USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
This is an archived page. This product is no longer available and has been replaced by a newer product.
Why link it to the category: Multi-Rotors & Parts?
Could use an engine like this...
On a car I don´t know.... but I used this motor in my fun jet with a 100a ESC and both burnt.... :(
One thing for shure the engine is very powerfull and the burning part was my fault I pushed it too much....
Just bought the XL for 90mm ducted fan, burn out the "Turnigy Super Brain 80A Brushless ESC" at first s***l up. What went wrong?. I'm using 6s 4900mh battery pack.
try programing your speed control with a smaller battery i have done the same thing now when i program i use a small kv motor and a small batt before going full bore and it works great
What do the L and XL motors afford you, in terms of performance, versus the S if they all share the same spec's. I bought one of the L models from someone, advertised as being for 1/8 scale buggies. Is this an accurate description?
does anyone know the difference between the s,l,xl i figured the s is like a 540 can size but whats the length of the l and the xl iam looking for a 550 can size motor
hello, need to know the maximum voltage I can use with this engine. I use this motor in a ducted fun 3.5 "with a 3s lipo in and wonders whether it is possible and what is the maximum voltage? if anyone knows answer to this, was very grateful. thanks
RPM on 22.2v would be 130,000+. I don't think it will last very long at that speed.
Volts x kv = rpm 40,000-50,000rpm would be the ideal range for power and efficiency. 60,000rpm will be more powerful but less efficient. I wouldn't recommend going above 60,000rpm.
It is a 6 turn motor. KD - manufacturer/model 36 - diameter in millimeters 50 - length in millimeters 06 - 6 turn motor S - 'S' can motor (length determines the can size)
i just received this powerplant and tested it with turnigy plush 80A esc and zippy 3s1p 1500mAh.
found that when running free(no blade and no drive shaft attached) within two minutes only , the motor get too hot and hardly to touch. no water jacket applied to this motor.
i have yet to test it with my new lipo zippy 3s1p 3500mAh 30c~40c due to this overheated problem.
IS THIS CONDITION IS NORMAL IN YOUR LAB TESTING OR ELSE? WHAT COULD THAT HAS HAPPENED?
Any brushless motor will quickly heat up if there is no load placed on the motor when it is running. If you do this too much you will most likely damage the motor (demagnetisation will start at around 200 degrees fahrenheit).
I do not know, if this is still relevant, but I also had similar problem, I was not able to find 0.6mod 5mm pinion (for tamiya) until I found out that trex-500 heli uses exactly the pinion I need *-)
Just order this one of the ALIGN pinions (10T-17T). If you need other sizes you can get them from various companies, just google for "revco pinion".
@kuntaw- This will not fit any 1/18 scale car and a 25A esc will not be able to handle it. I would suggest using the KDA 20-30 19Turn S Brushless Inrunner 4,900kv www.link or the KB20-30-18S 5200kv Brushless Motor www.link
Customer Reviews
Overall Rating
Matej Krof
likes
Value
UNRATED
Quality
UNRATED
24 thumbs up!
I had this motor in my tamiya ta05. it was perfect. very fast, and motor was cca 20° on 6nimh 4200mah. if are you searching a motor for 1:10 cars offroad or onroad this is the perfect choice... just watch that you have enough powerful battery-this motor is for big currents..
No comments. Reply..
Overall Rating
customer
337 likes
Value
UNRATED
Quality
UNRATED
8 thumbs up!
god motor for fast cars.. all the kedas run great for speedruns. i got this one up to 119kmt/ 74mph in a rustler vxl with 3cells. motor burned my vxl esc but motor is still god as new ) handles more than 176A in peak in www.link to try with mamba max esc, and hope for better result
2 comments. Reply..
Overall Rating
spyspeed
43 likes
Value
UNRATED
Quality
UNRATED
7 thumbs up!
if for car aplication how about the ESC that is working with this motor? must use ESC special for car or can i use airplane esc?
1 comment. Reply..
Overall Rating
Stewart
18 likes
Value
UNRATED
Quality
UNRATED
4 thumbs up!
My son has used this motor in his RC Funny car for drag racing used it with a Mamba Monster speed controller with 6s and has run 1.5 sec and top speed of 165 kmh in 40 mtrs. The Mamba motors have a tendancy to snap their 3mm shafts I have done 2 Mamba motors in on 3s. I have decide to use 2 of these motors in my 2 drag cars, with the 5mm shaft no more trouble with snapped shafts. should have no problem even when using 4s.
6 comments. Reply..
Overall Rating
Customer
18 likes
Value
UNRATED
Quality
UNRATED
3 thumbs up!
I have used this motor for Drag racing in a 1/10 rail on with a 5000 40c Thunderpower 3s and it ran in 40 mtr 139.8 kmh and the time of 1.483 seconds my personal best time. Great motor with the 5mm shaft no worries about snapping the armature like the Mamba Max motors.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg)
