USA warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the US warehouse even better value!


Public Profile
tasosgreece
Customer Type: Platinum Member
Location: volos, GREECE
My movies
 
Recent product discussions
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
someone to fix this gimbal with nex 5 ???...
Turnigy Multistar 4822-690Kv 22Pole Multi-Rotor Outrunner
if you use 1447 propeller the esc worm but with 6Ampere 800gram why warm the esc????...
2-Axis Brushless Camera Gimbal Stabilization Control Board w/IMU
hello how i change device to xloader because says only simpleblg...need to change that or not???...
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
some one to make pid for this gimbal????for alex moss ...
2-Axis Brushless Camera Gimbal Stabilization Control Board w/IMU
i have any problem if i use it for 4008 motors and nex 5???...
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
someone to bought this gimbal???is better for 5N Storm Eye Brushless Gimbal Full Carbon Kit (Mini DS...
AeroStar AS-470HB High Torque Standard Servo 48.5g / 6.21kg / 0.12sec
where i find replasement gear...
Turnigy Multistar 4822-690Kv 22Pole Multi-Rotor Outrunner
http://www.youtube.com/watch?v=gRdGjGwABCI&feature=youtu.be here it is my hexa 14:30 min flight ...
Turnigy Multistar 30 Amp Multi-rotor Brushless ESC 2-4S (OPTO)
http://www.youtube.com/watch?v=gRdGjGwABCI&feature=youtu.be...
Turnigy Multistar 30 Amp Multi-rotor Brushless ESC 2-4S (OPTO)
how i calibrate that esc????i use naza v2...
Recent discussion reply
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
NO IT IS 14MM...
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
i change firmware to 161 you have the p-i-d and pwr??i dont fix it yet and i try all the time to fix...
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
your P-I-D???i hve the same setup but with 207 and dont finish it yet.....
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
to me the alex mos with martinez board dont work very good i put brugi 207 and work better but i hav...
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
what is your pid...i think you use alexmos but mine didnt work good with alexmos.. roll didnt work g...
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
i dont fiz this problem to my gimbal i dont know why but roll have some jello...
ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 And GF3 Sized)
i have the same my friend i change the 4 dampers with something so hard dampers and tommorow i test ...
2-Axis Brushless Camera Gimbal Stabilization Control Board w/IMU
THANKS i didnt know need usbasp for upload nulled firmware....you have any tutorial for wire connect...
2-Axis Brushless Camera Gimbal Stabilization Control Board w/IMU
THEN I DONT HAVE ANY PROBLEM WITH CONTROLLER IF I USE 3S????...
2-Axis Brushless Camera Gimbal Stabilization Control Board w/IMU
i bought this gimbal ACK Pro Mid-Sized Ball Bearing Brushless Gimbal With Turnigy 4008 Motors (NEX5 ...
Wiki-blog entries.

Share