Rhino 610mAh 2S 7.4v 20C Lipoly Pack

 srepfler 1111 points

Yes, XT60 - JST Female in-line power adapter PRODUCT ID: XT60-JSTF

 srepfler 1111 points

1.2 A,capacity times charge rate. best to charge 0.6A.

 stefano 14 points

io le lipi le carico sempre con una corrente inferiore del 25% della loro capacita 600 meno 25% quindi a 450 ma

 lazorus 6 points

Yes. It fits perfectly.

 straton 224 points

hobbyking keeps deleting my review (2 crowns) One battery out of two, died by itself even though it was never used!!!

 Gary 2959 points

Maybe ok but getting a bit heavy.

 jteee 241 points

jreiung, why are you asking the same question for EVERY battery HK sells?
If one battery is too large/heavy, why ask the same question for larger/heavier batteries?

 iflylilplanes 266 points

I've been using 3 of these for 6 months now, each pack is flown and charged min 4 times a week weather permitting, and no issues have arisen. Enjoy the 2 packs you have try the third if it has issues bin it , at the price it would cost more in postage than its worth to pursue it with HK.

 The General - x5 139 points

I've had 4 cycles since on that bubbly pack, checked the cells and they were within .25 volts of each other. So no apparent issues with the bubbly cell after discharge.

 iflylilplanes 266 points

Good to hear,just watch the temp. I ran my 3 packs again today in a HK 3D Hawk, the packs got warm with a 5 minute run each, that's OK. If your puff pack gets to hot keep an eye on it and always be wary of all Lipo batteries good ones as well, they are known to be unpredictable.

 unicorn 17 points

If the li-po is swolen replace or ditch it, cause they are not safe and you are waiting for troubles.. Those few usd are not worth destroying rc model or worse your garage...

 MrRCFlyyer 744 points

Yes but make sure it is pluggled into a LIPOLYMer battery charger before connecting the balance and charge port to the charger. All Li-Polymer batteries require a recommended Li-Polymer charger to charge it.

 Marcin W 5 points

Very gut battery. Mala lekka i wytrzymala.

 soloman572000 87 points

It is enought. But never use more than 2C (1,2 Amp) ti charge this lipo. Use only Charger with balancer with Lipo program I reccomend this Turnigy Accucel-6 50W 6A Balancer/Charger w/ accessories PRODUCT ID: ACC6 But you can also use simple lipo charger like this www.link

 MrRCFlyyer 744 points

Hi, 2c is for charging and 4c is the max charge rating. Tip of the day: Never charge any batteries over 5C or 4.6 C to be exact.

 Marcin W 5 points

Polecam. Bardzo malutki lekki pakiecik.

 Arch.Pham 1 points

You can charge with 2c for the best. Remember to use balancer pack with each.

 PILOTO-SP 65 points

You will need a lipo charger that is right here that looks very good and great prices www.link

 Indula 1 points

Thanks but that site took me to some simulation and training page.... Did you misspell it?

 PILOTO-SP 65 points

sorry I translate on google, look at that link now www.link

 EKflyer 5 points

You will also most likely need a ~12 volt AC/DC power supply to power the charger depending on which one you choose. Some chargers have built in AC power capabilities but for most you will need a power supply.

 Paul 11 points

LIPO batteries ask for a specialized charger. So, you can use that kind of 'multi-purpose' www.link a such charger you 'll be able to charge other types of battery safely. No overload worst for any battery.

 ANDY in c.a.p 329 points

hk 50w 1sto6s charger

 Werner 10 points

ich fliege sie in einem felix von Miniprop mit einem 7gramm motor und einer 5x3 GWS. Dabei zieht der motor ca. 3,5A

 rwmusik 9 points

Maximal 12,2A Spitzenlast. (20X610mah) 10A Dauerlast dürften kein Problem darstellen.

 enzie 135 points

Habe mal einen Testlauf mit einem Turnigy 2836/3700kv, 72g, 700Watt gemacht.
Luftschraube : 6x4
Dauerbelastung : 10 Amp
mehrere Spitzen von 20 Amp (jeweils ca 2-4 sec )
max. Leistung : 120 Watt
Gesamtlaufzeit ca. 4 min.
Keine Probleme, alles im gruenen Bereich.
Alle Daten mit Wattmeter gemessen.

 enzie 135 points

here in english :
make a testrun with Turnigy 2836/3700kv, 72g, 700Watt.
Prop : 6x4
constant discharge : 10 amp
some peaks with 20 amp (each 2-4 sec)
max power : 120 watt
total runtime : about 4 min
no probs
measurements done with "WATTS´UP" .

 aero2k4 12 points

Die normale Entladung der Batterie ist 20C, mit kurzen Spitzen niedriger als 30C. Wie in anderen LiPo-Akkus, ist es empfehlenswert, dass die Gebühren bei 1C. Für die 610mAh Ladegerät gesetzt 1C Ladung sollte 0.6A werden. Ich hoffe, das war es, dass Sie gefragt!

 Christoph 49 points

If you know how much Amp. the motor needs, you can calculate the flight time. Otherwise we can´t help you.

 a.aniol@gmx.de 25 points

i fly this Lipo in a 180g Comicflyer (kleiner Drachen) for 10 minutes with 6x4 Prop

 Werner 10 points

The Flight time is about 12-15 minutes at 5A and a flying weight of about 100gramm. The engine is a 5x3 with a 7gramm Prop.

 thedocmaster 10 points

It depends on the weight of the model and your prop too. I use it on a self-built 3d indoor plane and gives me good power during about 7 minutes.

 MarAker 10 points

It depends on your flying and motor. mine are empty after 4-5 min. thees batteries must be maintained well if not they will turn bad fast. don't empty them, shuld be about 20-30 left. use a charger with storing function

 alexaglob 3 points

7 minutes on a flybarless Firefox 200, weight with battery around 230 grams

 Pablo 1 points

con un AXI 2208, avion 300gr, tiempo de vuelo 7minutos

 Rafael 5 points

The time of duration is proportional at the use mode...if you use with a 3d flight, 5 a 7 min...if you use in a economical flhigt, 10 minutes...

 goh 19 points

depends on the operating voltage. for this is 7.4v

 nikwal 64 points

0.61*20= 12A = more than enough for most servos and reciever..

 Zebra 12 points

Hi! I am using this with a brushless motor, a receiver and 3 servos. Regards,

 Matthias 1 points

Yes, it can. But only with a UBEC!! Dont connect it without a UBEC on the receiver!

 kingwang 3 points

why not? but it's depend on the heli

 ABUBAKAR 92 points

yes if u r using a regulator with this battery! bcz most of the receivers holds only 6.6v while servos only 6v so u use a ubec with it bt keep in mind the ampssss!!! greater the amps

 joeham 8 points

No, this has wrong currency for a receiver. A receiver must not have more than 6 Volts. You require an UBEC to reduce currency, then it will work fine.

 gordonmcw 12 points

I've used these batteries with the Turnigy 3A UBEC to run a receiver and 4 standard analog servos with no problems. The UBEC is selectable (5V or 6V output) and the combo has been working well

 Polleke 14 points

No the voltage of 7.4 volts is to much for your receiver. You're gonna blow up your RX.

 mattio79 120 points

only if they are capable of handling high voltage. most receivers and servos can only handle up to 6v or so.

 kellan 7 points

yes it can.

 Spark29 12 points

have they arrived?

 LaserBeam 744 points

You think you've got problems? I bought a plane, some LEDs, some pilots, some recievers and other bits and ALL WERE IN STOCK at the time i paid. Twenty days later and my order is still PROCESSING. So when they say the item has been RESERVED for your order, they're pissing straight into your pocket. Thank you, HK. Is this my reward for going Platinum?

 LaserBeam 744 points

In hindsight, im always happy when the HK packages arrive. Big orders make me anxious :)

 LaserBeam 744 points

Hiya, the battery is in the post and on the way so i am happy. Maybe the Chinese New Year celebrations caused the delay. So im taking back what i said before about pockets :) The Li-Po is cool.

 tchez 110 points

They are in stock now.

 jteee 241 points

in stock now

 earthling1984 25 points

yes this battery uses a JST plug for connection to your ESC.

 gratefulfrog 11 points

the discharge plug is male jst.

 Alexandre 9 points

No it's a male plug !!!

 gratefulfrog 11 points

it's a male jst discharge plug and male balaance plug.

 pabloramos 31 points

Mine came with a male plug. Ordered a pack of JST plugs and soldered a female on the esc

 joeham 8 points

Mine had JST male plugs.

 ABUBAKAR 92 points

the balancer plug is jst-xh male n the battery connector is also a jst male

 mattio79 120 points

no, it is male. the female is what it goes inside of. the male has sockets and goes inside, the female has pins and covers the male. kinda backwards if you ask me, but then again it is cheaper to do it that way.

 mbullick 40 points

51mm x 30mm x 11 Not including any wires.

 Corleone 116 points

A 52mm (Without cable) B 30-30.5mm C 11mm (12mm at the end due to the foam)

 MustangTom 26 points

real weight 36 gr.

 mark 1 points

It fits the orange tx perfectly

 Beaufighter 1808 points

Probably because they haven't got any delivery date. It usually is. Just wait 'til it is in stock and then order:)

 Corleone 116 points

I had no problem ordering on these, when they were on backorder.

 Stephen 2 points

You shouldn't have issues placing items that are on backorder in your cart, or at least I've never had that occur before. Long live the Brotherhood!