USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
Compatibility: FASST 2.4G: Air Systems (7CH Mode/Multi Mode) & Surface Systems (C1 Mode) (3PK 4PK/4PKS etc.) FrSky TF Modules: TF-8M, TF-14M Features: Compatible with FASST 2.4G: Air Systems (7CH Mode/Multi Mode) & Surface Systems (C1 Mode); CPPM and RSSI (PWM) output - If CH3 and CH4 are connected by a jumper, CH1 will output CPPM for CH1~CH8, and CH2 will output RSSI (PWM); Light weight and small size; Two selectable failsafe setting options.
Specifications: Number of Channels: 4 Operating Voltage Range: 3.5V~10V Operating Temperature Range: -10℃~80℃ Dimension: 34*19*8mm Weight: 6.2g
Question: Is this receiver is compatible with Futaba 4PL?
Answer: NO. It is not compatible with Futaba 4PL.
This receiver is compatible with 4PKS-R, 3PM-X,3GR-FS (using 2.4GHz FASST)
yes, it should. the two different versions of this radio come with FASST receivers, so this FrSky FASST-compatible system should be okay. Futaba 3PM comes with R603FS and Futaba 3PM-X comes with R603FF ** again, both are FASST receivers.
Personaly I decited to don't do it.
I have an 1:8 Scale Monster Truck, so I have the place for 2 antenna's, and I wouldn't walk the risk of ruin my receiver.
But if you have an 1:10 scale sedan or smaller, I can understand it is anoying.
But I wouldn't walk the risk, so i didn't do it.
The receiver's range works fine if you use 1 antenna normally and glue the second to the body. You don't have to have both antenna's up to achieve max range of the unit. It is not recommended to cut one of the antenna's.
I have recently purchased FRSKY TFR6 for my Futaba FASST MEGA TECH 3PM 2.4G –* T3PM transmitter (3 Channel pistol grip).I tried so many times to bind each other, but not succeeded as yet. the manual say set your transmitter to C1 mode. can any one guide me how can i set my transmitter into C1 mode.my email address is mashkoor*orient-power****
Turn on the transmitter, connect the battery to the receiver while pressing receiver’*s F/S button. After the RED LED is
off and GREEN LED is solid, the binding process is completed and the receiver is operating normally. I got mine bound but it took a few tries.. i did not use the instructions. just did it til it worked
Even though there are only 4 connectors, it receives 8 channels and it can be configured to send all 8 channels through one connector, with another connector being used for RSSI -the signal strength. This configuration is particularily useful when you use stabilization/multicopters.
Have a look at the manuals available under the Files tab. As there is just one connector, you have to have a board that will accept that. It is called CPPM or PPM SUM. Check this pdf: t413****/news/best-rx-for-quadcopters
Hi, I'm thinking of using this in a 2.4GHz to UHF relay.
Apparently, few of the UHF TX modules are sensitive to the PPM frame rate, and do not function properly when frame rate varies (e.g. due to stick movement in Futaba 8FG)
Does anyone know if the PPM out frame rate is fixed in this receiver?
Anyone know if this receiver will work with a 3pk that has 2.4g module installed? And are there any settings that have to be changed in the radio itself. Thanks.
I am running one of these Rx with a Futaba 4PKS. Ch 1,2 and 3 work fine, but I cannot get anything to operate on Ch 4? I have tested another of the same Rx with the same result, nothing. Swap out for Futaba Rx and works fine. Any suggestions?
I think it is possible.
The original receiver is recommended for A 4PK 4PKS etc, and those transmitters are in the Item discription, so I think it is possible!
Hoped to help you
Ruud
Hello,
Does this enyone now if this receiver will work with A Futaba 4PK?
And does anyone now if I can use this receiver with A Hitec 7950TH High torque receiver on 7,4V?
Thank you in advance,
Ruud
how do u bind this receiver im having trouble ,does it bind with 4pks ?
i do same proceduce as futaba receiver .
Tx turned off ,
hold FS button 5 seconds turn radio on ,but dosent bind ,any suggestions or procedure ..
I just got my 3 TFR4 and they work awesome with my Futaba 3GR!!! Thanks for super fast delivery to sweden!!! Now I can play with all my cars in 2,4Ghz!!!
ciao!ho capito come funziona:turn on the trasmitter,put on the receiver's F/S button connecting the battery to the receiver.if the red led is off and the green led is solid the binding process is complete.very well than you HOBBYKING!
Hello,
works well as a receiver.
I can not run on my radio Futaba Trainer 10 Wireless Mode,
* Power LED does not light.
I put bridge channel 3 and 4.
What am I doing wrong.
Hola ,
funciona bien como receptor.
No consigo hacer funcionar en mi radio Futaba 10 en modo Wireless Trainer ,
no enciende led power.
Yo pongo puente canal 3 y 4.
Que estoy haciendo mal.
Not from frsky, they only make fasst compatible systems as well as other brand spread srectrum rx's and modules. I dont know of any other brands that will work with futaba's FHSS spectrum rx's.
i have tried this receiver with a futaba 3pmx. it works great, no problems and failsafe also works. working distance aprox. the same as the original receiver. i will buy more for my other models. hobbyking thank you for this product
No comments. Reply..
Overall Rating
rezuan
5 likes
Value
Quality
Like it?
how good this rec for futaba 3vcs,4pk,3pk,as i wana get 1 for spare,i just need really hornest and good advice before i buy thanks
Great product this one, im using it with a Futaba 3PM-X easy to bind and works treat, Cant go wrong for the price compared to a Futaba one....
No comments. Reply..
Overall Rating
joão Almeida
1 likes
Value
Quality
Like it?
O receptor é muito pequeno e leve pelo que é facil de arrumar no modelo, funciona na perfeição com o radio 4PK modo c1 sevo digital rapido,MULTIPLEX digi speed,BSC WOBBYWING, ando na pista muito tecnica em carpet TT indoor com 2WD e a resposta é muito directa e rapida!! Por 1/4 do preço, melhor que o F....A (mais pequeno e leve) é impossivel pedir mais! Parabens WK
No comments. Reply..
Overall Rating
nxm310
5 likes
Value
Quality
Like it?
Testé sur hexacopter multiwii cruius se. Je me sert du signal cppm sur canal1. tout marche bien et on peux programmer 3 voies auxiliaires suplementaires. Donc on ce retrouve avec un recepteur 7 voies.
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg){kind=small}
