Please confirm your location:


USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Batteries & Accessories > Li-Poly (All brands)
> Batteries & Accessories > 15C Discharge
> Batteries & Accessories > Airsoft
> Airsoft & Accessories > Batteries & BB Ammo & Miscellaneous > Lipoly Batteries

  RATED:

Turnigy nano-tech 2000mah 3S 15~25C Lipo AIRSOFT Pack

Turnigy nano-tech 2000mah 3S 15~25C Lipo AIRSOFT Pack

When it comes to putting rounds down range, no one wants to compromise on fire power! thats why the legendary Turnigy nano-tech batteries are now available for Airsoft combat. Higher motor RPM, less voltage sag and extended operating times equal better performance from your weapon of choice.

The nano-tech Airsoft series also feature 5C charge ratings putting you back on the front line faster!

Get an unfair advantage and make sure your opponents know that they have been taken out by nano-tech!

Spec.
Capacity: 2000mAh
Voltage: 3S1P / 3S Cell / 11.1V
Discharge: 15C Constant / 25C Burst
Weight: 162g (including wire, plug & case)
Dimensions: 125x10x20mm (Each)
Balance Plug: JST-XH
Discharge Plug: Mini-Tamiya (Mini Molex)
 
The nano-core technology in lithium ion batteries is the application of nanometer conductive additives.
 
1) The nanometer conductive additives form ultrastrong electron-conducting networks in the electrodes which can increase electronic conductivity.
2) These additives create a superstrong ability for imbibition in the carrier liquid to supply more ion channels. This improves the ability of ion transmission and ion diffusion.
Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.
 
Advantages over traditional Lipo batteries:
-Power density reaches 7.5 kw/kg.
-Less Voltage sag during high rate discharge, giving more power under load.
-Internal impedance can reach as low as 1.2mΩ compared to that of 3mΩ of a standard Lipoly.
-Greater thermal control, pack usually doesnt exceed 60degC
-Thickness swelling during heavy load doesnt exceed 5%, compared to 15% of a normal Lipoly   during heavy load.
-Higher capacity during heavy discharge. More than 90% at 100% C rate.
-Fast charge capable, up to 15C on some batteries.
-Longer Cycle Life, almost double that of standard lipoly technology

*The length of balance charging wire may vary


PRODUCT ID: NG2000B.3S.15

This product available from a warehouse near you!

Capacity(mAh) 2000
Config (s) 3
Discharge (c) 15
Weight (g) 162
Max Charge Rate (C) 5
Length-A(mm) 125
Height-B(mm) 20
Width-C(mm) 10
Update/Add my own data
Customer Data

Weight: 235g Quantity: 
United States Warehouse In Stock View Item
stock
10+
Price$15.30


acc.
  • Male Mini Tamiya/AR Drone/Airsoft to Female XT60 (3pcs/bag)

    Combo Price: $1.57   IN STOCK



Further discounts available for registered & logged-in customers.
 Customer rated
510
crowns
  
 
Total of 6 discussions.
Mark  1 points - 6/25/2014
 
This battery fit perfect in my Classic Army 2014 Spartan Version M4 with a Crane Stock. One stick in each side of the stock and one in the buffer tube. The stock can be fully collapsed with this battery installed.
jon-karl  1 points - 4/23/2014
 
any idea if this will fit into a kea g36c hand guard with a lipo alarm also inside?
Brian  2 points - 10/30/2013
 
For those of you wondering. This battery will fit in a SUB-C crane stock (Not your standard 9.6v 1600mah stocks. Sub-C is wider). I put two in one tube and one in the other. Classic Army usually has these stocks, and I think the Echo 1 OCW might have a sub-c as well. For those of you who have a G&G, KWA, G&P, etc. You can fit one in each side and one in the buffer tube. However, you will not be able to collapse the stock all the way (on my stock G&G I got one click away with VERY cramped wires). If you want to have collapsed Oper8r stock, you can do this buy buying a lipo buffer tube and doing the aforementioned configuration. If you have a buffer tube mosfet and a non-sub-c crane, you are screwed. Hope this helps.
Joe  1 points - 8/6/2013
 
This does not fit into the two crane stocks that I have access to. Both crane stocks have a solid buffer tube, so this should work if you can get your battery into your buffer tube. However, I cannot.
 Xtreme 1 points
Chief, this battery could fit, the middle cell goes to the buffer tube and the two remaining cell will to the left and right battery compartment.
Denis  1 points - 1/6/2013
 
For your question to if it's fits to MOE handguard...it is! And very well i would say, it fits allmost every M4 hanguard (the standart length). At first stage I had some problem with the wiring but then I learned to place it correctly thats all.
Customer Reviews
Overall Rating
nate
4 likes
Value
Quality
Like it?
great airsoft battery can fit most hand guards, didn't fit moe grip but the 1200mah version did also fit crane stock , and last more than 400rds just have to be careful with wire like any battery, cant beat the price,


1 comment. Reply..

Create an account
Overall Rating
jozef
221 likes
Value
Quality
Like it?
Vhodné aj na modelárske učely. Ak človek potrebuje články jednotlivo.


2 comments. Reply..

Overall Rating
rotarygod
5 likes
Value
Quality
Like it?
Battery works great! Excellent bang for the buck. Gun: CA M15a4 Guarder M120 Standard gears Systema Magnum motor Pulls hard and fast. 27 RPS measured on audacity, Same as my 9.6 4200 large type pack and this fits into a crane stock with room to spare.


No comments. Reply..

Overall Rating
Wiley
2 likes
Value
Quality
Like it?
Fits my G&P M4 crane stock easily, but the main power wires have to be extended to make the crane stock work all the way. Very good value!


No comments. Reply..

Overall Rating
2old2moto
2 likes
Value
Quality
Like it?
have 2 of these working great so far ,,, they fit in hand guard but they are really tight in a crane stock


No comments. Reply..

.....click here to see all reviews
Aff. Link