The much-anticipated and exclusive Turnigy GTX3 AFHDS 2.4ghz 3 Channel radio system is here! This great looking Transmitter uses proven channel hopping technology to provide a solid, reliable link for RC Cars & Boats.
The Turnigy GTX3 features a large Back-lit LCD, A quick access jog wheel for function selection and programming, 10 Model memory, Steering wheel extension as standard, a host of programming features and compatibility with the already proven HK-GT2R 3 Channel receiver. The GTX3 can also connect with the free to download VRC Race Simulator when used with the optional USB cable (not included, see related items below). The combination of great features and solid reliability means the Turnigy GTX3 could very well be the last radio you will ever need!
Specs: Channels: 3 RF Type: 2.4Ghz AFHDS Bandwidth: 500Hz RF power: less than 20DB Sensitivity: 1024 Low Voltage Warning: Yes (less than 9V) Fail Safe: Yes DSC Port: Yes (3.5mm PPM) Charging Port: Yes Power: 12V DC (1.5AA x 8) Weight: 395g CE & FCC certified 3.9" Blue Back-lit LCD
Programing Options: Model Memory (10 Models) Servos NOR/REV Steering Trim Throttle Trim Dual Rate End Point Adjustment ABS Settings EXP Settings
How can I remove the fail safe on this as it is not safe at all !
If by mistake you shut down your transmitter or you go out of range, the motor start a 100% forward during 30 seconds. It happened to me with a boat today.....
Ok, I find out the explanation in the manual.
Programming of the integrated FailSafe unit.
1. Function Description
The built-in FailSafe unit is mainly for the use on boats and cars. It is used
to prevent loss of the model in case of signal loss and returns the servo to
the position which was set before.
a. Turn on the transmitter
b. Turn on the receiver. The signal LED will flash continuously and
indicates that the receiver is ready.
c. Move the throttle lever on the transmitter in the braking or outlet
position. Hold the throttle lever in this position.
d. Press the Setup button on the receiver. The signal LED flashes for 3
seconds (see left).
e. The setting is saved and you can bring back the throttle into neutral
3. Testing the settings
a. Turn on the transmitter.
b. Turn on the receiver.
c. Turn off the transmitter.
d. The receiver will now lose the signal and drives the servo or the
speed control on the gas channel to the previously programmed
e. If these steps work, you have set the FailSafe.
Yes the PRODUCT ID: T1450-TX-3 fit perfectly ! I already have 2 *)
The T1450TX-3 lipo pack is an excellent replacement in radio's which used 8 x AA cells in flat formation, such as many Futaba or Sanwa models.
i highly doubt it but this radio comes with a receiver so you could easily switch it out.
1 thumbs up!
I bought that Transmitter and it is pretty good! BUT! Where is the delay for Steering and missing parts from the the first Version GTX3 from Fly Sky??? That GTX3 - HERE - is the Version GTX3B. Also is a NEW Version on the market called GTX3C !!! But the problem is also that the DSC connector from that Turnigy version does not LONGER work. The old version GTX3 works from Fly Sky. I sell it in the hope to get a better one with new releases and more features. What I get is a half version of the GTX3 from Fly Sky which does not work with simulator now! So again Turnigy - what do you think how long you can do that with your customers! I am very depressed.
1 comment. Reply..
1 thumbs up!
Nice RX! There are so much buttons! That is why it's a little bit hard to understand how to use them. But it is so cheap and it works great! Also it is compatible with hobbyking (HK) and turnigy (X9) receivers. I give "A " for it!
4 comments. Reply..
The feel of the tx is quite nice, better then i expected. The selection wheel/button feels very cheap. (but it was $36.00 which is cheap) I binds fine with GT2 rx's. The screen looks really nice, backlight is bright, and it is very easy to read. This is my first programable tx, so I can not compare it.
2 things I was disappointed in is the limited 3 character model naming, and the fact that the "10 models" is nothing more then saved pre sets. If you are on model #3, it will still pair to any rx it has been bound with. So if you have a rescue boat, it can not use this tx along with whatever boat you just got stuck.
overall I am very satisfied with the tx.
5 comments. Reply..
Très bonne radio.toujours super fiable.portée a perte de vue. qualité prix toujours le top du top . merci hobby