USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
The Turnigy AE series are based on new powerful microprocessor. The new CPU means ultra fast sync timing, crisper throttle response, less battery load and reduced FET heat buildup. Also there is a separate voltage regulator IC for microprocessor providing good anti-jamming capability.
Specification: Output: Continuous 80A, burst 95A up to 10 seconds. Input Voltage: 2-6 cells lithium battery or 5-18 cells NIMH battery. BEC: Linear 4A @ 5V Control Signal Transmission: Optically coupled system. Max Speed: 2 Pole: 210,000rpm 6 Pole: 70,000rpm 12 Pole: 35,000rpm Size: 76mm (L) * 34mm (W) * 17mm (H). Weight: 78g.
Features: High performance microprocessor brings out the best compatibility with all kinds of motors and the highest driving efficiency. Wide-open heatsink design to get the best heat dissipation effect. Improved Normal, Soft, Very-Soft start modes, compatible with aircraft and helicopter. Smooth, linear, quick and precise throttle response. Multiple protection features: Low-voltage cut-off protection / Over-heat protection / Throttle signal loss protection Programable via transmitter and Turnigy BESC programming card
Programming features: Brake setting (we recommend using brake for only folding props applications) Battery type(Li-xx or Ni-xx) Low voltage cutoff setting Factory default setup restore Timing settings (to enhance ESC efficiency and smoothness) Soft acceleration start ups (for delicate gearbox applications) Low voltage cutoff type (power reduction orirnmediate shutdown) Governor mode Built-in BEC Output(5.25V or 6V) Factory default settings: Brake: off Battery type: Li-xx (Li-ion or Li-Po) Low voltage cutoff threshold: Soft cut-off (2.6V) Timing setup: Low Soft Acceleration Start Up: Normal Low voltage cutoff type: Medium
Impossible de programmer l'ESC avec "Turnigy BESC programming card". Ma carte fonctionne sur les Turnigy PLUSH, mais pas sur le AE-80A !
Avez vous une solution ?
Unable to program the ESC with "Turnigy BESC programming card". My card works on Turnigy PLUSH, but not on the AE-80A!
Do you have a solution?
Impossible de programmer l'ESC avec "Turnigy BESC programming card". Ma carte fonctionne sur les Turnigy PLUSH, mais pas sur le AE-80A !
Avez vous une solution ?
Unable to program the ESC with "Turnigy BESC programming card". My card works on Turnigy PLUSH, but not on the AE-80A!
Do you have a solution?
Hi
The specs say linear BEC but the picture shows the esc with "SBEC" printed on it, which usually means switching BEC.
Anyone know which is right?
Thanks
Mmm- I might be wrong (like always) but I thought SBEC- means Linear,and UBEC- means switching?I think the S should stand for switching and U would be Linear better yet they should use a L for linear anyone KNOW for SURE and let us know
Thanks
Tim, most (brushless) esc's. come as a default to automatically detect and count the number of lipo cells as a default. When u plug your battery into your esc listen to the first number of tones that the esc gives, if you plug in a 3 cell it should beep three times then give a tone letting you know that it is armed. this process is the same for 2 to 6s lipos, i dont think this esc is rated for more but in my own experience i have never had to manually change a brushless esc for the cell chemistry and cell count, but on most u manually can go in and program them for that specific setting but as stated before it should automatically do that for use unless u change it otherwise.
Hi all .. how do we connect this? It has 3 blue wires and the motor (PRODUCT ID: TY500H-1700) red blue black.. As you see I'm new into electric rc :) Are there anywhere electric plans for heli setups ?
typically on most brushless esc's and motors the center wire on both the motor and esc is the neultral wire just hook up both the middle wires on both your esc and motor and then it s just a matter of switching the other two wires around to suit your motorsrotational direction, if its not rotating the way you want it to then switch the two wires around or reverse it by using the programing function on your esc.
The on,y option I have is to use the Tx and listen to the music. I have the white Turnigy program card and a second card but neither can write back to the ESC. Was in contact with HK and they also didn't know. These cards can easily program the Plush esc's but not this one. It also has more trimming setups than other ESC's
I'm pretty sure you can use this program box with this ESC. Another website sells the same ESC under a different brand name and they have a program box that works with their ESC that appears to be identical to this one.
PRODUCT ID: T-PRO-BOX
The build quality is great and the plastic housing is a step above all the smaller/cheaper escs. As far as performance works a treat, drawing an average 45amps for 15min and its cold to touch
Extrem guter und Zuverlässiger Regler zum kleinen Preis. Lieferung war auch schnell Kann ich nur weiter empfehlen
No comments. Reply..
Overall Rating
4/23/2013 ralf.mechler@uk
71 likes
Value
Quality
Like it?
Ich setze diesen Regler auf meinem Motor-Prüfstand ein.
Dort wird er mit den unterschiedlichsten Anforderungen gequält - funktioniert bisher tadellos!
Das beste: er kann mit der Turnigy 2 in 1 professionel Program Box in sekundenschnelle auf einfachste Weise umprogrammiert werden.
Bestens.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
