USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
TrackStar 1/18th Scale 14T Brushless power System (4300kv)
TrackStar performance now in comes in easy to select Combo package!
Using a Fast Silicon Labs MCU and high quality On-Semiconductor MOSFETs the TrackStar 18A ESC sets a new standard in high quality yet affordable car ESCs. With Intelligent MCU logic the TrackStar series ESCs allow extremely precise start up control and positioning feed back from the motor. Combined with the quality 4 pole motor this translates in to very smooth start up and acceleration and torque.
The Turnigy TrackStar 18A ESC also boasts a host of programing options not usually found in an ESC of this size and can be programmed with ease via the Turnigy TrackStar programing card (sold separately)
ESC Specification: Cont. Current: 18A Burst Current: 25A Car Size: 1/18th Battery: 2-3 Cell Lipo / 4-9 Cell Ni-XX L-BEC: 5V / 1A Output Motor Type: Sensorless Brushless Size: 30 x 26.1 x 13.8mm Weight: 26g (Including wires) Motor Plugs: 3.5mm Bullet type Battery Plug: Required On/Off Switch: Yes Reverse: Yes
Motor Specifications: Turns: 14T KV value: 4300KV Poles: 4 Diameter: 21.5mm Motor length: 37mm Extend shaft diameter: 2mm Length of extend shaft: 11±0.5mm Weight: 60g No loading @ 7.2V: 1.8A Max current: 30A Resistance (Ω): 0.037Ω Battery range: 2~3s 7.4v~11.1v Operation Temperature: 80° Max Temperature 130° Suitable car scale: 1/18 Suitable ESC: 25A Thickness of lamination: 0.2X20mm
hai adalberto, did you use this combo for turnigy 1/16 4WD SCT? how about a motor mount, is it fit for turnigy 1/16 brushless 4WD SCT?. or anyone can help me because my motor was burnout? thanks all
Yes you can. The holes line up. You would not need a new motor mount. But the 1/16 cars have a bigger engine than this. A much longer motor can. This will be a little under powered for a 1/16.
I would not get this for a 1/10 crawler because this esc and motor combo isnt powerful enough to carry a 1/10 crawler through the rocks i would suggest the hobbyking xcar 17.5 turn system. Hope this helped!!!!
Hello
I just received this combo and putted it in 1/18 turnigy f1 kart and saw weird thing. even without pinion gear when motor shaft is free it acts weird. when going from standing or low rpm to high rpm drastically sometimes it maintenance low rpm for second or two, and after that lag it goes to high rpm if I'm still holding the trigger. Is it normal? some kind of overload protection? or is my esc broken? tested on two different tx/rx and acted just the same. When hitting gas few times it goes normal 2-3 times and then another 1-2 times lags for 1-2 seconds... Halp?
Yes, a 3rd party heatsink will fit. However, the motor already has heatsink on it so the effect will not be as good as when you put a heatsink on a motor without the small fins.
Yes it will work without any issues. I wouldn't recommend the 10T as it is far too powerful and would make controlling your car quite difficult. I have the 14T in a mini-recon and it's already wild with a 2S lipo and crazy wild with 3S lipo! Enjoy.
Hello, I have a Himoto HI4185br - EXB-16 - 1:16 SCALE 4WD RTR ELECTRIC POWER OFF ROAD BUGGY W/2.4G REMOTE, this combo serves this model? Need to replace the battery? thank you
use it for this buggy . You don'have to change the battery but if you want performance , use lipo 2s or 3s . I'm using a nano-tech 1.3 , 2s in a 1/18 short course truck and it's crazy! the truck is an hsp caribe ....very powerfull...
The motor does not fit a duratrax vendetta buggy. The mounting holes are too narrow. Can someone point me to a 1/18 scale off road vehicule on which the motor will fit without modification please ?
I dont know any car in wich this Motor will fit without Mods. But in case of the MT18T ot the HPI MiniRecon (Both same Platform) you can easy drill tow holes cuas this motorplates have enought space
will this be a good replacement for the Brushless Inrunner 2040-4800kv motor and 25A Brushless 2~3S (with Reverse) esc found in the 1/16 Brushless 4WD Mini Rally - Extreme Edition
No, it wont make any differents. The motor you've got now is 4800KV, this motor is only 4300KV. So this motor would give a lower top speed. Remember to credit me, if it was helpful. If you've got any further questions feel free to ask :)
Perfect ESC! Fits like a Charm in the HPI Mini Recon. With 3S the Mini Recon is a Rocket. Like the way to Program the ESC with the Programming Card, let me choose the right Settings (Timing and Punch Cunchcontrol) to not melt down the Diffs of the Mini Recon.
Ordered one of these and it won't fit in my Tamiya TamTech GB-01 Hornet. The widest screw holes are too narrow for the Tamtech mounting plate, and there isn't really a way to drill different holes. Are there any sort of motor mounting adapters or something that I could use with this?
The Shaft of this Brushless inrunner is very long, so you can simply use 1 to 2 mm metal plate or alloy plate and Drill the holes for the Tamtechplate and the Trackstar Brushless motor in 1/4 different angles. so you have enough shapft lenght to mount the pinion.
lol! my motor shaft is completely round, so how should i screw the pinion on it? ^^
are your shafts also round? if yes, how do you get your pinions in place?
on the pictures up there it looks like ordinary shafts with one side flat...
i think it fits but its is underpowered, i have mine in a HPI Mini Recon and it Works perfect. But the 1/16revo (sold mine) is a bit too big for this i think.
hpi recon might be too heavy. i just tried the esc in the losi mini 8, no timing no punch and it gets warm. the recon i imagine to be heavier, the motor is 20mm in diameter with the finning.
i have this system in my Mini Recon! The Power is a lot! better than the RTR Brushed motor also on my NIMH 7.2 volts. You can set the Timing higher (i use 5) and get more Power. But for me NIMH are quiet good. With the 3S on it, i can only run on large places, its took fast
I have just popped this little monster in my M-R last night. I had to drill 2 new holes in the mount. You will also need 2 new M2.5x6mm screws. Using a nimh battery provided enough power compared to the stock motor but I have chosen to use the nano-tech 2s and 3s 1800Mah Airsoft batteries - wow!
i ran this in my losi mini late. all you need to do is on the losi's motor mount, the bottom screw mount for the motor needs to be drilled closer to the opening for the shaft and the hole spacings is alittle too wide for the motor to mount. works great. it wont wheelie on a 2s on the road though, but its a long car, and fairly heavy. it spins the wheels like crazy though.used this motor in the losi mlm on a dirt oval
Customer Reviews
Overall Rating
vzoli
9 likes
Value
Quality
Like it?
With a little modification its fit in a Maverick Atom 1/18 buggy.
Nice and reliable product.
The program card is recommended but with the default setting you can also use.
3 comments. Reply..
Overall Rating
@rtie
2 likes
Value
Quality
Like it?
On team associated 18r
Pinion 14t, 3s 1000mh battery
It is the best upgrade I've ever done
Motor runs cool but the esc gets hot easy fix with a fan
Run time, power, speed is awesome
I'm using it for drifting mostly and bit of street race
Love it!!
No comments. Reply..
Overall Rating
Geoffrey
7 likes
Value
Quality
Like it?
The motor does not fit into a 1/18 Losi mini sprint. The bolt pattern does not line up. I am going to try to make a custom motor plate myself because the original one does not work with this motor.
No comments. Reply..
Overall Rating
Grezoo
3 likes
Value
Quality
Like it?
Use my 1:14 truggy, ordered without programcard.. but good working.. Perfect forward, and slowly backward function.
The motor is high power in truggy... :-)
Im upgrade to "game" rc controlled truggy.. dc motor, and PCB out.. and ESC Brushless in to my car.. :-) Nicely and Perfect work.
This ESC working on 12V!!!! :-)))) (gamecar in 12V NiMH cell...)
up to 30 min game time!!!! ( 4 high lighting smd LED)
smart Amper Eating the set.. !!!! :-))))
No comments. Reply..
Overall Rating
Dennis
3 likes
Value
Quality
Like it?
Excellent little combo. I'm using this in a losi Mini T. It takes just a little modification of the stock motor mount to get your screw holes to line up but other than that installation was very easy. This system makes the Minit T a real blast! Programmed with the least amount of punch off the line (get the programming card as well!!!!) and it still wants to pull the front off the ground! Great little system and can not be beat for the price. Some of the best money I have spent in R/C.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
no, mine is completely round. is it a good idea to file it flat on one side manually? or may this result in an out of centre running behaviour? 
