Please confirm your location:


Arkansas warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the Arkansas warehouse even better value!
  Item found in the following categories;
> Hardware & Accessories > Wires & Connectors > Battery/ESC/Motor Connectors
> Hardware & Accessories > Wires & Connectors > Battery/ESC/Motor Connectors > Bullet Connectors

  RATED:

3.5mm 3 wire Bullet-connector for motor (5pairs/bag)

3.5mm 3 wire Bullet-connector for motor (5pairs/bag)

3.5mm 3 wire Bullet-connector for motor (5pairs/bag)



PRODUCT ID: 9001-AB

Shipped from:
International Warehouse

Price

$5.10

Related Products
Customer Also Bought
Further discounts available for registered & logged-in customers.
STOCK ARRIVAL ALERT

Enter your email address to get an email the second new stock arrives.
Estimated factory delivery date;
 Customer rated
5152
crowns
  
 
Total of 48 discussions.
Johan  6 points - 11/28/2015
 
Is there possible to put for instance one female and two male in the same housing for protection against conecting the contector the wrong way?
 carmar 2 points
You can't fit three bullets in a 2-bullet case. Consider using EC3 plugs instead.
 Gloon 1 points
If you did this it should prevent fully connecting the plugs fully together reversed, however the metal would still touch inside and form an electrical connection when connected the other way. However these connectors are typically for connecting the motor to ESC where polarity does not matter, and typically you will be leaving it plugged in for the most part anyways.
Bruce  1 points - 6/7/2015
 
I assume I should slide the housing onto the wire(s) before soldering and then pull/push it through after soldering is complete? Won't I need a pin pusher to do this?
 skyfox60 1376 points
Hi Bruce, a small screwdriver will do the job. Works fine. Hope that helps for Your decision.
 flatspin 350 points
Bruce: With this connector you don't feed the housing onto the wire first. Solder the wire to the connector and the push the connector and wire into the wider end of the housing using a small jeweller's screwdriver until you feel it go click. Give it a tug to make sure it is locked in the housing. Job done!!! It works best if the soldered connector is still warm from being soldered.
jeffT  49 points - 4/29/2015
 
Hi, What's the max wire guage we can solder to these connectors? I'd like to use them with 12AWG, will it fit? Thanks a lot Jeff
 Aytac 48 points
Hey 12AWG will be the maximum size that would fit this, so yes its all good. Reward :)
BEST ANSWER CREDIT AWARDED
Noah  1 points - 3/15/2015
 
Hi, I was wondering how these would be attached to a wire? I got a few Turnigy plush 25 A bulletproof speed controllers. They didn't come with any connectors. Would this be compatible with that? Also would I need any special tool to crimp these?
 BangerUpBixler 271 points
Hi Noah, you will need to solder these plugs to the wires of your Plush speed controller. If you need help to solder, I can suggest do a search on youtube for 'solder bullet connector' and you'll find a lot of helpful videos. I don't think there is any plugs that you can crimp on to the speed controllers wires that will carry the amps effectively through the connection. Cheers Michael
Dmaan  134 points - 12/17/2014
 
Hi Hobbyking. Can these be packaged in say two pairs instead of 5? I use these a lot but many users really don't want 5 pairs to try the product. Your new yellow triangle product is packed in two pairs and it is a far inferior product than this.
Customer Reviews
Create an account
Overall Rating
Malfamartin
686 likes
ValueUNRATED
QualityUNRATED
11 thumbs up!
Finally! Makes the motor installation nice and neat. Easy to change direction of rotation.


No comments. Reply..

Create an account
Overall Rating
dinazor
99 likes
ValueUNRATED
QualityUNRATED
8 thumbs up!
Very good connector for ESC


No comments. Reply..

Create an account
Overall Rating

106 likes
ValueUNRATED
QualityUNRATED
5 thumbs up!
Good value, cheapest in the planet


No comments. Reply..

Create an account
Overall Rating
Lonziz
439 likes
ValueUNRATED
QualityUNRATED
5 thumbs up!
Been on backorder for a long time. Hope they will help tidy up my motor ESC wiring.


1 comment. Reply..

Create an account
Overall Rating

46 likes
ValueUNRATED
QualityUNRATED
5 thumbs up!
These connectors make life a lot easier by keeping the wires organized. They handle the current without fail, and don't lose their coating. Highly recommended


1 comment. Reply..

.....click here to see all reviews
Aff. Link