USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
2.4GHz receiver for Assan X8 systems.
Compatible with all X8 transmitters.
Size: 36 X 14 X 3mm (1.97 X 1.02 X 0.39 inch)
Weight: 2.8g
Key Features -Highly secure and robust link
-No crystals or channels needed
-No interferance from motors, ignitions or metal to metal friction.
-Short antenna
-No need to change any settings on your radio.
-Works with all X8 systems.
MagnusE, Congratulations in posting the most rude reply I have ever read . Are you not aware that some manufacturers make statements that are not allways the complete truth.
Soory if you feel offended, i will stop posting replys like that.... But it is strange that the same Q comes up over and over again. There is many replys that says " it is only working with assan module", dont you think that is the truthe?
You must use Assan module in the transmitter. You can change the modul in your transmitter to this www.link you can use every Assan reciver including this one. //Magnus
I have flysky modul.(t is same turnigy 2.4 modul)Can I use assan 2.4 ghz 4ch receiver with this flysky modul..or should I use assan module to use assan mini recieiver..Pls answer..
I'd say 1S and 3 volts from UBEC or ESC for i fried my X8 R4 4Ch 2.4GHz Receiver (Mini JST plug) with 4 volts now I'm waiting for another 1 to get here
I think the jst connector from this harness kit will work. If so, use it to make your own adapters. AM4020 - Tamiya Female w/ JST-XH 2S Harness for Hard case Lipo
4/28/2009 The wire is the binding plug. Look at the setup carefully* lay the cable flat and you will see the terminal positions, black wire and red wire cross over and both connectors are same type so it is not used as an extension cable. This will connect 2 signal pins together which is the procedure for binding the receiver to your transmitter.
2/25/2009 Nowinkk, Some ultra light models that are RTF have this mini JST connector. This Assan rx will allow you to change to 2.4GHz.
I have not located the mini JST connector in Hobby City servos yet. A wire with mini JST connector on one end and open wire on the other is available from Tower Hobbies thru Futaba (rather costly piece of wire* about $5). JR and Futaba currently have servos with the mini JST connectors. Some people also refer to this connector as a micro connector.
This JST connector might be available thru your local electronics store. You can also search the JST website <***********jst****/index.html> You will need to measure the pin separation referred to as the pitch and pin size. JST is likely to be the source for connectors used in RC hobby. Hope this helps you. Aloha
The polarity is, from left to right looking at the pic above: positive (+), negative (-) and signal. That is the same polarity as my BlueArrow 2,5g servo that i purchased from HobbyKing.
I would buy this rcvr if I could find servos with the mini jst plug. I looked thru all the servos* found no mention of this plug. Also went thru all the plug listing* and did not find this plug. davei
Very nice receiver, excellent build quality, there's only one little issue with it and it's that there's a mistake in the pin label on the back, there are two circles, black and red and a signal icon. Both the black and red circles have a "plus" symbol inside, follow the colours not the symbol for wiring.
No comments. Reply..
Overall Rating
aeronot
60 likes
Value
UNRATED
Quality
UNRATED
6 thumbs up!
Hello all. I have been using the micor JST now for lots of things. You can get the plug housings and pins from Digi-Key. Here are the part numbers.
servo lead housing: 455-1160-ND pins for 26-28 awg: 455-1130-1-ND pins for 28-32 awg: 455-1281-1-ND female connector: 455-1658-ND
Greate little reciver. Weight as advertised, 2,8g. With removed shrink tube,glass fibre "stiffener" and the plastic conector seats the weight is down to 1,86g. It does work with one LiPo cell, but below 3,5 v it starting to behave strange, and "mixes" throtel with elevator... I would recomend to tape the antenna to the board to prevent it from coming loose. Super reciver to use in shock flyers, and if you are using BA 2,5g servo it have the right conector. (1,5mm pitch) Magnus
No comments. Reply..
Overall Rating
Zwitold
10 likes
Value
UNRATED
Quality
UNRATED
1 thumbs up!
Installed in electrified fox from multiplex. Excellent light receiver. Only one issue - can hobbycity have plugs for this receiver? I ordered from e-bay but be better if hobbycity have this in stock.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg){kind=small}
.jpg)
.jpg)
.jpeg)
