USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
The Hextronik 5010 servo wont break any records, it wont astound you with its amazing torque or scare your friends with its ninja-like high speed action, but it is a solid, reliable plastic gear servo thats economical and great for those that are not too serious about specification.
tou querendo comprar 5 servos desse para usar em um recptor jr com uma bateria de 1100 mah e 6,6 volts alguem sabe dizer se tem algum problema essa montagem?
Nao recomendo esse servo .. queimei 3.. simplesmte depois de 5 minutos .. cheirava e queimava... realmente tive q queimar 3 servos pra descobrir q ele nao presta.. troquei de servo e pronto .. cabo o problema... nao comprem esse !
indeed, if this servo is failing it is failing already when you unpack it. I've already ordered more than 30 of them and had 1 doa... all the others are (until now) still functioning fine
Maybe what he means is that this servo´*s torque is not enough for big planes, like gas planes and glow planes for 3d. But it would be a great servo for glow plan if your plane is not acrobatic or "radical /3d" usage.
Mentor is not correct. These servos produce 90oz/in torque at 4.8v and more at 6v. That is more than suitable for a 20-50cc gasser. As a matter of fact I've been flying three 30cc and 50cc gassers with these servos without problems for the past two years.
the only plane I didn't use them is a 62cc tow-plane because I was more or less affraid that they will not be "good enough" for the flaps that go 90°* all the way. All other planes going from 10cc up to 50cc are doing fine with this servos
it depends of the size and placement of your rudder, but for sure it will be enough! i ve put on mine boat after propeller, 1000w brushless,and that seem to work too much(rudder dimensions: 30 *55 mm)! a few degrees in right or left and the boat want to run on canopy!
will this servo be a good choice for a topflight gold spitfire i am building? wingspan is 63". the engine will be osmax 91 4c and weigh about 11 lbs.build instructions calls for standard servos.
Este Servo lo he instalado en los alerones de una Piper Cub de 84" de envergadura, exelente respuesta al baston de mando del Radio Futaba 7C. este servo por su precio supera al Futaba S30004.
Purchased 6,tested all six. Installed 4 in a new plane, flew today. I have used all types of servos for 40 years. It really does not get better than this. Strong, fast, quiet. I still cannot believe the price. I will buy more and use them in all my planes.
6 comments. Reply..
Overall Rating
kevin wall
likes
Value
UNRATED
Quality
UNRATED
66 thumbs up!
I was amazed at how well these servos perform, thought they might be a bit jittery around the centre but they are not.have 4 of these in my .76 engined extra and they are terrific,can only fault one thing and that is they may be a bit noisey but hey, you cant hear them in the air lol would recomend, i will be ordering more and putting these in other planes i have.
2 comments. Reply..
Overall Rating
Customer
52 likes
Value
UNRATED
Quality
UNRATED
33 thumbs up!
quiet and smooth running but will to a large lever
I am quite disappointed with operation quality of this servo. It is cheap, light but extremely noisy and tugging operation. I try to lubricate cogwheels with teflon vaseline with poor effect. I bought 6 and test 2 pieces with the same result.
5 comments. Reply..
Overall Rating
Michael Deasy
likes
Value
UNRATED
Quality
UNRATED
27 thumbs up!
I read the HX-5010 servo reviews and observed the advertised specification of 4us dead band. I ordered 10 servos. When I received the servos, I tested the performance on my Hitec HFP-10 servo tester. The dead band for all 10 servos measured 8-9us compared with only 5 us for the standard low-cost Hitec HS-422. The servo might be ok for motor control or rudder.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
