Got this motor in the 3d Hawk80 kit from HK. Mounted with a Turnigy 20A ESC and 2S lipo 1.200mA. During testing without propeller works ok, but once I mount servo saver and the 8x5 propeller, you activate the throttle and you listen tic,tic,tic,tic, and nothing else..... Not even start speening!!!!
What am I doing whrong?
Tryed reprogram ESC, testes with 3S Lipo..... Nothing... Can some help me???
Please rephrase your question to be more specific. It's the same as the usual aluminum X-mount as provided with the larger outrunner motors except wood. Probably has good 'break-away' qualities to help save the motor in case of a crash.
Prop savers are good for just that: saving props, not motors. Clearly it's almost impossible to design the perfect 'motor saver' mount (most motors cost more than props, correct?) but I'd say using thin ply should give up before metal. I'll not be using this mount with my ADH300L due to the location in the model.
Delst well it is like this it will not be ever as good as it was but it can be rewound. You can down load the wire pattern from the internet. Give it a go this is a good little motor. I hope this helps.
Delst yes I do know what you mean. It is not worth spending more money, than a motor costs. I use the wire in old CRT monitors. All monitors have a wind of wire wrapped in tape around the outer edge. It does work. I hope this helps
Ooooh Please! Buy some decent quality wire of the Correct/appropriate gauge (local Electronics Supply House) and rewind it carefully... lots of info on how IF you look.
I do this on Most All of my Hobby King motors without ever running vthem beforehand. (they need it *-) Major improvements in running performances result Even IF you don't rewind for a different KV.
__bare I find it hard to wind as many time as the factory?? They pack it in. For light motor CRT wire works well. Yes there is a drop in performance. But it is a cheap quick fix. Still am not able to wind as tight. I even bought wire and still was no easier. BUT thanks!!
Odd that Even poor abused recycled wire
(Why?? As good quality wire is V cheap to buy New) should give far better than the horrible quality 'factory' wind efforts. Recycled wire is risky as it can /does have unseen damage.
IF you cannot get the wire on neatly and accurately?
Then perhaps you really should not be doing rewinding :-)
Maybe the good wire is expensive in India Bare. Ignore the fact Kellyann says she's from Australia He's actually from India and no that wasn't a typo she's a he from West Bengal. He has a bunch of at least 6 bogus accounts which he uses to ask dumb questions and then switches accounts to give an equally dumb answer and gets 20 cents a time. Sally, DelSt, Allison, Chris, Sharron and Bacter. All scamming accounts. watch out for his lies he will come on as a poor battered and abused little girl. He couldn't lie straight in bed. He even posted as a female he wished he had a wife, big mnistake and even tried to pass himself off as an HK employee. Be careful and let your mates know.
BURNT OUT MY MOTOR!! It worked fine on 9x4.7sf prop 350 3s 15c and 620 3s 15c, but when I upgraded to a 850 3s 25c the motor BURNT OUT in less than 30 seconds. This motor will work great on 2s but not 3s with a 9x4.7sf.
I got this motor with the 3d hawk and have had many flights on 1050 30c 3s rhino packs and 9X5 gws props and still going strong. It is important to use flexible glue to brace the wires down at the motor mount and stator. Plane hovers at just over half throttle.
Actually, what you do is reverse the shaft so that it sticks out of the end with the mounting screw holes. You loosen the set screws, then push the shaft out (a drill press works well for this) the other end. Hope this www.link
Very good motor! Prop GWS 8x4 3s-610mAh, with flying time about 6 minute. The punch is higher when using 30C
No comments. Reply..
I bought 2, used one to replace a geared 5:1 brushed 280, the other to replace a geared 5:1 brushed 370. This motor is about half the weight of the motors ithey replaced. Used a 25 amp brushless esc (I already had them) This motor likes 3s with a 9.47sf prop the best about 7000rpm, 120 watts about 21 oz thrust. 3s 10.47sf prop about 5000 rpm, 155 watts, 20 oz thrust and gets a bit too hot (for me). Mine had the second e-ring grove so I could put the shaft out the other side. Support the hub near the shaft when pressing out the shaft or you will have to get 2 small v block and a dial indicator to straighten the bell.
1 comment. Reply..
I have put given motor ADH300L Brushless Outrunner 1100kv on Kinetic 600. The axis has been turned concerning regular position. It is necessary to pierce deepening in an axis under the screw a fixing rotor. Holes have approached ideally. Flies Kinetic with this motor very well, draft suffices for launch vertically upwards. The controler 18A is heated with the given motor, I have put turnigy 30А, it isn't heated Я www.link данный мотор ADH300L Brushless Outrunner 1100kv на Kinetic 600. Ось была www.link www.link www.link www.link www.link www.link www.link в оси под винт www.link ротор. Отвер