Location: UNITED STATES
HobbyKing RC Model HomePage RC Radio Control Help and Support RC Hobby Forum Contact our RC Hobby Support Staff About HobbyKing
RC Model Planes RC Model Cars RC Model Helicopters RC MultiRotor and Quadcopters RC Boats RC Electronics
AIRPLANES AIRPLANE ACCESSORIES POWER SYSTEMS RADIO SYSTEMS
TELEMETRY & FPV
 
 
 
 
 
CARS CAR ACCESSORIES POWER SYSTEMS RADIOS
 
 
BOATS BOAT ACCESSORIES POWER SYSTEMS RADIOS
HELICOPTERS HELI ACCESSORIES POWER SYSTEMS RADIOS
 
 
 
MULTIROTORS ACCESSORIES POWER SYSTEMS RADIOS
ELECTRONICS ELEC. ACCESSORIES
EMAIL  PASS 
TOTAL $0.00 QTY 0
Planes & Parts
Helicopters & Parts
Multi-Rotors & Parts
Cars & Parts
Boats & Parts
Bikes & Parts
Scale R/C Tanks
FPV & Telemetry
Batteries & Accessories
Chargers & Accessories
Electric Motors
Speed Controllers
Robotics & DIY
Servos & Parts
Radios & Receivers
Gas/Glow Engines & parts
UBEC & Regulator
Power Systems
Hardware & accessories.
Tools
Clothing, Gift & Acc.
Sale/Liquidation

Language
Currency
USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Helicopters & Parts > Heli Blades > Main Blades > 600 - 699mm
> Helicopters & Parts > Heli Blades > Night Blades

  RATED:

680mm MS Composit 3D Night Main Blades

680mm MS Composit 3D Night Main Blades
680mm MS Composit 3D Night Main Blades


The night flight with RC helicopter models is unique experience both for the pilot and the spectator. The illuminated MS Composit night blades utilize the same high performance carbon composite technology as other main rotor blades. Fully integrated light and power sources do not influence the blade aerodynamics, and allow for extensive aerobatics. Each blade is illuminated by two bright LEDs, which create two concentric circles. The night blade design makes the blade visible even in eye-level and inverted flight modes. The blade power source is Li-xx cell. For cell re-charge we strongly recommend to use MS-00108 Charger.

You wont find a higher quality set of night-blades anywhere.

Spec;
Length: 680mm
Width: 60mm
Grip : 12mm
Hole: 4mm

*Charger sold separately.


PRODUCT ID: MS-76806Li

989g Back warehouse: 0 10+ $144.33
Email Buddy Issue Price War
Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated 5 crowns   
 
Total of 1 discussions.
allanchan  266 points - 11/6/2010
 
May I know if this is any good for T-Rex 600???
 Vladimir 20 points
Yes but blade on the tail rotor must be 107 or 105 mm and sometimes it may little contact but it is OK I fly with this blades on my HK600-GT Very cool
Customer Reviews
Overall Rating
PLATINUM MEMBER
17 likes
ValueUNRATED
QualityUNRATED
Like it?
These blades simply super I have bought one though for me it very expensively. But it is that costed. With them each flight this show. Passers-by and gapers will run together to look at this miracle. Not ???????? a beautiful show. Capacities of the accumulator suffice on 10 flights for 14 minutes!!! Charger MS-00108Li too weak for such blades. I have put on gymnastics 3 hour then have checked up pressure and have seen each blade was charged on 0,09 volt! (3,80 volts 3 hour MS-00108Li = 3,89 volts) very long to wait! Optimum to charge them in parallel a current 200maH and pressure no more than 4,2 volts. In these blades there are accumulators in capacity approximately 100maH and at a luminescence to burst consumes a current approximately 50maH


No comments. Reply..

Overall Rating
PLATINUM MEMBER
17 likes
ValueUNRATED
QualityUNRATED
Like it?
These blades simply super I have bought one though for me it very expensively. But it is that costed. With them each flight this show. Passers-by and gapers will run together to look at this miracle. Very beautiful show. Capacities of the accumulator suffice on 10 flights for 14 minutes!!! Charger MS-00108Li too weak for such blades. I have put on gymnastics 3 hour then have checked up pressure and have seen each blade was charged on 0,09 volt! (3,80 volts 3 hour = 3,89 volts) very long to wait! Optimum to charge them in parallel a current 200maH and pressure no more than 4,2 volts. In these blades there are accumulators in capacity approximately 100maH and at a luminescence to burst consumes a current approximately 50maH


No comments. Reply..

.....click here to see all reviews
 
Aff. Link

Copyright 2012 Hextronik Limited.
The HobbyKing.com®, OrangeRx, Turnigy, Durafly, nano-tech and other brand logos and names are trademarks of hexTronik Limited.
All rights reserved