TowerPro Alloy Stick Mount for 24** Motors

Total of 4 discussions.

leonardo

53 points - 4/11/2012

can i use this mount for noot bell type motor?

SumthinsFishy

72 points

Not directly. You would have to make an adapter.

CAN

400 points

It is especially for bell type , u can use another mount for not bell type motor , this cant be sstronger than them if u use adaptor or another material.

BEST ANSWER CREDIT AWARDED

mohd

12 points - 2/24/2012

ye mast rhega fitting k liye

johnkim100530

255 points - 7/8/2011

Does this fit to 8mm or 11mm motor shaft?

kencam1

5 points

This fits 8mm

Andrew

5 points

8mm only!

srt8madness

46 points

Just the 8mm shaft, like on the Hextronix 24gram motors

webber

1614 points -

I use this tiny thing in micro COX warbirds models with a 18-11-2000 outrunner and it performs great.

fluchtagesiste

4 points

Yeah its great its quite strong too :D

Customer Reviews

Overall Rating		Kostas Brouzas likes
Value	UNRATED
Quality	UNRATED

25 thumbs up!

Great motor mount,

BECAREFUL it only fits towerpro 2410**
and 2408**

NOT 2409** motors

You can also use it with hexTronik 24gram Brushless Outrunner

All above motors fit the mounts 8mm hole

It wont also fit AX 2306N 1300kv brushless Micro Motor which mount hole diameter is 9mm

Towerpro 2409** motor need 10mm diameter mount

Nice flights in perfect Greek blue sky!

3 comments. Reply..

Overall Rating		Robert Chatenever likes
Value	UNRATED
Quality	UNRATED

11 thumbs up!

The inside diameter of the mount is approx 0.312". It will accept a 2408-21 motor, but it is too small to accept a 2409-18, which has an outside diameter of approx 0.395". The length of the mount (in the direction of the stick mount) is only 0.400". When mounted on the stick, this dimension is really too short to provide stable alignment with the stick because the alloy mount can "wiggle" on the stick.

2 comments. Reply..

Overall Rating		Kostas Brouzas likes
Value	UNRATED
Quality	UNRATED

4 thumbs up!

1 comment. Reply..

Overall Rating		Mark Fisher likes
Value	UNRATED
Quality	UNRATED

3 thumbs up!

This mount worked great on my old Slow Stick with the aluminium tube fuselage, but is too tight for the new Slow Stick with the fibreglass fuselage.

No comments. Reply..

Overall Rating		Claire Gray likes
Value	UNRATED
Quality	UNRATED

2 thumbs up!

Although some aspects of this item could be improved, it does what it is intended to do and is pretty lightweight.

I've used several of these aned I had no problems with the fit as I cut a stick out of hardwood to match.

When I did have one that was a loose fit, instead of using screws I just used a small hot glue gun to heat the alloy up then injected hot glue in through the side holes, it was very secure and no chance of the wood splitting.

However, the clamp could be more secure as the cooling fins bend if you over-tighten them and the motor will escape if they aren't quite tight enough.

I'm still giving it 5 stars as without it mounting this type of motor to sticks would be very difficult.

:)

No comments. Reply..

.....click here to see all reviews

TowerPro Alloy Stick Mount for 24** Motors

This little low priced device will save you as much weight as it will dollars. It fits directly onto the back of all towerpro BM 24 motors and can be fixed to most stick mount planes. The stick mount section is 10x10mm PRODUCT ID: TPHEATMOUNT

This little low priced device will save you as much weight as it will dollars.

It fits directly onto the back of all towerpro BM 24 motors and can be fixed to most stick mount planes.

The stick mount section is 10x10mm

PRODUCT ID: TPHEATMOUNT