I've been waiting on this for 2 weeks and it is holding up my whole order. I purchased this to go into a phoenix 2000 glider. Can anyone recommend an alternative to this motor? It could be more or less expensive... just as long as it is in stock.
I'm confused on thrust output... At the top of the description it shows 'Combined with a 10x6 E-prop this motor can push out over 1000g in thrust on a 3S1P configuration lipo' yet in the suggested props list it shows '11.1V 16.7A 1060 650g'.... So which one is it?
Thanks for pointing that out, totally missed that LoL. I was looking only at the 10" specs. Trouble is that in drive calc, with voltage constant set at 11.1v, max eff on this thing is 77% * 7a... By the time you get upto the load a 1060 prop will put on it you're looking at 16-17a & an eff of only 63-65% & thrust in the 850gr range. 0906 would put it at 14a, 68% eff, 819gr thrust.... 60w of heat is a lot to ask a 57gr motor to shrug off. I have tours motor & will be running a 1050 on it, I'll be mindful of throttle management for sure, just wish they would tell the truth rather than making us dig for it like this.....
This engine is a possible way to powered the Nieuport XI Balsa 900mm (ARF), Turnigy 1300mAh 3S 25C Lipo Pack, Turnigy dlux 20A SBEC Brushless Speed Controller. Is this a good set? What's the best propeller? I'm experient at glows planes, but this is my first EP...
Can anyone advise what all the pieces are in the kit and why the shaft is poking out the wrong side. There is no shaft to bolt the prop onto. Yet there is a shaft sticking out the other end.What the deal?
It is frustrating all the engineering required to make the propsaver fit. I do not own a dremel and cannot easily fabricate a locking mechanism for the shaft to stop it pulling through the motor. Would be nice if they included a shaft that we could swap with to actually fit the accessories sold with it! Also got the wrong X motor mount which was irritating. Only really annoying aspect of the motor but otherwise great!
i had the bearing in my Pheonix 2000 glider motor fail and had one of these for another project fitted and tested with 10x6 folding prop and 3sx1800 lipo (model clamped) and full throttle applied amp reading 18.5A for 2 minuets and motor got hot but i think will be ok when airborne as load will be reduced any comments
I had this motor on an Airfoilz Extra 260 Full-Fuse plane. I was running a 10x4.6 prop, and the motor handled it just fine. I was also using a 30 amp esc and 3s 25-50c nano tech lipo. I did purchase another motor as I think I need more thrust.
you might be thinking of programming the speed control, your timing mode is how fast each phase fires, SPEEDING UP YOUR TIMING WILL NOT SPEED UP YOUR MOTOR!!! i dont think i can stress that enough set it at standard (around the middle or medium, or else it will fry your ESC
Sorry, I was thinking of the 15amp one... I have not used this one... however, I've used the 15amp one and the 23amp ones on 4cell and 6x5.5 props, so I'll assume this one would be ok too... prop for the same watts you would on 3cell...
Urgent!! Can anyone from Hobby King or another experienced customer with physical access to the 2213 motor tell me the linear distance between the far ends(and near end, if possible)of the holes used for mounting the motor. My entire mechanical design hangs from a thread for the lack of this information. Pls respond ASAP.
A good little motor BUT be warned when ordering the prop adaptor, shaft size measured at 3.15 mm, NOT 3.175 mm as advertised.
No comments. Reply..
7 thumbs up!
The only inconvience with this motor is that you have to solder the connecters on it. Also the wires exiting the motor are not color coded. Other than that this is one awsome motor especially considering is less than $20. I am very pleased with mine.
1 comment. Reply..
6 thumbs up!
This engine is a possible way to powered the ParkMaster 3D Multiplex (may be the 2213/22 924kv is better?)
3S zippy 1200 mAh 10x4.7 APC SF 17.80 A 11.12 v 198 W 7410 t/mn 1009 g efficiency 68 pcnt
Trs bon moteur idal pour un Parkmaster de Multiplex avec une hlice de 11X5.5. 4 stars seulement car l'axe est trs fragile et casse facilement (diammtre 3.17mm avec un paulement pour le circlips)prvoir une bague en sortie moteur
No comments. Reply..
5 thumbs up!
Motor jsem zkouel s 3l.LiPol 1300mAh 25/30C a vrtule AE 9/5"pluskuel 30mm.Regultor Himodel 25A.Proud na przdno 1,5A a zaten 16,5A!!!Teplota po 30s chodu na pln plyn byla 70C!!! Nepetovat nad 15A! Boban