Please confirm your location:


USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Electric Motors > All Outrunner Motors
> Electric Motors > TURNIGY
> Electric Motors > Outrunners by size > 28 to 34mm

  RATED:

Turnigy2836 Brushless Outrunner 1000kv

Turnigy2836 Brushless Outrunner 1000kv

Dimension: 28mm x 37mm, 55mm(with shaft)
Weight: 80g  (kv1000) (not including connectors)
Diameter of shaft: 4mm
Length of front shaft: 14mm
Lamination thickness: .2mm
Magnet type: 45SH

Max performance
Voltage: 3S
Prop: EP10x5
Thrust: 1000g
Power: 300W
For
800-1000g 3D
1200g+ Trainer





PRODUCT ID: T2836-1000

This product available from a warehouse near you!

Kv(rpm/v) 1000
Weight (g) 80
Max Current(A) 27
Resistance(mh) 0
Max Voltage(V) 11
Power(W) 300
Shaft A (mm) 4
Length B (mm) 37
Diameter C (mm) 28
Can Length (mm) 22
Total Length E (mm) 58
Update/Add my own data
Customer Data

Weight: 137g
Quantity: 
International Warehouse
stock
10+
USA West Warehouse In Stock View Item
USA East Warehouse In Stock View Item
Price  $20.00

Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
5110
crowns
  
 
Total of 51 discussions.
Eric  4 points - 4/26/2015
 
I use this engine for two Easyglider . One of them flies for over 4 years with ! No worries ! Lipo 3S, 10X4 propeller and controller 30A Good power , I made ​* glider towing with : D
Butzi56  11 points - 4/7/2015
 
I'm using this motor in a Staufenbiel 'Cougar' 1.4m Hotliner and coupled with a Graupner 11" x 6" folding prop, Vladimir's HyperSpinner (with cranked yoke), 50A ESC and a 2200mAh 3s LiPo it easily drags the 825g airframe vertical. The motor only gets Luke warm as it's only used in short bursts of less than 15 seconds. Static current drain in my configuration is 33.4A ( about 355 Watts) Highly recommended.
Luis Miguel  1 points - 12/14/2014
 
Can I use a 4s Lipoly?.
 chopper50 392 points
Hi Luis, you can use 4s but you will have to use a smaller prop to keep the watts and amps down please use a watt/amp meter something like PRODUCT ID: HK-010 keep the watts around 300
__Erni  9 points - 5/23/2014
 
I use this motor in my Phoenix 2000 glider with a 40 A Turnigy plush ESC. Very good and plenty power with the prop that comes with the Phoenix, which I belive is a 10x6 (no numbers on the blades) It fits the supplied motor mounts without modifoications
 juweeltje 65 points
Erni, stil happy whit the combo phoenix2000 this motor ans esc?
SilbernerSurfer  113 points - 4/8/2014
 
Replacement shaft available for this motor?
 chopper50 392 points
Hi, you can use PRODUCT ID: SHT009 i use these on all sorts of motors have a look see what you think 4mm x 60mm
Customer Reviews
Overall Rating
zcv7853
88 likes
ValueUNRATED
QualityUNRATED
8 thumbs up!
UPDATE!!!!

I was flying most of the time at less than half throttle with no heat problems. Flying full throttle for plus10 seconds overheated the esc and it went into thermal shutdown. No harm done to the plane, but grab a 30amp esc and play it safe!!!


3 comments. Reply..

Overall Rating
Andariel
156 likes
ValueUNRATED
QualityUNRATED
7 thumbs up!
Super motor, good quality, installed in Multiplex Parkmaster 3D, Turnigy 18A Plush ESC, Zipppy 1300mAh 3s 20C, flight time about 7minutes with super performance, the same motor planned to use with Multiplex Geminy, 30A Turnigy Plush ESC and 1800mAh Zippy Flightmax 3S 20C battery. Thanks hobbycity for motor with higher KV than others.


5 comments. Reply..

Overall Rating
lifelaffer
126 likes
ValueUNRATED
QualityUNRATED
7 thumbs up!
Very pretty and powerful little motor! Full set of hardware and etc too! The shaft will reverse if you do not want it at base(wire end), I used, as sent, in glider with 10x5 folder and 1450Zippy H and pulled about 20 amp static and 210 watts. Lots of pull and 60deg climb. Reversed shaft and put in 20oz bipe and used same battery and a 11x3.8 SF for 3D and pulled 25 amps and 267watts. Hover under half throttle! Motor cool on both apps. VERY NICE!


4 comments. Reply..

Overall Rating
Andariel
156 likes
ValueUNRATED
QualityUNRATED
5 thumbs up!
Super motor, good quality, installed in Multiplex Parkmaster 3D, Turnigy 18A Plush ESC, Zipppy 1300mAh 3s 20C, flight time about 7minutes with super performance, the same motor planned to use with Multiplex Geminy, 30A Turnigy Plush ESC and 1800mAh Zippy Flightmax 3S 20C battery. Thanks hobbycity for motor with higher KV than others.


2 comments. Reply..

Create an account
Overall Rating
raptor
1690 likes
ValueUNRATED
QualityUNRATED
4 thumbs up!
3S1P plus 11*4.7 = 19A 80Celsius(TURNS) & 45Celsius(MAGNET)
GOOD 5 STARS!!!


3 comments. Reply..

.....click here to see all reviews
Aff. Link