Spare Shaft for 24gram HXM2730 Motor

Item found in the following categories;
> Electric Motors > Motor Parts

RATED:


	Spare Shaft for 24gram HXM2730 Motor

Spare Shaft for 24gram HXM2730 Motor

3mm diameter
Short shaft, for use with prop saver or adapter. No thread.

PRODUCT ID: HXM2730-Shaft

-13

$2.00

Further discounts available for registered & logged-in customers.

STOCK ARRIVAL ALERT

Enter your email address to get an email the second new stock arrives.
Estimated factory delivery date;

Stock updated frequently.
No ETA,goods will arrive every 15-20 days

Customer rated

548
crowns

Total of 22 discussions.

Harry

12 points - 5/24/2013

Hi everyone...need a replacement shaft for my 2812 - 1534kv motor...will this shaft fit nicely?

MAIRTON

9 points - 1/25/2013

can anyone tell me the size of this shaft?

Dongskie

234 points

3mm diameter (thick) and 42mm Length (long)

Andiww

24 points - 11/17/2012

Will it be available???

Dongskie

234 points

It's available now 2/27/13

felipe

2 points - 11/14/2012

how long is this shaft?

Dongskie

234 points

42mm Long

Andiww

24 points - 11/4/2012

Will it be available again?

Dongskie

234 points

Yes, its available now 2/27/13

JEEP64

1 points - 9/29/2012

Bonjour, Je suis à* la recherche d'axes de ce type( 3mm X 47mm) que'elle longueur fait-il ?

chiliidawg

48 points

42.1mm long

frank

12 points - 8/11/2012

I have the L2210-1400kv motor. Can i replace its shaft with this one?

PILOTO-SP

65 points

You can load, will be shorter than the original.

frank

12 points - 8/11/2012

Is it possible to change the shaft to the 3mm shaft with no thread?

frank

12 points

Ignore my last message. I meant say has anyone try putting this shaft into a Turnigy 1400kv motor?

tjek0305

8 points - 8/6/2012

I need some C-clips for this shaft. Can i buy it at HK?

EDWARD

71 points

If you replace old shaft with this one, why not save the old C clips? Been using bell type motors for years, both pusher and puller, bell never comes off during flight. In case C clip might not fit perfect to the new shaft, use a file to rim the inner part of C clip to fit. Happy flying!

PILOTO-SP

65 points

You can find the clip c in a hardware store or screws near his home

Manuel

1 points - 4/12/2012

Can this work on an engine Turnigy 2730 Brushless Motor 1300kv?

RexSe7en

14 points

Yes it should work without a hitch. This shaft is notorious for working with pretty much any motor this size with a 3mm shaft.

BEST ANSWER CREDIT AWARDED

Manuel

1 points - 4/12/2012

Can this work on an engine Turnigy 2730 Brushless Motor 1300kv.

RexSe7en

14 points

Yes, this spare shaft is good for pretty much any motor with a 3mm.

scotttankersley

5 points - 12/30/2011

will this fit turnigy 2205... shaft diameter in question, its a 3mm shaft but i think the 2205 shaft is a hair larger, not sure?

Glider Squirrel

9 points

This shaft won't be a perfect fit, and I wouldn't recommend it. There is, though, 2205 motor accessory pack (ID: TR2205) that includes a spare shaft that is guaranteed to fit it snug. And the accessory pack is only $3.63 including other useful parts, you can't go wrong!

Hamdhan

155 points - 11/16/2011

How does one fix this on the motor?

e_lm_70

487 points

Just unscrew the little 2mm holders, and the motor shaft can be easily replaced

EDWARD

71 points

You will need C-ring and a washer, both designated for 3mm shaft, to fit one end of the shaft (you can easily see a groove on one end of it), unless you are running a pusher setup. Then remove the old shaft from the motor by unscrew those set screws, some tools might be needed. Then put the unthreaded end of this shaft into the ball bearing on the stator. Then align the set screw on the rotor with the flat spot on the shaft (This is not always feasible when I worked different motors* as long as

Derio

11 points - 11/11/2011

Hi Gys, Some body knows if can I fix the motor "NTM Prop Drive Series 28-26A 1200kv" with this Shaft? Thanks a lot. Regards, Derio.

e_lm_70

487 points

Yes, you can. The HXM shaft is 42mm long and 3mm wide, exactly like the NTM 28-26 motor

Derio

11 points

My friend e_lm_70, Ok, Thans o lot for your reply back. Best regard, Derio.

jonasmuex

55 points - 8/23/2011

Can this fit the Towerpro 2408-21?

cocopl

52 points

No it's bad shaft for this motor . You need orginal shaft .

Roy_T

134 points

Yes you can. However, you'll need a prop saver for the prop as you only have about 20mm of shaft allowance.

BEST ANSWER CREDIT AWARDED

jonasmuex

55 points

so which is it???

PILOTO-SP

65 points - 5/31/2011

This shaft is for the motor EMAX 2822?

cocopl

52 points

Yes , its good shaft for 2822 motors . Its 5mm shorter than orginal. I use it in this emax.

BEST ANSWER CREDIT AWARDED

twostroke-CRO

36 points - 10/23/2009

TPC>4-1-9x6 - TowerPro BM2409-18T / 25A BEC / 9x6

wich shaft i have to order for that motor

THANKS

Waltudes

14 points

you have to buy one shaft with 3mm of diameter. But HK don't sell then.

Nadim

87 points - 10/19/2009

Any news on when your going to re-stock this item?

Thanks
Nadim

Raymond

13 points - 9/7/2009

I have broken shafts on two of my three motors (on a NutBall). I NEED these sharfts bad. Please restock soon.

Fl_red61

111 points - 8/11/2009

Please give us an ETA on this item. It's been out of stock for too long!

Håvard

120 points - 6/18/2009

Are you guys getting this in again soon? I really need them x)

Josemi

23 points -

Is this shaft useful for the towerPro BM2409 18T? thanks

twostroke-CRO

36 points

i have sam qeustion like Jose.can somebody answer please

THANKS

Customer Reviews

Overall Rating		Kostas Brouzas likes
Value	UNRATED
Quality	UNRATED

10 thumbs up!

Nice and cheap product.

Actually can be fitted to many motors using 3mm shaft like AX, towerpro, FC etc

Its 42mm long. At one side can be fitted a C clip on the other has two flat points for the prop savers and motors bell screw.

For perfect fit motors length should be 30mm

3 comments. Reply..

Overall Rating		Afanddy Bin Hushni likes
Value	UNRATED
Quality	UNRATED

4 thumbs up!

I've bought this 3mm sharf not for HXM2730-1300 motor but for my Emax 823kv 3mm sharf and it's fit well! Till now still no sign of bent or else. good and cheap!

1 comment. Reply..

Overall Rating		Malcolm Parfitt likes
Value	UNRATED
Quality	UNRATED

2 thumbs up!

I bought 5 of these shafts. Used 1 in a Tower Pro motor and 1 in an Emax motor. They fit with slight mods but work great. 5 out of 5. Its hard to get replacement shafts for some brands.
Mal

1 comment. Reply..

Overall Rating		Michael Latif likes
Value	UNRATED
Quality	UNRATED

1 thumbs up!

I have used these shafts as replacements on AX1806N motors, they fit perfectly, have the exact groves in the correct places. Never had one fail on me, great replacement .

Would recommend purchasing half a dozen for those beginning to learn how to fly :-).

No comments. Reply..

Overall Rating		DOCA-SP 2075 likes
Value	UNRATED
Quality	UNRATED

1 thumbs up!

Barato e serve na maioria dos motores.
J usei nos EMAX 2805/2812/2822

No comments. Reply..

.....click here to see all reviews

Spare Shaft for 24gram HXM2730 Motor

Spare Shaft for 24gram HXM2730 Motor3mm diameterShort shaft, for use with prop saver or adapter. No thread. PRODUCT ID: HXM2730-Shaft

Spare Shaft for 24gram HXM2730 Motor

3mm diameter
Short shaft, for use with prop saver or adapter. No thread.

PRODUCT ID: HXM2730-Shaft