Please confirm your location:

USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Speed Controllers > All Speed Controllers
> Speed Controllers > Car ESC
> Cars & Parts > Speed Controllers
> Cars & Parts > TrackStar > Speed Controllers > ESC


Turnigy TrackStar 100A 1/10th Scale Sensored Brushless Car ESC

Turnigy TrackStar 100A 1/10th Scale Sensored Brushless Car ESC
Turnigy TrackStar 100A 1/10th Scale Sensored Brushless Car ESC

The Turnigy TrackStar 1/10th scale 100amp car ESC is the latest addition to Hobby Kings Sensored Car ESC range.

Using a Fast Silicon Labs MCU and high quality On-Semiconductor MOSFETs the TrackStar 100A ESC sets a new standard in high quality yet affordable car ESCs. With Intelligent MCU logic the TrackStar series ESCs allow extremely precise start up control and positioning feed back from the motor. This translates in to very smooth start up and acceleration.

Timing Indicator LED.
To conform with ROARs Sportsman Class racing rules and assist race organizers monitor driver compliance in non-timing modified race classes the TrackStar 1/10th ESC includes a timing mode indicator LED. At all times when the ESC is powered on and dynamic motor timing is set to a value greater than zero the white LED will illuminate indicating that the timing mode has been modified.

The Turnigy TrackStar 100A ESC also boasts a host of programing options not usually found in a 1/10th scale ESC at this price and can be programmed with ease via the Turnigy TrackStar programing card (sold separately) The Turnigy TrackStar 100A ESC also included 3 x 12AWG Motor wires and 2 x 12AWG power input wires.

Cont. Current: 100A
Burst Current: 200A
Car Size: 1/10th
Battery: 2-3 Cell Lipo
L-BEC: 5.0V / 2A Output
Motor Type: Sensored or Sensorless Brushless
Size: 40.5 x 37.5 x 24mm
Weight: 45g
Battery Plug: Required
On/Off Switch: Yes
Reverse: Yes
Thermal Overload Protection: Yes
Battery Terminals: 12AWG size
Motor Terminals: 12AWG size

Programming Options (Via Optional programming card)
Brake/Reverse type
Brake amount
Reverse amount
Punch Control
Drag Brake
Throttle Dead Band
Voltage Cut off
Motor Timing
NEW! Motor Reversing (v2.0 software)

PRODUCT ID: 9052000037

This is an archived page. This product is no longer available and has been replaced by a newer product.

Weight: 180g
International Warehouse
Price  $51.75

  • Turnigy TrackStar Turbo and Waterproof ESC Programming Box

    Combo Price: $9.77   BACKORDER

Further discounts available for registered & logged-in customers.

Enter your email address to get an email the second new stock arrives.
Estimated factory delivery date;
 Customer rated
Total of 44 discussions.
dominic  5 points - 10/8/2014
hello i have this brand news esc never use ..the problem is ... always green flash whit red flash and beep 1 time / second and i have no fan working and no receiver 12v. on ... anyone has a solution ?
 dominic 5 points
ok its working now , i just wanted to smash on the table ...and now work good ?????
Antonio  1 points - 5/29/2014
Hello I have this ESC, working correctly but with ESC off, plug/connect the positive wire to negative battery and struck a spark. Now not working but has power, servo works, fan, lights but not "beep" sound and throttle. The ESC is over or have solution? Thanks!
 Fartinmartin 5 points
It is dead
 dominic 5 points
when the motor is not connected right = no bip sound
Alec  6 points - 5/4/2014
The ordinary grey card, search "trackstar program card". It's the only result :)
craig  1 points - 4/30/2014
which program card do i need for this. i have tried the turnigy multi function and waterproof box but they dont work
 Denis 6 points
you need the trackstar flash card.. it's the only one capable of programing this esc..
Dylgriff  2 points - 3/18/2014
Which programmer do i need to reverse rotation of a sensored motor for a 4 gear mid motor buggy. There doesnt seem to be the option available on the recommended program card, Does the turbo program card work???
 rustyvr4 3 points
on your transmitter. you should have a switch to reverse the channel.
 Andy 38 points
No, that doesnt work. You have to use the TX programming method. I believe its option 8 or 9, but I have to check. You'll know when you're at the right one when it only has two options (clockwise and counter clockwise. If you just reverse tx channel, you'd just be driving in reverse, which would lack punch and top end.
Customer Reviews
Overall Rating
Like it?
right this esc bruns up the sensor,s in the motor when you plug in the sensor plug on 17.5t 1870kv trackstar motor and it work,s fine without the sensor so DO NOT USE SENSOR WITH TRACKSTAR 17.5T 1870KV AND TRACKSTAR 100AMP SENSORED ESC IF YOU NEED TO RUN SENSORED

No comments. Reply..

Overall Rating
Like it?
This is a great esc, small and light and very easy to program and will not over-heat my only flaw is if the bec was 6 volts instead of 5 volts but at the price it is a steal!

No comments. Reply..

Overall Rating
Like it?
awesome product had mine in my drifter with a 8.5t trackstar sensored, no hassles keeps up with my mates viper 4t and 80a esc all day long, just solder motor to the already attatched esc wires and lipo plug and off you go! very religable

No comments. Reply..

Overall Rating
Like it?
Was good in my SCT, got me into sensored for nice and cheap and it never, ever gets hot. Moved it across to my tourer with a 10.5t and it's really very average in that, it's not at all smooth - tends to 1 out of 4 runs into a straight get very bogged up mid range, and then suddenly starts to open up and give you power again, just extremely inconsistent and not at all smooth once you're pulling high amps through it, I guess. Overall a good set up for the $$$ though!

No comments. Reply.. here to see all reviews
Aff. Link