Please confirm your location:


USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!
  Item found in the following categories;
> Radios & Receivers > All Receivers
> Radios & Receivers > 2.4Ghz HobbyKing
> Cars & Parts > Car Radios > Receivers
> Radios & Receivers > Car Radio > Receivers

  RATED:

HobbyKing® ™ GT-2 2.4Ghz Receiver 3Ch

HobbyKing® ™ GT-2 2.4Ghz Receiver 3Ch

HobbyKing® ™ GT-2  2.4Ghz Receiver 3Ch
 
Specification:
Model: Car/Boat
Channels: 3ch
Frequency band: 2.4Ghz
Modulation: GFSK
Sensitivity: 1024
RF. receiver sensitivity: -100dbm
Fail Safe: Yes
Power: 4.5~6VDC
Weight: 5g
Antenna length: 26mm
Size: 37.6 x 22.3 x 13mm
 
CE & FCC certified

 


PRODUCT ID: HK-GT2_RX

This product available from a warehouse near you!


Weight: 19g Quantity: 
United States Warehouse In Stock View Item
stock
10+
Price$6.45


Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
 Customer rated
5403
crowns
  
 
Total of 543 discussions.
DAVID  5 points - 7/21/2014
 
****
 NewToHobbyKing 13937 points
David you have been stared out sorry!
nrobe189  15 points - 7/19/2014
 
will this bind with the turnigy 9x v2?
 NewToHobbyKing 13937 points
Nrobe189 yes it binds to the Turnigy9XV2 (The complete one with the module). If your Turnigy9XV2 came with a receiver then this little receiver will work with it. Also this receiver has a built in fail safe.
BEST ANSWER CREDIT AWARDED
 nrobe189 15 points
thanks! greatly appreciated!
Stephan  6 points - 7/19/2014
 
*Sergei. Thanks for your reply, however, it doesn't answer my questions. I have dug in now, and don't think that I will be able to get my project work with the GT2B receiver, so let me ask my final question first: is there a receiver compatible with the GT2B transmitter that carries the PPM signal? Let me elaborate what I did so far: What I need is the PPM signal, which is basically all servo pulses time-multiplexed on a single wire. Most receiver carry such a signal* google "hack RC receiver" if you are interested. I need this for interfacing with an arduino, where I do not have sufficient free pins. "Hacking" a receiver refers to soldering a wire to a pin in the circuitry of the receiver so to get access to this PPM signal. I have by now determined that the HK-GT2B receiver does NOT have the PPM output (the usual place for this is the signal pin of the battery port, but that port appears to be unconnected). After playing with an oscilloscope for a bit, I could not identify any place in the circuit that carries PPM. There is one chip that awfully looks like the usual shift register, but I think it's a GAL, and I don't know what happens inside it. It's not the usual CMOS shift register solution.
 NewToHobbyKing 13937 points
Stephan very cool. This PPM thing does confuse me but the Turnigy9XV2 and its receiver does state it is PPM (and not PCM). Could you have a look and see if that is what you need. Me I am still getting my head around S Bus!
Stephan  6 points - 7/18/2014
 
Hi Gurus, Does this receiver output the PPM signal? If not, has anyone hacked it to do so? If not, is there a receiver compatible with the HK-GT2B transmitter that outputs PPM? Thanks in advance. Stephan
 Sergei 77 points
This receiver will work just fne with your HK-GT2B without any hacks.
-Elop-  4 points - 7/16/2014
 
would it work with the HK6S ?
 NewToHobbyKing 13937 points
Elop no this receiver is compatible with Hobby King 2.4Ghz 6Ch Tx & Rx V2 (Mode 2) (SKU: HK-T6A-M2). The only spare for the HK6S is HobbyKing HK6DF 6 Channel 2.4ghz Channel Receiver (SKU: HK6DFRX). If you need to reduce the size try removing the case and heat shrink wrap it!
Customer Reviews
Review Blogs for this item
Bind the HK-GT2 3ch 2.4 GHz with the Turnigy 9X V
Fabiomel
Create an account
Overall Rating
Jeffwazz
39 likes
ValueUNRATED
QualityUNRATED
11 thumbs up!
Nice compact rx. Runs fine off a 4.8V ni-cd pack. Binds easily with the GT2 transmitter, although I did feel I needed an extra hand to press the bind button while powering on the tx. All is good and works great!
Will buy 2 more to kit out my entire "fleet".


5 comments. Reply..

Overall Rating
drrk24
653 likes
ValueUNRATED
QualityUNRATED
5 thumbs up!
Seems to be identical to other brands like FlySky, ...
I've tested it successfully w/ a GT-3 Tx, available elsewhere (equipped w/ the actual v3 tx-module).


10 comments. Reply..

Create an account
Overall Rating
Malfamartin
680 likes
ValueUNRATED
QualityUNRATED
2 thumbs up!
I have two of these little buggers already and have now ordered two more. The Rx is basically made for car/boats, but can under certain circumstances be used for small planes on a small field and no bystanders (only one antenna). The antenna is 26mm as stated in the RX specs. but the cord is totally 180mm, which makes it easy get the antenna position right. Right price too. Now we are waiting for HK GT-3!!!!


4 comments. Reply..

Overall Rating
foamieflyer
9 likes
Value
Quality
2 thumbs up!
I have found that the HK GT2 works well I compared it with a 3 channel eurgle receiver they both have about the same range or apox 290 metre I would not take it pass this as they both lost signal at 300 metres and i found the HK GT2 slightly better so at the price I think they are pretty good value for small park flyers.I paid about $8 for the Eurgle from R2 hobbys,will be getting more soon.


19 comments. Reply..

Create an account
Overall Rating
clod_buster04
157 likes
ValueUNRATED
QualityUNRATED
1 thumbs up!
excellent price and nice compact size, would like to see UH/HK to start carrying the 3 ch transmitter, a lot of us like being on the ground and not flying


No comments. Reply..

.....click here to see all reviews
Aff. Link