USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
Throw away your crystals, say goodbye to glitches! The new Corona synthesized receiver is here! This unit will work with existing Synthesized transmitters or crystal transmitters. In fact the accuracy of this receiver will improve the performance of all 35mhz crystal transmitters.
Spec. Sensitivity about 2.0ìV Selectivity ±8kHz at 65dB down Number of channels 1-6 Filtering Dual turned RF circuitry Filtering Dual 4 pole ceramic filter Filtering DSP filtering with mild algorithm Shift polarity Positive or negative (auto-detect) Case Shrink wrap Operating Voltage 4.8V~6.0VDC OperatingCurrent 20mA Modulate FM/PPM(pulse position modulation)
*(version2) unit has been revised with the following resolutions; -Increased binding with various branded radios. -Corrected servo locking issue. -Corrected Channel 2 jitter issue when used with certain Transmitters.
*The image shows Dual conversion, on the package. The image is of the beta-version which had the wrong packaging. We will update images soon.
Hello, just to say a Futaba 6ch transmitter with crystal 35.270mhz txa, after take in setting the frequency, servos not respond well to the radio near the receiver, once at the airfield in the distance seemed to work until long distacia lose the signal, so I smashed the plane, getting off nice failsafe activated.
I do not say that to other radios and / or crystals go well, but if that is true that is not 100% compatible.
I have the same transmitter and channel (76). It works, but I noticed slight servo noise from interference sometimes. The RP6D1 seems to be better as I said few discussions back.
Cannot figure this - have Futaba Tx6EXP trannie, so power up system get 2 blinks press button, get 3 blinks-indicating ready to scan - enter mode one blinks twice press button while in mode button to scan and then NOTHING and no lock - what am I doing wrong? TX is on ch62
At power up you get two blinks like you said. Then press the button for 2 seconds to get three blinks and that is mode one. Now you have to press the button shortly to get rapid blinking (scan). If you get two blinks before scanning you have to start over. Just try it few times. The led has to stay lit after scanning. I tried several times myself until I got it working.
Thanks Bertil have sucess now - you will see that instruction file online here at HK is slightly different procedure from the printed instruction paper that comes with RX. Guess it's just bad translation from the orginal Chinese HK always comes up short with manuals and instructions for products this forum is the only way we modelers can resolve problems with products.So thanks for youconcern and help. Cheers Robcoxon
There should be no problems with IC planes, but I suggest getting RP6D1 instead, because it has performed a lot better in my experience. I am shure it is compatible with your transmitter PPM modulation. Probably it will not work when you select PCM.
i think this rx is only for synthesized transmissors
i have one and there's a button to scan frequencies but maybe if your tx is for example 35.870 and you push "scan" it will detect your transmissor but i haven't proved, i hope someone will solve this question this is all I can say
I have one of these and If your transmitter is 35 MHZ then it will work. This works with all 35MHZ transmitters. I have a very old one too and it works great.
can i use it with my E sky 35 mhz 4 ch 0404 transmitter? and stock 35.200 transmitter xtal? i have 6ch esky rx but range is too low. if i bought this corona can i use it 1 km without glitch or range problem. (i will use it on 900 mhx 200 mw fpv downlink)
I have a 35MHZ transmitter with 35.150 X'TAL and it works perfectly. No glitches, adapted to frequency quickly. It should work with 35.200 as well. If your transmitter is capable of 1km range then the receiver should work at that range too :)
hi o have also some of the coronas. i made a range test with the original antenna and get signal in 2km. for a new fpv plane we replaced the antenna, the new one is about 428cm (168,5 inch) long. we will test it the next few days and hope to have more than 5km range
35.160 is channel 76. I have used this with Multiplex Transmitter with channel 61 and 70 and it worked great. You can not use this with PCM systems just PPM.
Channel of throttle is dependant on your transmitter. I have the same product and as standard when it looses signal the power does ramp up.. HOWEVER..im sure it does have a built in failsafe so I would proper configuration will solve this. I will try and give it a go and get back to you.
hola tengo problemas con 2 receptores como este, yo creo que es el v1, el problema sucede con el gyro futaba 401, cuando muevo stick alabeo-cabeceo parpadea el giro perdiendo el centro, con otros receptores no pasa
Hola* tengo que decirte que yo he estado usando otros dos como este con una "HITEC Eclipse 7" y funciona de maravilla. Siempre habia tenido problemas de incompatibilidades con esta Emisora. Con estos receptores no
Use this receiver in a Parkzone T-28, 50 flights +. All 6 channels are used (flaps).
No subjective difference to my other receivers (Graupner SMC 16 Scan). Had no glitches yet and it seems like it includes a Failsafe-programming (mentioned in the manual)!
Receiver is much lighter and has smaller dimensions than other receivers.
Neg: Manual and binding is nothing for a beginner, its a little bit tricky to bind the receiver and activate the Fail-Hold function. The body of the receiver is a kind of paper (leightweight!) but not very stable. The diameter of the antenna is a little bit flumsy.
just unpacked box and i see - singl conversion rp6s1. in the description above we see - dual conversion... what this??? rx can't connect with hitec optic 6 dual conversion!!! why hobbycity cheating?
What`s the differens RP6S1 vs.RP6D1? I thougt it was Singel vs Dual conversion, but the label on the RP6S1 says "Dual conversion...
Customer Reviews
Overall Rating
Atle Saetaberget
likes
Value
UNRATED
Quality
UNRATED
20 thumbs up!
Received this item today, have not tested it in the field yet. Is labeled "dual conversion" but guess its a single one.. (take a look in the community section). Locks quickly to my 2 available freq (ch 66 and 68 with futaba 7CAP). Tried a quick "range test" in my house (walked around in different floors with concrete walls) - perfoms well but the 8ch dual conversion type performs better (thats way I thisnk its an single conv). Have not tested how its performing reg. the centering issue yet.. A good 4 star for now.
No comments. Reply..
Overall Rating
roger carlsson
likes
Value
UNRATED
Quality
UNRATED
18 thumbs up!
The best receiver i ever get!
No more glitches with these receiver. I have ordered two more. Highly rekommended!
No comments. Reply..
Overall Rating
Hans Högbäck
likes
Value
UNRATED
Quality
UNRATED
15 thumbs up!
Easy to use and no problems with setup...
Radio Hitec Optic 6 and Optic 6 Sport, works perfectly with this Corona receiver
Lätt att använda och programmera...
Fungerar perfekt med Optic 6 och Optic 6 Sport.
No comments. Reply..
Overall Rating
Paul Crane
likes
Value
UNRATED
Quality
UNRATED
12 thumbs up!
Tried this receiver today in a wing with a Evo 9 transmitter and am happy to report no problems found with no glitching. I did find the hole used to press the synch button through the case to be slightly off although this was not a problem and it did lock on to my channel quickly. The only thing I have concerns about is that the aerial is a bit thin.
No comments. Reply..
Overall Rating
Thomas Lindqvist
likes
Value
UNRATED
Quality
UNRATED
9 thumbs up!
This little receiver works great with one exception. It doesn't seem to lock on to the selected channel and start delivering a signal to the servos fast enough for my gyro to consider the transmitter being powered up. This makes it hard to use in a helicopter.
On the other hand, it is easily set up and has excellent range for it's size and most of all, it's price.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg)
.jpg){kind=small}
.jpg){kind=small}
.jpg)
