FrSKY ACCST technology is proven, approved by many model associations, tested and reviewed as the leading Chinese 2.4Ghz R/C Technology. If you think DSM2 or FASST is the best, think again!
New FrSKY ACCST (Advanced Continuous Channel Shifting Technology) gives you secure radio communicatios in 2.4Ghz band. ACCST 2.4GHz system shifts 80 channels around hundred times per second in the 2.4GHz band. This means that the system is completely resistant to interference in that band.
The Two-way Radio System developed by FrSky provides an additional return link that would be used for monitoring the Rx’s voltage, temperature, location, speed and so on.
Features: Advanced Continuous Channel Shifting Technology (ACCST is our advanced tecnology it shifts channel hundred times per second and there is no signal conflicts and interruptions) robust frequency agility. Easy to bind and very fast link-up. Excellent reboot time. True Diversity with two antennas. All channels can be programmed with Failsafe, quickly and easily. Quick and extremely stable in performance. Precise and smooth servo response. Extended range (1.5km-2.5km).
Receiver Specification: Operating voltage: 3.5 - 10.0V Power consumption: 100mA Resolution: 3072 Latency: 22ms Analog voltage: 0~3.3V Number of channels: 8 Range: 1.5km-2.5km Dimensions: 55 x 25 x 14 mm Weight: 12.4g Version: 2.0
You have to check if your transmitter is able to send in PPM mode then it will work.
PCM will NOT work
maybe you need a special cable or just replace the inside transmitter module
for shore mechanical it will not exact fit, use double sided tape or glue
Yes it does. I have one installed in a FS-TH9X (Same radio from FlySky instead of HK).
I believe the 9X (not the 9XR) has the raised plastic rectangle in the module pit just like the FS-TH9X.
you'll need to remove pins by removing the board from the inside and then cut away the plastic riser.
Thank you so much for the reply Pappy_Pete. I am looking at this and I think I'm paying a little more for telemetry. I am planning on only using this for park flying (not fpv)... will telemetry be of any use to me? I ask because I am comparing this to PRODUCT ID: JR-Combo . Thoughts please?
Interesting point..yes, the module is exactly the same only the receiver is different. Now it depends on why you are upgrading. Although I didn't flash my TX, I "use" the telemetry....the tx will start beeping if I get the plane far enough away that the rx signal coming back (the telemetry signal) is weak...I had a number of planes "shot down" by stray ghz signals where I fly when using the stock FlySky TX...I've had the new DJT module beep several times while flying letting me know I was getting near the range for the current stray signal noise level in the area (at least that's what I'm assuming is happening)...some days I can fly to out as far as I can still see the plane with no issues...other days it starts beeping much shorter...some days it even starts one way (either beeping short or not at all) and then later changes to the other, as if some data link suddenly came alive and is swamping my signal path or suddenly went quiet.
Hi everybody. I have this Pack but I would like to ask if i can use a TL-ANT2408CL TP-LINK 8dbi omni-directional antenna instead of the stock one. Would this antenna work. I already have this antenna and it fits in the antenna port of DJT Module. The Frequency range in the antenna specs says 2.4GHZ ~ 2.4835 GHZ. So what do you guys think, sure I can try it myself but till now the weather has been terrible, it is raining all the time.
Attention de marche pas pour Graupner MX 24 S. Le brochage du module DJT n'est pas prvu pour MS 24 S, diffrent des MX22. Photos d'un module Graupner et FrSky pour www.link va devoir fournir un marteau pour monter le module dans les MX24S 8-(
Be careful not work for Graupner MX 24 S. Watch the pictures.
3 comments. Reply..
2 thumbs up!
This is a standout system amongst the Chinese 2.4. More resilient link than DSM2 (Spektrum don't like to hear that) due to the hopping frequency. See http://rcmodelreviews.com/frskyreview.shtml for a review of the non-telemetry system. See www.link for discussion of the Telemetry. Frsky have made the protocol PUBLIC so anyone can design sensors (are you listening Hitec??)
The build quality of this is no where near that of JR, Spektrum or Futaba, but it is adequate. The PCB of the RX was not mounted flat so the servo pins did not fully line up with the hole in the case.
In terms of functions this is perfect, it gains a lock within 1 second, if you switch the tx off and then on, the bind comes back on instantly.
Setting the failsafe position is dead easy, just press the rx button for less than one second.
One thing to note, there is software available to upgrade this to v2, however, the supplied serial cable will only update the tx module. You need to build or buy another interface to upgrade the rx!! For v2 you need to upgrade the tx and rx! so that is a pain!
One other thing, the module can support telemetry and non-telemetry rx. However, to switch over, there is a tiny dip switch on the back of the module. It looks quite flimsy and I'm not sure how long it will last!
Overall, in terms of function this is definitely the 2.4 set to buy. If you consider what you are getting and the fact that it is probably as robust a 2.4 link as the Futaba, add the price of the kit and subsequent rx, you are looking at a major bargain (even with the average build quality).
Build quality not as good as Corona's. To fit module in my Turnigy 9x, needed to bend pins of TX - Corona had a perfect fit. Pins of the RX are not aligned with plastic cover. So much for disadvantages - that is why 1 star is missing. Positive aspects are: 1. Feedback when RSSI gets low, you hear beeping. 2. Range test mode (TX power reduced by 30x). 3. Start-up time below 1 second. 4. Fail-safe, which really works and is easily configured - just one touch of a RX button, or after firmware update, of a TX button! 5. Firmware update possibility - with RS232 (COM) interface. Whole update procedure is described in manuals, and can be easily performed. 6. Smooth response to slow sticks motion. Resolution seems to be really high, although I did not test some excellent servos. 7. Last but not least, telemetry. Out of the box low RSSI or low RX voltage is indicated by beeping, also possible to set alarms for low or high signal on two spare analog voltage ports (0-3.3V)
10 comments. Reply..
1 thumbs up!
Frsky telemetry 8ch distance on ground test, on futaba 9c The tx was cca 40m above rx points. At 5.37 km distance the bind was working 100pcnt www.link