery as long as I live. But if anyone doesn't share my sentiment I will help you out. *-)

 Sean 28 points

I am also a Max amps dealer and since their price increase last year i have stopped ordering from them and started ordering from hobby city. the performance and quality seems to be the same if not better with the Zippy's and Turnigy's

 Coy 16 points

Just make a 1 square inch hole where the leads extend from the battery. It does not effect the strength and it will close perfectly. Used it on mine for 7 months without any issues

 Coy 16 points

The burst is under rated. its more like 35-40c

 Clint 68 points

Zippy is soon to be discontinued.

 Richard 5 points

Just as good.

 Danen 10 points

I think the turnigys are a little better pack. Most have a high C-charge rate. I have both Zippys and Turnigys and both work great. But the Turnigys can be charged at 5c where my zippys are 1c

 Coy 16 points

I think perhaps its near identical