USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> FPV & Telemetry > FPV > Video Tx/Rx > 1.2GHz

  RATED:

1.2GHz 100mW Video Transmitter and Receiver Combo

1.2GHz 100mW Video Transmitter and Receiver Combo
1.2GHz 100mW Video Transmitter and Receiver Combo

This is the perfect size for Micros and specialty application where you need the better penetrating power and range of the 1.2GHz band but size is limited. The set is matched and tuned to work flawlessly together and has 4 channel selectivity. Their ability to work as low as 3.3v makes this perfect for single cell applications. Time to fashion up some spy gear or micro FPV flying action!! 

Video Transmitter Specs:
Voltage: +3.3~5.0V
Current Consumption: 85mA , Max
Operating Temperature: -10~+70 ºC
Transmitting frequency range: 1280 ~ 1360MHz
Voltage Standing Wave Ratio: 2:1
Modulation system: FM/PLL
ANT output impedance: 50Ω, Typ
LO Frequency stabilization: ±100kHz
LO Frequency Precision: ±200kHz
LO Control: PLL
Transmitter Power: 17dBm (100mw)
Video input impedance: 75Ω, Typ
Video Polarity: NEGATIVE
Video Frequency Response: ±5 dB, Max. 50Hz ~ 6MHz
Channels:  1280, 1300, 1320, 1340Ghz
Size: 18 x 8 x 3.5mm
Weight: 2 grams (with connector)

Receiver Specs:
Voltage: +3.3~5.0V
Current Consumption: 120mA , Max
Operating Temperature: -10~+70 ºC
Receiving frequency range: 1280 ~ 1340MHz
Voltage Standing Wave Ratio: 2:1
Demodulation system: FM/PLL
ANT Input impedance: 50Ω, Typ.
LO Frequency stabilization: ±100kHz
LO Frequency Precision: ±200kHz
LO Control: PLL
Input LO Leak: -55dBm
Receiving Sensitivity: -85dBm
Input Level Range: -85 dBm ~+5 dBm
Video Output impedance: 75Ω, Typ.
Video Output Level: 1Vp-p, Typ.
Video Polarity: Negative
Video Frequency Response: ±5 dB, Max. 50Hz ~ 6MHz
Differential Gain: ±5 %, Max
Differential Phase: ±5 Deg., Max
Channels:  1280, 1300, 1320, 1340
Size: 26.8 x 23.2 x 2.8mm


PRODUCT ID: 381000151


Weight: 18g Quantity: 
stock
BK
Price$21.28


acc.
  • Micro Camera with LED Lamp 420TVL

    Combo Price: $19.44   BACKORDER

  • 1/3-inch SONY CCD Video Camera (NTSC)

    Combo Price: $16.95   IN STOCK



Further discounts available for registered & logged-in customers.
STOCK ARRIVAL ALERT

Enter your email address to get an email the second new stock arrives.
Estimated factory delivery date;
 Customer rated
38
crowns
  
 
Total of 121 discussions.
gamekeeper  23 points - 4/2/2014
 
How much longer before new stock arrives ?
Didenko  22 points - 3/31/2014
 
pls some one post close picture this RX TX looks lke it back order forever.
Dave  5 points - 3/17/2014
 
how long is this going to be on backorder?! I really want one!
Voodou  47 points - 2/16/2014
 
Does it work with lawmate receiver? I know that they have a common frequency but is it compatible?
 Waterbound 25 points
Yes, I have mine set to 1280 and I am picking it up on my lawmate and my do-cav RX with no issues.
BEST ANSWER CREDIT AWARDED
 Voodou 47 points
Thanks for answer. How far can you go?
 Waterbound 25 points
I'm currently using in a brushless tc3 car and able to get more than 80' away and haven't tried further since my 2.4g interferes at that range. In my micro quad I was able to fly in los but at least 115' with no issues.
RC2211  297 points - 2/15/2014
 
Sorry but is this guy PAL or NTSC video?
 Waterbound 25 points
Pal or NTSC is defined by your camera not vtx type.
BEST ANSWER CREDIT AWARDED
 RC2211 297 points
Thanks I'm very new. What I meant is can it says support both?
 Waterbound 25 points
Absolutely, transmitter transmits vide signal and does not care what type it is, that is dependent on camera used. If you use PAL you won't be able to see on us standard tv, vise versa for NTSC.
Customer Reviews
Overall Rating
RCBUG80
135 likes
Value
Quality
Like it?
Great little kit if your after a very lightweight fpv setup. Works well with the micro camera with led in the recommended accessories.


No comments. Reply..

Overall Rating
EngineerX
31 likes
Value
Quality
Like it?
Operating frequency is 1340 MHz,(I uploaded picture- checked with frequency analyzer) unless there's a way to change channels with the solder pads, but I've read you might fry it if you try to change channels with pads. It takes a few connect/disconnect cycles for the Rx to get and send the video signal to a screen. "Channels: 1280, 1300, 1320, 1340Ghz" description is misleading. Perhaps someone can figure out how to change channels on Tx. I tried the Rx with a 1280MHz Tx and it would tune to 1280MHz, seems it defaults to 1340MHz, pitty that's just outside the legal amateur frequency in the US and even Int'l: 1300-1350 AERONAUTICAL RADIONAVIGATION 5.337 Radiolocation G2 5.337 The use of the bands 1300-1350 MHz, 2700-2900 MHz and 9000-9200 MHz by the aeronautical radionavigation service is restricted to ground-based radars and to associated airborne transponders which transmit only on frequencies in these bands and only when actuated by radars operating in the same band. 5.337A The use of the band 1300-1350 MHz by earth stations in the radionavigation-satellite service and by stations in the radiolocation service shall not cause harmful interference to, nor constrain the operation and development of, the aeronautical-radionavigation service I tried running at same time with a 1280MHz Tx and it was possible to receive both signals with little interference at close range


4 comments. Reply..

Overall Rating
FR4-Pilot
12 likes
Value
Quality
Like it?
Neat little set, if you can run 1340MHz in your area. HobbyKing needs to provide instructions on how to change channels, since they're listed in the product specs for the vTx and vRx. Otherwise remove them and advertise as a single channel set - 1340.


1 comment. Reply..

Overall Rating
NiVeL44
49 likes
Value
Quality
Like it?
Soldering quality sucks badly on RX. It came with 2 loose wires (video and GND). REALLY hard to solder them back.


No comments. Reply..

Overall Rating
redadeath
35 likes
Value
Quality
Like it?
very very good i checked it all over my house with alot of walls and it is working bestter than boscam 5.8 200 mw the picture seems to be stable and powerful just be carefull with wiring and polarity


2 comments. Reply..

.....click here to see all reviews
Aff. Link