HGD digital 202 Carbon Gear BB -9.1g / .11s / 1.5kg

Total of 8 discussions.

rcmark

48 points - 3/28/2013

I bought 2 one worked I will not buy any more!!

symowallo

187 points - 11/16/2010

Where can I get the gear sets from? I don't want to buy this if you can't supply gear sets.

Maurice

5 points

****

icsss

9 points - 11/9/2010

I just bought 4 of this for my hk450 tail and cyclic. Does it work with hk401 gyro in HH AVCS? How many flights do you have with this servo?

icsss

9 points

Well they work very good and they are reliable, too bad no stock is available from some time..

akheli

6 points - 10/6/2010

When will this show up in stock? Comment says end of sept which is past.

CARLOS

59 points - 1/31/2010

Does this servo operate in the range of 4.8V to 6V?

aspim

14 points

Yes. It can operate in this range

JaRa5xxx

205 points

It may work, but the manufactory site inolabservo****/products_servo.html does not state any 6V specs for this one. There are 6V specs for some other HDG servos, so I wouldn't risk running this one at higher voltage for a prolonged time.

chartphred

40 points -

Would these fit a Blade 400 in the position behind the main rotor where the two servo's fit?

JAEGA

18 points

yes they will fit the blade 400. i run these servos on my beam 450 . very quick servos.

Achsenknecht

117 points -

Hi! Any news about a new ETA on HG-Servos?

Best regards
Joey

tekelito

39 points -

Hi !I need replacement gear set for this servo (HGD Digital 202 carbon gear)How can I do ?J-P

herbiehoss

117 points

HeliDirect****

Customer Reviews

Overall Rating		JUERGEN HEILIG likes
Value	UNRATED
Quality	UNRATED

51 thumbs up!

I ordered 4 servos as an initial buy to check performance and tolerances between servos. Quite often I need to try 4-5 servos in order to get two servos with identical performance for elevons or V-tails - not with the HGD 202 (production tolerances must be pretty tight).

The weight was spot on at 9.1g and although I could only achieve approx. 1.2kg@4.8V, the current consumption of only 440mA at this load is amazing for such a small servo. An idle consumption of 10mA is very good for a digital servo. Holding power and centering is excellent.

No comments. Reply..

Overall Rating		srrowell 68 likes
Value	UNRATED
Quality	UNRATED

33 thumbs up!

powerful, smooth, accurate centering servo. used on the cyclic in a 450 T-Rex clone heli, worked very well. I gave it three stars because there are no gears avalable and Hobby King customer support was absolutly NO HELP! Thies servos are too expensive to be disposable. Except for the complete lack of support this servo would rate five stars plus.

4 comments. Reply..

Overall Rating		Alvaro Fernandez likes
Value	UNRATED
Quality	UNRATED

11 thumbs up!

Excellent working on my T-REX450's tail rotor together with GY-401. Makes it cross the air like an arrow and define the curves perfectly. The only but is the thin wires its mounted on. Anybody knows where to get spare gear sets?

1 comment. Reply..

Overall Rating		Andre Gall likes
Value	UNRATED
Quality	UNRATED

8 thumbs up!

I have 4 of these little servos in my X-Rock. I like them very much because they are very fast an strong and hold their position very well. There are only few drawbacks: the cables are very thin and one of those 4 servos needs to be plugged in and out of the receiver a couple of times before it starts working. Otherwise it won't move at all. The servo arms are also a bit thin and flexible for my taste. I paid 16 USD for them back then and for that price I'd buy them again!

No comments. Reply..

Overall Rating		Chris Clark likes
Value	UNRATED
Quality	UNRATED

7 thumbs up!

Truly excellent performance. Great speed but most importantly they centre perfectly. Transformed the behaviour of my NMP Reflex. Got some more on order!

No comments. Reply..

.....click here to see all reviews