USA warehouse now open. Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
NTM Prop Drive motors are rock-solid performance outrunners with tight windings, quality bearings, correctly rated magnets, balanced stator and flux rings plus they are QC checked at 14 points, from material processing all the way through to final dyno test.
Because we design and build these motors completely in-house (from 3D/2D drawing to materials sourcing, machining, balancing, final assembly and dyno) we can completely control production and ensure product consistency from design right through to shipping the product to you. The removal of middle-men has meant we can drive better value to the market and retail these motors at factory(our) prices! All performance figures are real and tested on our own motor dynos. Our QC engineer checks and balances each motor before shipping to the HobbyKing.com warehouse.
Hello, I'm new in RC... I recently bought a 45A ESC, NTM 3530 1400kV and 9x4.5 three blade for my fpv raptor but i dont know how to measure Amp draw on ESC and motor :/ Do you guys think it will work fine ?
actually it was a 2 blade 9x4.7 sf prop. I ordered a 3 blade 9x6, but i lost my plane, the wind took it way into the forest.
I am pretty shure that it will work with a 3 blade prop, cause my esc neither my motor got warm at all (and it was a 30 amp ESC). I think i was using it around 50% of his power, so you will be safe.
And yes, it was a 1400kV motor.
this motor is overkill for corsair. try a smaller one (same, NTM series, 28 mm ones), and you need a better ESC (30A), and with more kv, probably smaller propeller.
When i plug in receiver,ESC, motor and battery to program ESC the motor plays 3 musical notes 10 times, pauses and then repeats. Do not know if this is an error message or what. Using a Hobby King 50A ESC and an Orange receiver.
Any suggestions
This means your ESC is in programming mode which means that your throttle is reversed and your ESC sees that when your batt is plugged in your throttle is wide open position.
Will this be ok with 8x4 prop for FPV Raptor. Having to replace burnt motor. Will I get similar flight time as the Raptor also had 1400 kn motor. Esc I already have is Red Brick 50a.
Jet72 " i would recommend the turnigy SK3 3536 1200kv with a 4s setup and a 10x6 prop!"
4s how many amps and what thrust with this configuration?
grateful
I'm using this motor ntm 35 1400kv 35-30 and a 8x4 prop on a tricopter and I'm a rookie at tricopter just built it and I'm only getting like 4 minutes on this battery it's a turnigy 2.65 3 cell 11.1v and the battery also says 20.30c discharge and I have hobbyking speed controller 18a /20 bed 2a
you can take a 7x4 prop and you will have 2 or 3 minutes more or use the 8x4 prop and take a 3s 5000ma 20c battery - with 8x4 you should have about 2.4kg thrust so carrying a 3s5000 20c (about 320g to 400g) should not be a problem!
Yes it can be if you can get the little cir-clip off one end with the right tools,but you don't need to as HK sell a prop adaptor that will fit the other end,just click on the blue box under the price tab,the one you might need is the top one which is this motors accessory pack and it will screw onto the other end of the motor so you wouldn't need to push the shaft through.
i am using 4 of this at my quadcopter, i am using 9x6 propeller with 4S 45C 4000mAh...max current at full throttle is 36A...my motors became very hot, is it normal? Thank you.
i would recommend a 9x4 prop, because with a 10x4 he max. power is over the limit!
with a 9x4 prop max. amps 31A and 1.6kg of thrust - mixed flight time is about 13mins!
i run this motor with a red brick 60amp esc and its amasing the prop i use is a 7by3 speed prop and a 4cell lipo and i manger to get my jet up to 100mph it was amazing
Yes, it is 10-pole... The NTM 3530-1400 is a bit unusual in being a 12-arm, 10-magnet motor
timing about 15 degrees as gary said is ok
if you need more -> Turnigy SK 3530-1400 is the more typical 14-pole motor.
Hi guys!
Can somebody help me with this: I purchased 4 of this motors to use in a quad copter. I also bought these propellers: http://www.hobbyking.com/hobbyking/store/uh_viewItem .asp?idProduct=11331
But the hole is to small to fit the driveshaft.
Anybody knows which propellers I should get?
Thank you!!
Ric
Bonjour, les deux graphiques montrent la courbe d'efficacité du moteur en Lipo 3S (3 Cells/11.1[v]) et respectivement 4S (4 Cells/14.8[v]) courbe en bleu clair, en fonction du couple[N*cm] .Le Pi (en mauve) est la puissance absorbée, le Po (en noir) la puissance récupérée ou utile, la kRPM (en bleu) est le nombre de tours du moteurs en milliers et I (en vert) est le courant absorbé par le moteur. Essentiellement, c’est la courbe rouge(Efficacité) qui est la plus significative pour les utilisa
Very nice motor. Weight is about 110g with the NTM 35 accessory pack mounted on the motor. I have measured the motor with my Eagle Tree datalogger v3. I uploaded the data to drivecalc.de You can use this software(english version available) to test the motor with different props and voltages. its name is: NTM Series 35-30A 1400kv - timing med (15) tested by me: Blue Angel
Works great in my Parkzone Trojan. However, make sure you realize this will not work with standard motor mount and the shaft is not reversible. I had to fashion my own mount out of aluminum.
Excellent motor! Teamed with a 3 cell Lipo, 50 A ESC and 10x6 folding prop, it pulls my 1.9 m wingspan, 1.2 kg heavy slope soarer from ground level to out of sight in only seconds, hardly getting warm. You can watch it on http://youtu.be/iEfw7Rz1OR0
Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved
.jpg)
