Have bought one recently. PLEASE ...Anybody know the Max Amps it can do ?
I have done basic bench test with 3S and on a 6x4 got up to 14Amps. Isn't this too much for this motor ? since the specs above show Max amps=7A Would love to know from one of you experts TIA BTW how can you direct questions to an Expert??
I am thinking of getting 4 of these to put on a micro quad with a set of 3x3.5 props
my craft when fully laden will weigh in at about 40g-60g
will these motors get this thing off the ground or do I need to find something with a little more punch?
Sorry that I have to share this bad information with You....
Bought some of these 1806N-2100kv motors approximately ½* a year ago and they worked fine in my tricopter.
The last month i got 8 more motors divided in 3 shipments, but at least half of these is clicking when turning the shaft fast with my fingers. When I took the bad motors apart i could clearly see with my bare eyes that the ballbearings has maybe 0,3mm backlash/play when I wrickle the shaft. When running with ESC the bad motors make a terrible noise and will not last for long. And in multirotors they are useless, because their vibrations will disturb the gyro's on the controller-board. Now i try to get new ballbearings from e b a y, but i do not know if they will fit nicely and if they are any better !? No quality-control at these for sure :-(
Hi there i am having bit ot troubles.
I ordered a while ago both versions of this motor(the 2100 and the 2500 KV) and so i am having now some trouble finding out wich motor is the 2100 KV and wich the 2500 KV..?
I measured both and found out that if i measure the inner diameter of the mount one has 8mm and the other 8,5mm!
So could someone please help me and say me wich motor is the one with the 8mm and wich motor is the one with 8,5 mm??
Hi there V, if your talking about the micro cessna 182 that sold here on Hk than yeah this motor is fine and good for it. as I have the same problem like you did a whie back and crash mine nose down and I have tried this motor on the that little cessna and its work very well.
Does anyone know if it's possible to reverse the shaft on this and use it as a front-mount motor? I have received mine and suspect not, from looking at it, but not having reversed a motor before I'm nto sure.
This is one of the best motors in this size range, can take a bashing and no broken wires to contend with. Easy to repair if bent, unlike most, and a breeze to rewind is you need to go to a bigger prop. I recommend it to all my FBs and they love me for it.
21 thumbs up!
You´ll get a really fine motor, but the weigt with mount is 23gramm. without moint its 21gramm. Testet it with a 500mah 7,4V 15C Lipo an a GWS 7x3,5 = 5,5A on 10.300rpm. This will make an ETA of 77pcnt, like an AXI motor! - Sie erhalten einen echt guten Motor, aber das Gewicht inkl. Halter ist 23gramm, ohne Halter 21 gramm. Test: 500mah 7,4V 15C mit einer GWS 7x3,5 = 5,5A bei 10.300rpm. Das ergibt einen Wirkungsgrad von 77pcnt, das ist AXI-Klasse!
No comments. Reply..
11 thumbs up!
Im using it in Depron F-22 Raptor (160g)with pusherprop setup. With 5-5 prop and 2S800 draws about 10A and flies very well. Get around 13-14 minutes of flying. Tried it with 3S1000 for fun, and it really got the plane flying. Vertical handlaunch at half throttle. Gets a little warm, draws about 17 Amps. Really nice motor! Im going to get a couple more for a thrust vectoring project.
3 comments. Reply..
10 thumbs up!
I'm running it on a 190 gm (6.7 oz) biplane with a 2S800 LiPo and a GWS 6050 prop. Draws about 6A WOT, maybe 230g/8 oz thrust - the plane has unlimited vertical. With the prop adapter/spinner and connectors, mine weighs 27g. This has replaced the geared Feigao as my favorite small motor.