Please confirm your location:


USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Radios & Receivers > 2.4Ghz Futaba
> Radios & Receivers > OrangeRx Receivers, Radios & Flight Stabilization > OrangeRx Transmitter Modules

  RATED:

OrangeRX DSMX/DSM2 2.4GHz Transmitter Module (Futaba Compatible)

OrangeRX DSMX/DSM2 2.4GHz Transmitter Module (Futaba Compatible)
OrangeRX DSMX/DSM2 2.4GHz Transmitter Module (Futaba Compatible)

The OrangeRX DSMX/DSM2 2.4Ghz transmitter module offers a simple and convenient way to utilize your module-based Futaba compatible transmitter with DSMX/DSM2 receivers. Simply replace your stock module with this and you are ready to bind to any DSMX/DSM2 receiver. 


Features:
• 100% Futaba compatible (works with any Futaba compatible module-based transmitter)
• 4 operating modes: DSM2 1024/22ms, DSM2 2048/11ms, DSMX 22ms, DSMX 11ms
• Easy to access bind button
• Range check mode

Specs:
Compatibility: All Futaba 5 pin module-based transmitters
2.4Ghz protocol: DSMX/DSM2
Voltage input: 6~15VDC
Power: 100mW
Range: Full range system

Includes:
OrangeRX DSMX/DSM2 2.4Ghz transmitter module (Futaba compatible)
2.4Ghz antenna
RX bind plug

Module uses a unique Global ID for binding. In case of binding issues with other branded receivers press the "Change ID" button on module to change the Module ID to another unique value reserved for that module (5 ID's assigned to each module).

There are over 4 billion unique ID's assigned to OrangeRx modules.

NOTE:
1) Accepted by the MAAA in Australia, see the MAAA MOP58 for guidance
2) This is not a Spektrum module, nor is it a copy of a Spektrum module.
The Spektrum brand is a trademark of Horizon Hobbies USA.
3) Price of this moduler may fluctuate (up or down) due to cost of electronic components.
4) This is not an underground manufactured fake Spektrum module. OrangeRx quality is guaranteed.

Visit orangerx.com/">www.orangerx.com for news and updates on OrangeRx products.


PRODUCT ID: 9171000069

This product available from a warehouse near you!


Weight: 74g Quantity: 
United States Warehouse In Stock View Item
stock
10+
Price$29.99


acc.
  • OrangeRx R615 Spektrum/JR DSM2 Compatible 6Ch 2.4Ghz Receiver

    Combo Price: $5.95   BACKORDER

  • OrangeRX USB Firmware Update Kit for JR/Futaba Style Transmitter Module

    Combo Price: $7.11   IN STOCK

  • OrangeRx R620 Spektrum/JR DSM2 Compatible Full Range 6Ch 2.4Ghz Receiver w/Failsafe

    Combo Price: $12.91   IN STOCK

  • OrangeRx R710 Spektrum DSM2 Compatible 7Ch w/Failsafe

    Combo Price: $17.95   BACKORDER



Further discounts available for registered & logged-in customers.
 Customer rated
428
crowns
  
 
Total of 305 discussions.
Timothy  1 points - 7/27/2014
 
Will this model work with a T8FG so I can fly a Blade 130x?
William  1 points - 7/21/2014
 
Will this attachment work with a Futaba FP-T6NFK transmitter, (72 mz)?
 peckle 14 points
Unfortunately no. The Futaba FP-T6NFK does not use a module system for its transmittion so there is no way to plug this OrangeRX module in.
Gadgieboy  32 points - 7/14/2014
 
I'm looking for a futaba module that can fit into the back of my frsky taranis transmitter? The module needs to work with futaba receivers please?
peckle  14 points - 7/5/2014
 
This module works perfectly on my Futaba 9C radio. Just get the companion USB firmware update kit to update the channels to Spektrum channels and you are good to go. I used it to bind my 9C to the Blade 200 QX quad and it flew perfect. Just have to reverse all the channels. Great product!
Jeane  2 points - 6/10/2014
 
Does it fit airtronics m8/m11?
 Ivan 8 points
Nope. It works with Futaba and Hitec.
 Jeane 2 points
и* в* ч*ё*м* о*т*л*и*ч*и*я* о*т* www.link
 Jeane 2 points
and what is the difference between futaba/hitec and spectrum/sanwa?
 Ivan 8 points
The pinout is different - M8/M11 has 8 pins, this module has a 5-position connector.
 KillerJoe 62 points
so Ivan this will work with my Hitec aurora 9 mo probs'? all i want is a yes/no from someone who isnt a keyboard hero and knows from experience!
 Ivan 8 points
I don't have an Aurora, but from the pics of the module bay I've seen my answer is No. The reason is that the module has only 5-pin connector while the Aurora module bay connector has extra pins for fast digital connection between the transmitter and the Hitec 2.4GHz module. This module will work in the older MHz Hitec Optic 6, Eclipse 7 and Prism 7.
 KillerJoe 62 points
cool thanks heaps mate, i see there is a TX modal u need to wire into the controller itself and wonder if somehow i can supply the 5v & - and the ppm signal and have my hitec work on the dsmx protocol
 KillerJoe 62 points
i popped out my Hitec module today and what do i see? 5 pins sticking out of the radio! i do see that on the back of the Hitec TX module there are 10 sockets but only 5 are used with the Aurora 9 so this might just work after all!
 Jean-Philippe 3 points
So can anyone confirm if this works or not with an Aurora 9?
 Ivan 8 points
As is it will not work. The pins on the Aurora 9 are shifted to the side compared to the connector location on the module. As I already stated above, the module will work in the MHz module based Hitec radios which are the Prism 7, Eclipse 7 and Optic 6.
Customer Reviews
Overall Rating
__Ken
15 likes
Value
Quality
Like it?
I received my Futaba module this morning and I was very pleased that it came with a small set of user instructions. I plugged it into my Futaba F8UP [aka Field Force 8] and it fitted securely, more so than my FrSky module. I bound it to a Spektrum AR500 then a Spektrum AR6100 then an Orange 610 without a satellite and then finally an Orange 410. All these bound without a problem and all channels worked as expected, but of course not as labelled on the receivers due to the different channel sequence from the Futaba tx. When binding, the tx module somehow finds out if the receiver needs a DSMX or DSM2 signal, and if it should be 11ms or 22ms and then it starts up in that mode. When binding an led on the back of the tx module flashes a sequence to indicate what mode has been automatically selected. This was a bit confusing because when binding, each receiver caused a double flash of the light on the tx module, indicating DSMX at 22ms which I was initially pleased with as DSMX means true frequency hopping. However, when the tx was bound, my led was out, and the instructions say this indicates DSM2 22ms and not DSMX. There is a facilty to change the transmission mode, and suspecting that despite what the instructions say, the module might just be DSM2 only and the other modes might be just kidology, I did change to the other modes to see what would happen. None of the receivers woul


3 comments. Reply..

Overall Rating
__Ken
15 likes
Value
Quality
Like it?
This is the missimng last part of my first review!! There is a facility to change the transmission mode, and suspecting that despite what the instructions say, the module might just be DSM2 only and the other modes might be just kidology, I did change to the other modes to see what would happen. None of the receivers would work at all if I manually selected the wrong DSM mode and in the wrong mode the led on the tx module flashed a continuous 1, 2 or 3 flash sequence to indicate the selected mode. Once I manually set the module back to the correct DSM mode all returned to working correctly. Clearly the module will work in the 4 modes that it describes so it is not kidology after all.. I have not yet done any range checks but so far, it works. In addition, there is an "ID" button on the module. Remember the fiasco with some Futaba tx's being sent out with the same code? Well the HK site says that there are 4 billion unique ID codes assigned to Orange tx modules, and each module is individually assigned 5 of these codes. By pressing a recessed and therefore relatively inaccessible button on the module you can change in the ID code that your module is using, although why you would want/need to do that is a mystery. A range check will prove more about these modules but so far all seems to be well.


No comments. Reply..

Overall Rating
BIRGER
99 likes
Value
Quality
Like it?
Well, just tested the module using my adapter for Futaba square trainer port. It works fine with no problems (no regulator needed) and binds to both DSM2 and DSMX receivers using the instructions provided in the manual. However, as noted by several people in the discussion board, it does not provide the channel mapping that is provided by the Spektrum module for Futaba radios SPMMSFUT720. This means that if you want to fly the ultra micro bind-n-fly models with brick type receivers you need a transmitter that has channel reassignment capabilities.


2 comments. Reply..

Overall Rating
Fabien
13 likes
Value
Quality
Like it?
Beware! This module does not have the same channel assignement as the Spektrum DM8 module This flaw makes it impossible for you to use an Eflite BNF model with a Futaba radio that does not provide channel reassignement. To make it clear: you won't be able to use an MCPX, nano CPX, 130X or any other Eflite BNF heli/plane with you Futaba FF9 or T10. Unless you can dial-insome weird mixes, or re-assign channels, this module can only be used with Spektrum/Orange full-size receivers, and in that case, you'd be better off with a Futaba receiver so you don't need a module in the first place... In fact this module is just useless in most use-cases I can think of... Other than this little problem, the quality is fine, the module fits right in the radio's slot, there's even a buzzer when you bind a model (better than the DM8 on this point) and you can change ID (something not found even on Spektrum TX) which is great... Not a bad product at all, but it just misses the point, such a waste of potential... Please HK, do make a new version of this product with channels assignement similar to the DM8...


2 comments. Reply..

Overall Rating
knight4105
41 likes
Value
Quality
Like it?
This is a good Module works with all Air DSM2 and DSMX recivers, The unit will flash 1,2or3 with what receiver is being used from DSM2 22ms through DSMX 11ms. Not a good idea for the micro BNF as the channels 1,2,3 have to be assigned in the radio,witch takes some time.


No comments. Reply..

.....click here to see all reviews
Aff. Link