The software for the 9XR first began development 6 years ago. Since then it has been tweaked, tuned, changed, updated and revamped by members of the R/C community into a powerful - yet easy to use interface. Our engineers designed the physical product around the R/C communities software changes and input. The culmination of all these is the Turnigy 9XR!
For many users this will be the perfect 9 channel radio straight out of the box, but there are many tinkerers out there who love modifying and pushing the boundaries of what is possible from their radio.We have factory fitted the 9XR with an AVR ISP header to simplify the development of custom software, we have launched turnigy9xr.com as the epicentre for software developers and additional community support for all 9XR users......With the 9XR we encourage it!
The 9XR is supplied preloaded with top quality software which is full of features and yet remains easy to use. Our aim was to develop a radio for you, the hobbyist,with an extensive list of standard features usually expected from a radio system 3 times the price. Our Turnigy 9XR is everything you imagined and more!
9XR Standard Features: • 8 Channel PPM/9 Channel PCM • Full Ball Bearing gimbals • Adjustable Stick Length • Digital Trims on all Primary Axis • 16 Model Memory • Assignable Switches • Freely Assignable Channel Mixes • Graphical Dual Rate and Exponential • Sub Trim and Travel Adjust • Flaps and Differential • Throttle Hold • Supports Heli/ Aero/ Glider Model Types • Programming Templates Based on Model Type • Supports M1, M2, M3, M4 stick modes • 128 x 64 backlit Liquid Crystal Display • Built in JR & Futaba Trainer Ports • PPM & PCM Output • JR Form Factor RF Modules (Orx Dsm2, Orx Open LRS 433Mhz etc) • Programmable Timers • Low Voltage Warning and Buzzer • Supports 3s Lipo (Required) • 9XR Firmware Pre-loaded • AVR ISP Interface • Internal 2.4GHz Antenna
Online support and user forums available at: www.turnigy9xr.com
Spec: Channnel: 8ch ppm/9ch pcm Display: 128*64LCD (Backlit) Support Type: Heli/Acro/Glid Model Memory: 16 Stick modes: 1, 2, 3, 4 Encoder type: ppm/pcm Module Interface: JR Compatible (See Related Items Below) Simulator Interface: Yes (JR & Futaba) Buzzer: Yes Battery Compartment: 112 x 44 x 27mm Weight (less battery & Rf Module): 723g
Required: Battery 3S Lipo RF Module
Included: Turnigy 9XR Transmitter (Mode 2 – Throttle on Left Stick) Quick Start guide
Note: This version is supplied without an RF Module, Please order the relevent RF module from the accessories list below.
Flysky modules are available on ebay for AU$25 delivered, so you can use your existing 9x RX's, that's what I did it's called...FS-TH9X-B-Module Antenna for 2.4G 9CH Radio System, works great no issues installing it worked straight away.
my 9XR arrived a few days ago and now i had a problem with it. When i switch it on it makes a continouis "peep". So i thought perhaps its the Firmware and flashed it to er9x. But there is the same Problem. The Receiver has a signal for the Elevator Trim which does not com from the Button. But where can it come from? Is there any Person who had the same Problem and could fix it? The Signal came from anywhere but where is the source?
Thanks for any Reply
P.S.: The Video i put on is another Person i found at Youtube who has the same Problem on rudder Trim
By changing the software you probably voided the warranty, BUT if you open the Tx case up you will probably find a dob of solder or something shorting out that trim, possibly a wire off?, you will have to open the unit up to check the trims wiring, good luck with it.
Trank for Reply. I tried this First but the Signal did Not Come froh the trim Button. My First thought was that the processor perhaps gives a wrong signal or that some contacts did Not fit. But froh where could such a signal Come?
To update the firmware on the 9XR i have a USBASP adapter that has a 10 pin out cable - if i use a 10 pin to 6 pin adapter, will the pin outs be right for the 9XR? Is there a diagram of the pinouts or will it be already in the right order?
I, along with someone else I know, received our 9XR today. The gimbals feel MUCH nicer, and it is a big improvement. It fits the product ID : ZIP25003S3C nicely. The balance connector should be farther down, because it puts a little stress on the wires. Haven't actually flew with it yet, as I am waiting on my DJT module.
30 comments. Reply..
Andr in Thailand
Wooww, T9xR is t arrived. Looks a little funny. Not really nice but I'll get used to it. I use the Nano Tech 3s 2500mA Lipo from the old T9x. But I had to extend the balancer. Soldering is announced. I use the Corona module with CR8D's receivers, has arrived today. This works very well. (Set a range of about 2 km have) The T9xR lies well in the hand, but it is not a sensation for the 6 years of development time. But it works, the software is good and I'm satisfied. For only $ 49 almost a gift. I was in the air now with my big Quad and must say, its no difference to the old T9xR, a little trimming and is like before. Only the new FW, i like it.
6 comments. Reply..
likes:- looks good , display is brighter than 9x , sticks have a better feel , takes a standard 3s lipo jst connector , which means pretty much any 2200mah 3s battery will fit.
Dislikes :- "star" selection button is poor . 12v charge socket goes direct to lipo jst connector , no ballancer so lipo will be damaged if you connect an industry standard tx charger to it. software isn't compatable with "companion 9x" so you can't connect it easily to a pc or load your existing models to the radio without wiping 9xr hex file.
5 comments. Reply..
Great radio. much better quality that the 9X. It definitely looks better in person compared to the pictures IMO. the gimbals feels good. switches feel really good. the whole ergonomics of the 9XR is OK, felt better. battery bay is quite big but the connector is not in an ideal place. Here is my review on youtube http://youtu.be/VH37smjFk94
2 comments. Reply..
Much nicer than the 9x. Nice bright screen. The switches seem to be easier to reach. Battery compartment is improved with the included piece of foam. Plastic handle feels more solid than the 9x's thin metal tube. Gimbals feel like they are higher quality. The power switch doesn't feel so cheap either. Once you put a battery in it the weight is not bad and it has a solid feel. Also like having both Futaba and JR trainer ports. The only thing I would change would be to remove the exclamation point after READY.