USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
how to wire the motor to the esc .. HK10A esc .. which wire goes where .. the motor has a black red and yellow and the esc has a red black and blue .. help thanks
If you mean H-KING 10A Fixed Wing Brushless Speed Controller by HK10A than it does not matter, for you can reverse the ESC with: H-King Air ESC Programming Card
Otherwise: switch the outer two pairs of the wires (keep the middle one connected) and the motor runs the other way around.
from experience, this is a 1600kv motor therefore would suggest a 7inch to 8inch prop. a 2cell 850mah batt with a 10A esc. im using a Gws EP-7060 prop, 2S 610mah batt with 10ESC on my 180grams parkflyer. it flys well and can go vertical
Me podrian explicar las siglas o datos que aparecen junto a los motores. tama?e los motores la potencia, ya que no entiendo. hasta a hora empiezo con este apacionante hobbie Gracias.
Very difficult if not impossible to remove prop saver, as it's an integral part of the bell / rotor.
Customer Reviews
Overall Rating
Paolo
likes
Value
UNRATED
Quality
UNRATED
20 thumbs up!
Value for money exceptional use 2 cells 300 mAh , flight for 7 minutes ( 3 in torque) model is heavy 138 gr.propeller GWS 8X4,3 perfectly support if replacing the two screws with 2 longer. The engine is not warm and very progressive using a speed controller A TURNIGY Plush 6A (very good) the manufacturer to improve it should use silicon wires:
No comments. Reply..
Overall Rating
Len Reinhart
likes
Value
UNRATED
Quality
UNRATED
13 thumbs up!
Cute motor in an unusual size. I need to find an adapter to try some bigger props, but with a GWS7035 which fits on it as is:
10600 rpm, 5 amps, 10.3 volts, thrust 254g
1 comment. Reply..
Overall Rating
Henris Emmanuel
likes
Value
UNRATED
Quality
UNRATED
9 thumbs up!
On 2S 460mah, turns a GWS 8/4.3 at 5700 t and draws 5.4A. Very good for the price. The reason for 4 stars is the prop adapter diameter 0.5 mm too small for the isnner GWS diameter ans sometimes the propeler wobbles. REmains a real bargain. Il will try some others of this range!
No comments. Reply..
Overall Rating
Andy23
256 likes
Value
UNRATED
Quality
UNRATED
9 thumbs up!
Motor is a turnigy. The weight is 17,9 gr. Including wires. The rpm (KV) without propeller is 1580. Measurements: (with Turnigy 6A ESC(high timing) and Eagle Tree Logger) GWS8043: 7,02V – 5,07 – 5896rpm – 263gr. Thrust – ETA 51pcnt (efficiency) 6,80V – 4,57A – 5605rpm – 238gr. Thrust - ETA 51pcnt The fitting for the prop is wrong for GWS 6xxx or higher, only the 5xxx and lower will fit. Glue a plastic nut into the big props and drill it up to 4
No comments. Reply..
Overall Rating
Tom Norin
likes
Value
UNRATED
Quality
UNRATED
6 thumbs up!
This is one terrific little motor!
A couple details, though. Mine didn't look the same. Orange body and shiny silver sides. Actually looks better. Buy some 1/2" x 2mm screws right now. The ones that came with the motor are too short.
Here are my initial test readings: GWIS EP6030 prop 3s 800mAh 15C Lipoly 43.1Watts on 10.8Volts 3.9 amps Thrust = 9.1oz
Motor barely warm. Runs smooth. Sweet. Can obviously take - and give - much more.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg&width=48)
