Please confirm your location:


Arkansas warehouse now open.
Our USA warehouse is now open! Low cost shipping and an ever growing variety make ordering from the Arkansas warehouse even better value!


Public Profile
James
Customer Type: Platinum Member
Location: Sydney, AUSTRALIA
My movies
Recent product discussions
Turnigy HD 5208 Brushless Gimbal Motor (BLDC)
Hey, does anyone know where to get the multi-pole motor as mentioned on the featured video?...
Afro Slim 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware)
do these fit inside the Talon carbon fiber tubes/arms?...
1/3-inch Sony CCD Video Camera 700TV Lines F1.2 (PAL)
So what exactly is that wiring diagram for this device? im not sure if its safe to power it up.. man...
SkyZone 5.8Ghz 200mw FPV Wireless AV Tx & Rx Set
For the Transmitter, is it black(ground) on the far right? and for its power, bacl(ground) is on the...
SkyZone 5.8Ghz 200mw FPV Wireless AV Tx & Rx Set
can i power this thing with a 500mAh 20C 3S LiPo? will it be safe for the transmitter and camera to ...
SkyZone 5.8Ghz 200mw FPV Wireless AV Tx & Rx Set
when will this be in stock and when was the last time these were in stock?...
Turnigy Talon Tricopter (V1.0) Carbon Fiber Frame
This is in my wishlist but am still waiting to be restock so i can purchase my complete shopping lis...
SkyZone 5.8Ghz 200mw FPV Wireless AV Tx & Rx Set
Hello, im worried about the UBEC delivering too much current to my transmitter... how should i go ab...
NTM Prop Drive Series 28-30S 900kv / 270w (short shaft version)
My surclip is loose thus when i press on the bottom shaft, the motor shell pops out loose... is ther...
Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 1) (v2 Firmware)
Hi, ive got a problem with my transmitter... all my switches arent working... only Channel 1-4 are g...
Recent discussion reply
Multistar High Capacity 3S 5200mAh Multi-Rotor Lipo Pack
Parallel or Series? i think it will be ok in parallel but balancing might be an issue... needs to be...
Turnigy™ TGY-306G Ultra Fast/High Torque DS/MG Alloy Cased Servo 3kg / 0.06sec / 21g
try your local hardware shops, these screws may be common...
Turnigy™ TGY-306G Ultra Fast/High Torque DS/MG Alloy Cased Servo 3kg / 0.06sec / 21g
try this one http://www.hobbyking.com/hobbyking/store/__26370__Aluminum_One_way_Universal_Servo_Arm_...
Turnigy™ TGY-306G Ultra Fast/High Torque DS/MG Alloy Cased Servo 3kg / 0.06sec / 21g
Have you tried moulding your own arm? and customise it? seems like a good idea...
Afro ESC 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware)
It can deliver 20A continuous, maybe thats the Max current, i wouldnt push this over 20A as it might...
Turnigy Multistar 4225-390Kv 16Pole Multi-Rotor Outrunner
it says Max current 15Amps, so maybe anything over 20A ESC will be enough...
Afro ESC 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware)
try to test it individually, swap out the esc for a working motor, if the esc is still not working y...
OrangeRx Futaba FASST Compatible 8Ch 2.4Ghz Receiver
it will work with any futaba FAAST system i think...
Turnigy PRO Steady-Hand Gimbal 3 Axis KIT
The standard Turnigy HD 5208 Brushless Gimbal Motor (BLDC) will be fine to use, unless you use an ov...
Afro ESC 20Amp Multi-rotor Motor Speed Controller (SimonK Firmware)
it says those motors run at 20Amps max... maybe these are too small for your motors, most likely it ...
Wiki-blog entries.

Share