Solo Pro FP II Tail Set

 Daniele 44 points

Write the measure of the original and i can help U

 jorge 9 points

thickness 1mmX1mm length 127,5mm thankx

 Brheli 158 points

No, this is just for the solo pro SOAR IV , II, I sorry man, but you can find on the 3d micro heli parts

 Marcial1974 39 points

Hi guy, no this will not fit the Solo Pro 100 3D. This tail is so small and weak for a the 100 3D. You will need to buy the stock one for the Solo 100.

 MarceloMMY 93 points

Because HK sell a lot of this... Buy and wait to be dispach. Good flies.

 JuanLucas 60 points

Im in your situation, waiting and waiting...

 Brheli 158 points

Just buy and you will recive HK sells too much of these

 asanado 17 points

HobbyKing stock Solo Pro parts (a lot of them) once in a while - it can take some time until it is stocked again. If you are grounded, don't wait, just buy it from somewhere else...

 Tsport 3 points

With Blade MSR it works. The question is the MSR is the same like mCPX?

 Anton 24 points

Same motor as mCPX, all nine eagle models (260,270 and Bravo)

 Dude rc 366 points

To avoid mortar burn out you must cut of the throttle when crashing. That is the simplest way you can use and don't let it over heat.

 Elias 1 points

If you are like me and fly more in circles that goes right, wich will use the tail mortar more then if you fly in left circles. If you fly in left circles the motor will release throttle wich will result in less usement of the tail engine.

 iKot_UA 25 points

Dear, buddhi prasanna don't fly more then 2 batteries and you will have no any problem with tail motor! i use Solo Pro about 1,5 years without motor changes. Also i can recommend you make tail more longest than now (about 2 centimetres). Its will reduce workload for motor.

 Ismac-BR 2 points

Dear prasanna buddhi, do not force too much your nine, fly up to a maximum of two batteries in a row. To avoid burning your engine with spray drops and short, stick a small foam surrounding the tail motor and protecting the wires. (Ismael Serejo - Brazil)

 vidi27 29 points

I very enjoy my solo pro and when i need to replaced the tail/main motor it's look like i push the end of it,so with a great smile i order a few spare motors and other parts.

 asanado 17 points

You can put a fuse to cut power if current is too high - The maximum current needs to be measured first.

 The General - x5 140 points

Dude, put in a micro heat sink and your solid mate.

 anotherrick 1 points

they make a metal mounting bracket that works like a heat sink

 magnusEl 1215 points

Total length is 112mm, so it probably will not fit.

 Roy_T 134 points

This shaft is about 110mm x 1.5mm (square) and will not fit the Solo Pro 100 3G. The Solo Pro 100 3G tail shaft is 140mm x 2mm (square) and is mounted at 45 degree tilt.

 iKot_UA 25 points

no! motor in this shaft too small for Solo 100G. for this model need more powerful motor otherwise your helicopter will always spinning.

 vinicius 2 points

exelente peça de reposição

 asanado 17 points

It may fit, but the motor is weaker, so don't use it.

 RC Fun 371 points

It is possible to change just the motor but for $3.00 it is easier to change the whole tail

 e_lm_70 421 points

I did replace a broken tail motor, using a main motor for an old PicoZ helicopter. It does need 2mm shrink tube and a little work on soldering ... it is not complicated. If you find a good motor maybe is also a better option. Look on eBay for 6mm coreless motor. But as stated above is faster and cost very little to just order a new tail set and go with a plug and play solution

 Sergey 54 points

Much more profitable to buy a new pair of tails at once!
What does the mending broken, economically
not profitable!

 JOSÉ 2 points

it is easier to change the whole tail

 officialsavage 1 points

This would not be an easy task, and probably not worth while given that the whole tail assembly is less than $4.00. The wires run through the boom, however if your good with soldering you could do it.

 wztwade 1 points

I think it is much easier to just buy a new tail set for that much money. I tried to fix mine, it kind of got messy too.

 vinicius 2 points

exelente peça de reposição

 CityDog 8 points

I do not know but for $ 3.86 is worth a try

 Nader 23 points

Yes you can, but you definitely need a longer tail boom -since this motor has a little less thrust (ca.80pcnt of the stock mSR). Hope this helped. Bests, Nader.

 Haruncan 1 points

You may need it because of a bad crash. Keep one in your toolbox.

 daryoon 11 points

You can use the motor. But some on the forums say it's a little less powerful than the mSR's tail motor. The boom on the Solo Pro is square, not round like the mSR. So it will not be a direct fit. Sorry.

 jsiki 6 points

****

 Chris_PL 10 points

noooo. It is too short. I bought it and want use just an engine .

 Aleksey 2 points

I think no. Many solo pro pilots made this tail more lenght for more stability.

 daryoon 11 points

Blade MCP-X uses a round tail boom. The Solo Pro FP II Tail Set is square. So it will not fit. Diameter of the MCP-X tail boom is 2mm. You can find replacement CF tubes, solid or hollow. Some people use the TREX 250 tail boom support and mod it to fit the MCP-X. Usually extending the length a bit from stock for better performance.

 asanado 17 points

You can make it fit, but it will be too weak to hold the tail (Mcpx head spead is higher then the Solo Pro).

 MarceloMMY 93 points

Hi man, I´m take a look in some photos of trex100,( I have a nine eagle heli), and i think that this solo pro tail set, can be use in your trex100, in my point of view, there aren´t any problem, and besides, you will pay less than U$$ 4.00 . Try this , and have a good fly.

 Moraes 65 points

Its same motor, works fine.

 Bisht 10 points

It can be experiment, but save you hell lot of money, if its work on Trex100. and suer u can use its motor if it dont work in Trex100

 asanado 17 points

Yes, it will work.

 MarceloMMY 93 points

It´s just arrived in stock. Good luck.

 Chin Keat 82 points

it is now in stock. hobbyking is selling the carbon fiber which can be a replacement.

 Roy_T 134 points

1.8mm x 1.8mm square CF rod with round hollow.

 hernan_g 15 points

Now in stock.

 Rcforme 210 points

Send a mail to HobbyKing.

 Roy_T 134 points

Stock just arrived. Hurry and buy!

 cosin 84 points

my parts arrived to me about month ago

 andrewsquare 2 points

Hi, I still Waite my order 19th of February. What estimated time for arriving this item?

 cosin 84 points

i ordered solo spare parts incl. tail on 14 feb and all of these parts are on bk. I contacted HK support and got answer that they do not know when or if it will be available again.

 goldie23 17 points

hurry up HK get some more in!!!!!!!!

 shimon 1 points

it will be in stock in end may

 edu82 6 points

So... End of may... Where is HKing?

 peluso13 5 points

End may? today is 31... more in the end??

 Daniel 9 points

three months and a half waiting now, come on, restore the items on backorder please!

 iKot_UA 25 points

****

 shimon 1 points

it will be in stock in end may

 benji1174 2 points

It's in stock now!

 iKot_UA 25 points

****

 jojoles 290 points

yes it is. you have to buy separately tail blade, if you want. good luck

 ThomasLite 8 points

yes, the tail set is sold without the tail rotor on.

 Javier 10 points

Yes, if you need the blade you have to buy separately

 HappyHeli 10 points

Yes Tail set is without blades

 neosfahrer 31 points

Yes, without Blade..

 Joker 86 points

Without blades.

 OptiPlex 7 points

yes the tail set is only the boom, the fin and the motor, no rear blades

 Esther 17 points

Yes, I do not think carrying the rotor, but worth 70 cents here.

 peraldavid 6 points

no blade on the set

 PILOTERO 36 points

Yes! This comes w/o tail blades *)

 NickyV 18 points

correct - this is a full unit with all parts except tail prop

 RUBEN 10 points

Mine comes mounted and without blade

 Michael 4 points

yes, no fan blade

 ravdigo 203 points

Only tail set, blade you buy in another parts.

 buikpijn 6 points

Yes, this tail comes without a blade. The blade is sold separately.

 RUBEN 10 points

Im waiting since january

 ravdigo 203 points

Do the login, select the product that you want, and look the option (in the page) "Stock arrival altert" - put your email - and click. When it arrive hk will send you an email.
Product are in stock 15 days.

 iKot_UA 25 points

****

 cees dorst 8 points

I think the are now on stock

 iKot_UA 25 points

****

 Sheal 2 points

It is in stock now

 iKot_UA 25 points

****

 iKot_UA 25 points

****

 GerardvSt 10 points

Yes it will!

 noontang 10 points

These stuff out quickly on the solo pro, you will need to get a couple for spare

 TrustyRuss 299 points

I would also like to know :)

 tonybooger 193 points

I would also like to know!

 Arief 1 points

Well it actually fits but it kinda needed more length due to the lack of thrust